Lecture 35 - Ground Penetrating Radar (GPR) and its Applications - Part 2

IIT Kanpur July 201
20 followers
Jun 6, 2024
[Music]
welcome back so yesterday uh we
discussed about the the working
principle of GPR and what is the
importance of GPR why we wanted to do
and what were the the outcomes okay and
uh uh this was the last slide where we
were discussing about the utility
mapping and as I told that uh uh since
uh the infrastructure development is uh
on very high scale in India this type of
mapping is getting more and more uh
common in most of the regions and
wherever so we are coming up with in
smart cities mainly so there we need uh
uh this type of surveys now this type of
surveys are required because and most of
the uh uh the occasions we don't have uh
the subsurface uh utility Maps available
with us and uh if we have to put for
example any flyover and then Piers have
to be uh or the columns have to be put
there so we may not we like we uh should
know that what is the what is the
utility under subsurface and that should
not be punched so so as I told that uh
the the import the beauty of having the
3D profiles um are that we can have
multiple uh slicing and at what depth uh
the uh the particular structure or the
utility lies that also we can know and
even we can know the depth at which it
goes plus the dimension of the uh the
particular utility or a
structure so
uh now further uh we'll just just try to
see that what uh we have uh gain in this
so we have for example this is the
another profile which shows the utility
at different depth uh based on the
hyperbolas and as I I was mentioning
that you can also try to understand that
what is the direction or the alignment
of the utility for example here if if
you take this uh uh hyperbola here this
one here and and we are having different
sizes okay
at uh different uh interval in in terms
of the uh the vertical section so you
can you can connect and then then even
manually you can do uh with your own uh
uh this thing but if not then even the
software can help you inp putting the
SEC but you need to identify the uh the
uh the features in this region okay like
uh what I have shown so this is one
advantage of 3D and also so the depth so
you can easily make out and say that
until this depth uh below this you don't
see the utility so utility is within
this Zone
actually in terms of the depth and all
that okay now uh little bit more about
that what uh uh parameters you can uh
select and uh depending on the terrain
in which you are uh uh doing the the
survey so uh and and uh what is the
desired depth
so depending on your target depth and
the area or the terrain in which you are
mapping or conducting the survey you can
use different modes okay so here for
example in this system and as I told
there is another system which is Sir
4000 uh we can have different uh uh
scanning modes actually so like data
search is there concrete scan structural
scan utility scan geology scan mostly uh
in this scans okay the utility scan
structure and concrete uh there are few
very uh like fixed parameters which had
been input by the by this within the
system but in this one this is what in
in 4,000 uh uh we can we we what we say
is the expert mode
okay so uh uh the data search and the
expert mode here are the same so expert
but in ter search you can you can modify
your uh uh requirements or the
parameters which as per your uh desire
and depending on the experience okay so
we'll briefly discuss that what are
those parameters uh while collecting so
if you see the screen this is what uh it
it will look like actually so this is
the first stage and then first of all we
need to be very careful about that what
is the vle we are getting here that is
also known as the U scope so it should
not shoot up on very uh outside the
range okay if such such shoot ups are
there then we should try to reduce the
gain or we can we can try to change uh
the parameters like uh uh what we are
having the the dialectric constant and
all that okay so in short this is what
this the system you will
see and mostly we'll try to collect the
uh the in continuous mode and uh so it
will
be
mode and then another one is that in the
metric system so in meters we will say
okay and and also so that is the
horizontal as well as the uh depth
section will be in in meters you can
also look at in the Nan seconds also
that also you you will be able to see
here so this is what we call the depth
scale if you want to see that this is
all in in this is in centimeter but
mostly we take in meter actually now the
first part which we have to be careful
is that what is the uh the the the
frequency range you are using here it is
400 and 400 or maybe you can use a 200
mahz antena and and then another system
what we are having is uh with the uh
350 mahz antena so this is one but but
usually uh another one here we can you
can put here is the 400 MHz also so 400
MHz as I told that this is been used for
the shallower that these are slightly
deeper and this is also again uh we can
go up to 6 M or so uh comfortably so we
have different parameters here like uh
so radar signal here so 400 then what is
this T rate more distance we will just
try to see that so other than that the
Enda transmission rate in kilohertz that
is your T rate transmission rate is
there and transmit uh High transmit
result results in fast collection of
data okay so if you if you do that then
you that system allows you to collect in
the faster mode okay and Sample here is
this one here okay so it it goes in in
in a in a uh like a uh range of like 250
then you are having a
uh uh then 256 1 15 12 124 so this is
this is each
uh scan curve is made up of numbers of
data points known as samples samples are
directly proportional to the smoothing
of curve and vertical resolution so this
will depend again that what uh type of
data in terms of the resolution you are
trying to collect okay so mostly we try
to collect in in this one if you want to
collect very um high resolution data
then you can increase this uh the sample
per scan but that will make your system
slow and you also need to move uh on on
the move the the GPR on the surface very
very slowly okay so this movement will
be restricted if you increase the uh the
number of scan okay per second then the
