How to Make a Basic Cobra Paracord Bracelet

Native American Crafts
28 followers
6 Video Views·Aug 23, 2024
In this video, learn how to make a basic 4 strand bracelet with square knots, also known as the cobra pattern, using nylon parachute cord and plastic buckles.
Hi, this is Megan with Beadaholique.com and today I'm going to show you
how to make a basic two-color paracord bracelet with a plastic buckle.
And it's going to be just a very simple basic version. There's a lot of
different ways to do this. I'm just going to show you
the most basic simple one.
So a few things, you know, working on this. You'll need
a basic disposable lighter. Don't use a micro torch for this.
It'll burn right through and burn up your
nylon cord. You do want just your basic disposable cheap lighter.
You can also, it's really handy, you can use the side of the lighter where it's
smooth to smooth out your ends when you're
finishing off the bracelet, which will get the lighter kind of funky. So just
use the cheap little disposables. And then you'll need
your parachute cord or paracord. This is a two-color
project like this one. So I'm using two lengths,
one of each color. And then you're going to need these little plastic
buckles. And this is the 0.6 inch. So six-tenths of an inch is this size.
And this is the perfect size for doing
basically like the two strand cord with the two strands on the outside. So your
super basic one is going to fit perfectly
on the 0.6. You need something pretty strong
to cut through the paracord. I'm using flush cutters
because I found that my little scissors were a little wimpy.
If you have stronger, bigger scissors, it might work fine.
When you are cutting your paracord, you're going to want
to cut about a foot of paracord for each inch
of knotting that you want. And as far as how much knotting you'll want,
your clasp, this buckle, will add about two inches when it's closed
from here to here. And then you also, because it's thicker, you want to add
about an inch to your desired measurement from
what your wrist measurement is. So my wrist is about six inches.
I wanted my bracelet to be seven inches, which means I only want five
inches of knotting from clasp to clasp. Because then plus the two for the clasp
gives me seven inches, and it fits nice and snug.
I went ahead and cut six foot lengths of my paracord
just to give myself a little bit of extra working cord.
So one thing that you'll need to know how to do
is how to join two of the cords together.
First thing that you're going to do is take your buckle and separate it.
So these will go through the top edge of the male
half of your buckle. So take one of your
short cords, your center cords, and pull it a little longer.
And you're going to give yourself a little bit of a tail.
Bring it through the female end of the buckle.
Don't pull it all the way out. And tie a lark's head knot by just
pulling the ends through the loop. And just pull the other buckle
and the other string and everything all the way through.
And pull that tight to attach it.
You're going to take
your cords, and what we're going to do is we want to
attach this end of this cord to this tail on this one so that we have one
piece so that you get your two-color cord piece going up the middle.
Now there are a couple of different ways to attach
your cords to fuse them together. You can just trim both ends,
heat them with a lighter, and try to smoosh them together. I like to
kind of make a male and female fit together kind of a join.
So trim down this tail here. We want this join to be close to the
buckle. And it is going to take a little bit of
to do the join. And you do want the join to be high up enough inside the knotting
that it is encased in the knotting to make it strong. So
give yourself about an inch and a half or so,
inch and a quarter, and trim that down. So you're going to pull down
the outside of your cord and have the core threads
exposed. And cut off about three quarters of an inch.
And then you're going to pull your cord back up.
And now you want the end that's going in there to be
a clean end. And it helps if you have it already
fused a little to itself. So you just hold it in the flame.
And you'll see it get dark and shiny. You can see it melt. And when it starts to
melt, then you can kind of push it against the
side of the lighter. Be careful when you have it
melted because that will burn you if you touch it. It is very hot.
So make sure you let it cool off before you touch it. And
now you have this piece here and it's hard so it will be easier to
settle it in. So you can see that the top here is hollow because we cut out the
core threads. So you can take this piece
and kind of twist it and shove it into the top here.
And if these ends get frayed, that's fine because when you fuse it, it will just
give it more to fuse onto. Now you're going to take
that join. Be careful not to get stray cords in
front of the flame when you're doing this because they will
get melty and get ruined. So just turn the join
and fuse it together.
And don't melt it to the point that you're
going to melt right through it. Just get a good solid
fuse on it so that those are really solidly connected.
All right, so next you're going to decide the length this way. So as I
said, you want your bracelet to be an inch longer
than your wrist measurement and your clasp
adds two inches. So I'm just going to use this one as a
guide since I already did that one and I know
what fits me for my seven inch bracelet. I know I want
the middle from the end to the end from where the plastic stops to where this
plastic stops to be about five inches. Now
the basic knot in the super basic paracord bracelet
is a macrame square knot. It's also in paracord called a cobra
but it is the same thing as a macrame square knot. So I
have showed you how to do that in a video before. I'll go over it again here.
I'm going to take your cord. It's a little tricky to work with
six foot pieces but you get used to it. So you're going to take your left strand,
bring it over the center strands, your right strand,
bring it over the tail of the left strand,
and then bring it behind and up through the loop
and then pull both sides tight.
And then you're going to do the opposite. So you're going to take your left strand
and go under the center, take the right strand
under the left, and then bring it over and
through the loop.
Again it's going to be left over, right over, under, and through.
Left under,
right under, over, and through.
And I always like to think of it as just over, over,
under, through.
And then under, under, over, through. If you make sure that you
alternate them you will get a nice flat piece. If you don't alternate them
it will twist. So if you see it starting to twist
and you don't have the same color down the sides you're forgetting to
alternate. So again it's over, over, under,
through.
Under, under, over, through.
And you're just going to keep doing that until you get to the end here.
So when you get all the way down to your other
clasp you're done. You can see that it depends
a lot on how tight you do your knotting and everything.
You will have extra cord and you can do smaller
projects like key chains and stuff with your scraps but
as you work you'll get more of a feel for how long
you need to cut your cords for how many inches.
So as you can see I did six feet for five inches.
If I'd have done five feet for five inches I'd still have a couple of feet
left over. So it's kind of a guessing game because
a lot of it has to do with the tension. If you use
looser then you will use less cord. If you do your knotting tighter you will
use more cord. So pull your last knot really nice and
tight. Then you're going to cut off the extra
which is why you not want that knot tight. Leave yourself
just a little bit of cord. Maybe an eighth of an inch there
or just slightly longer.
Then
the way you finish this is the same way that you fuse it. You're going to melt it
and this is when you're going to use the side of the lighter. So
you're going to light the lighter
and you're going to hold it to the end of your cord and you're going to let it
melt until the whole extra tip, that whole eighth of an inch that you cut
looks like it's melty and then really quickly you're going to
squish it with the edge of the lighter.
You can see what this does it's going to expand
the end and it's going to fuse to the edges around here.
The idea being it's only secure if it doesn't pop back through that knot right
there. So by making it bigger and by fusing it
to the edges around here it's going to keep it
secure and keep it from popping through. And like I said you will get
goo on your lighter just wait till it's cooled off all the way and you can
scratch some of it off. But that's why you don't use grandpa's
zippo from world war ii. Okay so once more
hold it on there and let it get all melty
and then smooth it out. If you don't get it all nice and smooth
the first time you can reheat it and go back and smooth it out.
Just be careful if you've had the lighter lit for a little bit
then the part that you push to light it does get very hot.
You might need to let it cool off don't burn your thumb.
All right so once you have the ends all nice and sealed and it's not going
anywhere then that
is your finished bracelet. It's really simple and once you get it down
it is really quick too.