format is okay fine 8 Bits or 16 bits
mostly we take in 16 bits is it is
recommended and the range as I told that
either you put it in um the uh uh this
range mode that is time window and nanc
this again and the the you will take in
two-way travel time so the waves
propagating and received back okay now
that will also uh uh like higher the
range allows the deeper penetration so
if you increase the range you will be
able to uh penetrate deep but depending
on the terrain and material of that you
will have to judge based on the uh the
uh your uh wiggle or maybe the O scope
what your are getting depending on that
you can do that okay and the rate is uh
like what we uh we are talking about
rate is here so rate is number of scan
that will be recorded per second okay so
that also you can you can again set okay
the rate should be set high in case of
using the survey will so if you're using
the survey will then the rate has to be
higher otherwise there is another uh
method also what we do is the point
method okay so you like for example you
have kept the your syst system here at
in in and then you have moved here again
and then you have collected the data
that is your point mode collection but
mostly if you are connecting the survey
wheel then you are going to have like
you can keep the the rate a bit higher
and that will allow you to move faster
okay then we have the usually we give uh
this I low pass filters that allows the
frequency lower than the entered range
okay so they it will it will allow the
uh the frequency or the the uh frequency
lower than what we have entered so
mostly in 200 meh antena we take 550 and
uh 600 uh like that that is a high pass
allow then then high pass filter is it
allows the frequency higher than the
enter one okay so whatever you have
hired uh entered the frequency uh that
will be uh will be limiting that the
portion of uh the the data collected now
stacking is also important and that is
mainly used for uh the uh noise
reduction so high frequency noise
reduction technique smoothing high
frequency features
andate low frequency features so this is
this is what we do stacking mostly uh we
we put stacking which is around like uh
in 2D around 13 to 14 and if you taking
3D then we put nine okay so these are
the the uh the values which we have also
with the experience we have fixed up
that in this type of and particular
terrain what type of uh inputs we have
to put so then dialectric constant this
component reflects the velocity of the
radar wave moving through the material
and dialectric constant is inversely
proportional to the depth of penetration
okay so this is again uh an important
point along with the the
the frequency frequency of the equ now
to acquire the better results
pre-processing should be done by putting
respective equation parameters so these
are
the uh parameters which usually we use
and then and as I told in you can
collect the data in three 2D and 3D okay
so 2D if you if you have the like for
example the surface here then 2D you
will take in One Direction okay whereas
in 3D so this is this is 2D you you are
taking in 3D suppose this is the area
you are having then you you finalize
that okay this much grid I want to do
here then you measure the grid and then
you give uh XY and the starting point 0
0 and then keep collecting the data in
both the direction you can also go like
you can divide this every 50 cm or every
1 M you can collect the data and you can
go in zigzag way okay so you can collect
the data in this fashion okay and then
after finishing this you move in this
Direction so this will give you a pretty
good uh handle like uh to see the what
what is sub what is exactly there in the
subsurface so this is a uh instrument
with the 400 mahz antenna this is 400 MH
antenna we are
using and uh again as we we we talking
about this is the the survey wheel
actually okay so there's another one so
this is survey wheel and then data has
been collected over here this is uh the
model which we are having sir
3,000 so this is the part which we did
uh in one of the archaological site um
in uh uh near
barel now I'll I'll show couple of uh
results what we have obtained using the
uh the the GPR so initial aim using GPR
was map maing subsurface deformation
this is what we we were doing for the uh
for the part of uh like as a geological
mapping and then to locate the uh mostly
the uh the ancient structures here okay
so that what we did so for example uh
this is from uh uh
kach Kut
Gujarat so uh we found some uh AAL
feature along the cliff but we wanted to
do the surve here so this was been done
the the GPR was been moved on the
surface and we wanted to go deeper and
see that what exactly the deformation
has to tell us actually here okay so
this is the profile which we collected
and based on the discontinuous and
warped uh Reflections you can easily see
this that is warping here okay so this
based on this we Mark the fults and this
is is what are the arrows are showing
the the fa fault plane okay this is the
section 2D section we are looking at and
then uh we open up a trench here so this
black box uh broken line with the broken
line shows the trench area so we
escalated the trench and this is exactly
what we see here okay so you can match
easily so this is this one is over here
this fault and this fault which is
running here is exactly which you can
pick up along in the in the plane here
so you you we were able to match what we
see in the GPR similarly another
exercise we did in himalia um on on the
Left Bank of the Bas River and here also
what we did was that we uh we open up
the trench after doing the GPR part okay
so this is the trench section and the
GPR was been uh the data was collected
initially so this has eventually reduced
our uh time frame and also the cost of
excavation because we were very then we
knew that where exactly we want to dig
and the same case goes for the uh the
utility mapping or even for the for the
excavation which may be followed after
the GPS survey in archaeological s set
so this is exactly what we we saw this
is the plane here the fall plane is here
again the similar type of uh uh the
conditions we have applied here like we
we use the warping of the Geor radar
reflection as well as the sudden
discontinuation of the Geor radar
Reflections have been considered to
identify or infer the F fall plane and
this this again the dotted line what we
see is the trans section and exactly it
matches with what we saw in the GPR and
this is this this place is again in in
this same area not exactly the same but
uh quite little bit far maybe 2 3
kilometers away from the first site
which I was showing now here uh the
issue came was we wanted to uh do the
geological um like uh investigations
here by digging trenches and all that
then uh and according to us this is the
the theault should might probably passes
through this area here where the arrows
have been marked and uh when we were
discussing with uh the local villagers
they told that there is an uh pipeline
water pipe line which probably was been
put way back uh in this region okay so
that should not be disturbed otherwise
the uh the many uh villages will uh face
water problem okay so we said we have
the instrument which will tell us where
is the pipe exactly okay and then we
picked up the pipe so this is the uh the
the the reflection of the pipe here and
it was not very deep it was been kept
shallow so we avoided this area and we
dig the trench over here only in this
portion and this is this is the the part
which is marked here after the
topographic Corrections so pipe was way
below the scarp and then we open up the
trench and you can see that it exactly
matches what we see in the uh GPR
profile we also did 3D uh of this area
and that that helped us uh in
identifying that which portion of the
region should be um excavated uh for
more U better to get better information
okay that also was been done okay so
these are the multiple uh like profiles
which we were able to cut and slice in
vertical section okay then another
exercise we did in the AR at the
archaeological site uh um in humayun Tom
Delhi and this is close to the nudin
railway
station so uh uh I probably I'm having
few slides of this but the the
information which we got and what we
they wanted us to do is they say that
this is the the Monumental structure
here in the center and at a particular
location uh they were having the in
earlier they were having the enclosure
wall okay so they're like in boundary
wall but now there is no signature on
the surface so that was another um aim
which they asked us to do okay uh so uh
we started our survey and at some
locations we were able to pick up uh the
uh the signatures of that okay so this
is what we found is from the uh like one
of the survey which shows that this
there is a platform here and then uh
probably there is an water pathway so
what we we we found was that there is an
platform um and uh on either side and
probably this we interpreted as an water
pathway uh and these are most common uh
features in mugul gardens mainly and we
were also able to fix up that at what
depth we are able to see this and like
up to 2 2.5 M or three and below that we
don't see the structure okay what we
were we have marked the platform and all
that okay and similarly so this is what
our interpretation is and this is
usually has been seen uh in most of the
gardens okay in in which which were been
constructed by mul okay so there will
been pathway in between and all that so
probably this uh is indicative of that
okay now about the enclosure wall as I
told that they gave us the distance that
at what distance uh probable enclosure
wall would be there but on on Surface
there was no indication so what we've
did we planned the survey like that
considering that if the wall is uh move
in this direction then we should have uh
the reflections if we cross the Wall at
this particular portion okay but this
was again and tentative measurements
with that gave okay so we did GPR and we
were able to pick up a clear indications
of this hyperbola and flat uh plate and
then uh sloping Reflections okay and
this was not only at one location all
profiles what we did we were able to
pick up this but this was not enough for
us so we tried with 3D and we were able
to see clear indication of uh prominent
Reflections that indicated that this is
a wall structure uh which extends uh in
particular direction and and the depth
so we interpreted that this is an
enclosure wall which they wanted to
identify and this goes up to 1.5 one 1 M
or so and around 2 m we were able we
were not able to see that
actually so this is how so this could be
in this type of enclosure wall would was
there in the past
okay now uh another part we were also
able to pick up the crisscross
relationship of of the structures
because one we were able to see here
this is the wall structure here but
another one was here okay so next
interpretation if you see that is what
we have marked okay so uh probably this
was the another wall along with this
lump uh wall or maybe the brick bads we
we see here so might have collapsed and
that is one of the reason that why we
see this crisscross again we were able
to see at the depth that it doesn't
extend okay now the last one uh part
which I would like to mention here was
iatra and in a chatra we did at multiple
locations but one of the locations here
where we did outside the Fortified
structure anatra is an very old ancient
site uh which flourished till uh 1200 to
1300 ad and uh so here we did outside
the the structure and the the the the
initial Pro without processing the raw
profile we were able to pick up
something like this but after processing
what we saw is an a Very clearcut uh
depression here and the and with that
the excavation was been done and you can
see that both were been compared so this
this is the the feature you see over
here okay so this is what uh the best
you can do with the GPR uh uh and you
applying for different because it is a
non-invasive technique you don't need to
go for digging uh initially but at least
you can Mark precisely your utilities
and the structures which are uh present
subsurface okay so with this I will end
this lecture uh and uh
more you will learn during the Practical
okay so lab part which we we will do we
will record that now one more lecture uh
which uh will I'll be uh giving will be
on the OSL dating part and that again
will be followed with the by the lab
okay so till then goodbye Take Care
thank you so
[Music]
much
[Music]
[Music]
[Music]
