You can replace your front door handle set in just a few minutes and use basic tools. It’s fast and easy - let us show you how!
#frontdoorknob #handleset #schlage #kwikset
Buy your DFJ T-shirt, Cap, or Coffee Mug at https://www.dirtfarmerjay.com/shop
You may want to change your front or exterior door handle because you want a new look, or the unit is wearing out and not performing dependably. That’s why we made the change - the unit was wearing out, and would lock us out from time to time, even though we had unlocked it from the outside and went out the door to water plants or get the mail.
We put off the replacement simply because of frugality. The switch should have been 4 or 5 years before to match the bronze-colored electronic “keyless” deadbolt that was installed just above it. Brass and Bronze don’t play that well together, but somehow we got used to it.
Our lockset of choice is a good consumer brand, Schlage®. Pronounced “SCH-leg” you can verify this by visiting their video on pronunciation:
https://youtu.be/NCuxMXW6U6s?si=FATk4xe9LeQYYDNs
While we believe the Schlage® brand is of higher quality than other brands we’ve found in home improvement centers, the way that different brands are installed on your front door is essentially the same.
There is no loss of face by reading over the instructions for your particular handle set to see that any idiosyncrasies of your handle are addressed and that installation goes smoothly.
Here are some common facts related to doors themselves any good manufacturer will address this by having their product be adaptable to various sizes.
To start with, U.S. doors are typically 1-⅜” (35mm) or 1-¾” (44mm) thick. Our experience is that most exterior doors are 1-¾” (44 mm) thick, but could be slightly thicker. So, make sure what you buy can be installed on your door.
Next, is what is called the backset. This is the distance from the edge of the door to the center of the hole where the lockset or door handle will be installed. The two common sizes in the U.S. are 2-⅜” (60mm) and 2-¾” (70mm). Most good handles can accommodate either.
Next, is the distance down from the center of the main mounting hole for the handle and latch, to the bottom hole where the bottom end of the handle will be attached to the door using the bottom bolt. This can vary a bit. Adjustability comes in handy here as well. The Schlage® unit adjusts from 8-⅜” (213mm) to 9-⅞” (251mm). Handy!
You’ll only need a medium-length #2 Phillips screwdriver to do this remove and replace. You can use a cordless drill-driver, be sure not to overtighten if you do. Easy does it!
To replace, work from the edge in and from the top down. This will keep things in place until you remove them.
Remove the two screws that are holding in the latch/backset assembly. Then remove loosen the two screws that are adjacent to the interior handle, remove the interior knob or lever, and set it aside. Remove the through-bolt at the bottom of the handle while holding the handle on the outside (this avoids having it drop off the door) and then set it aside.
Now, remove the latch/back-set.
You now have a “clean” door to install the new unit. Simply reverse your steps, but don’t tighten fasteners until everything is installed. Install the latch/backset first, taking care to orient the tapered side of the latch correctly, that is, towards the outside of the house.
Now install the outside handle, but don’t put the bottom bolt in yet. Align the posts and the blade that operates the latch, and slide them through the backset. Then place the inside knob or lever and align the blade and screw holes. Place the screws in from both sides of the base of the inside knob or lever and tighten them enough to hold the whole assembly together. Insert the bottom through bolt, and thread it into the decorative fastener on the inside of the door, but leave it loose.
Do a final check to see that everything is aligned and operates properly. This includes the latch extending and retracting its full distance, the thumb-lever presses down completely and extends and retracts the latch properly, and the inside knob or lever operates correctly and rotates back to the neutral position without any binding.
Now tighten each fastener, checking for proper operation as you do. Over-tightening in any area will likely cause binding. So, if something doesn’t operate smoothly, loosen the fastener for that area of the handle set slightly to see if it will solve the problem. It most likely will.
Explaining the process seems lengthy, but this entire process takes about 5 minutes. It’s that easy.
JUST DO IT YOURSELF!
Instagram: https://www.instagram.com/dirtfarmerj
Facebook: https://www.facebook.com/dirtfarmerjay
[Music]
hey direr J here from direr j.com well
it's come time to replace that front
door handle maybe you've been putting it
off because you just thought it would be
really tough or take a long time well if
that's the case I've got good news for
you we can change out one of these and
about 5 minutes stay tuned and I'll show
you
[Applause]
how hey dirtfarmer J here from
dirtfarmer j.com well this front door
lock uh or handle is actually started to
give up the ghost a bit here it's been
around for a long time and as you can
see a long time ago we put an electronic
lock but it just wasn't a priority get a
match and you know we kind of got used
to the brass and you know antique brass
look but now this has started to become
problematic doesn't operate correctly
and uh from time to time if we go out
even though we've just unlocked it from
the inside cleared it go out we come
back we find that it's locked itself and
we're outside trying to get back in our
own home so now is time to change it
there's just a few things you need to
know but you can get this change down in
about five minutes uh once you get the
right door lock now that brings me to my
second point and that is the door latch
that we like to use is the slag brand
and that's how you pronounce it if you
go up on their website you can go right
to a video that we've got at the bottom
uh linked to their website pronouncing
their name which is slag now there's a
lot of discussion whether that's the
real way it ought to be done in German
but that's what they call themselves
enough of that let's just look here and
see that this particular set is designed
to pair with a deadbolt so this one
includes the interior door knob on the
side plus an exterior door but is not
key like this one is so this needs to
absolutely be keyed uh for for or
actually installed with a uh another um
lock or dead bolt otherwise you've got
an unsecure door but you get the point
here now there's a couple things you
need to know before we jump in just as
far as range of sizes if you get this
part right when it comes time to
purchase it at the store then when you
get home that 5 minute installation is a
reality if you get the right thing so
you need to know a couple things about
some of the measurements on the door
let's move move on to that and I'll show
you what those measurements are by the
way just to let you know whether or not
you're installing one with a key lock in
it like this or the one we're doing here
which is a passage style uh the
installation is about the same the time
wise so it'll go very quickly but there
are actually a couple Dimensions you
need to know on the door so first of all
the distance from the center of where
the knobs going to go the hole where the
knob is to the edge of the door is
called the back set and most of the
locks you can buy especially the kind of
set that I just bought or perhaps quick
set or others you're going to find uh
that they have a back set of either 2
and 38 in which is right at 60 mm or 2
and 3/4 in which would be further back
uh or right at 70 mm so you need to make
sure that whatever the distance is for
your door from here to the edge was as
in the is within the range that you want
to purchase uh your door handle for your
latch okay the second thing you need to
know is the distance in the center this
way right here down to the bottom
attachment knob down below and the range
of that it those are usually somewhere
around 9 in uh the schle model that we
just were showing you has a range of 8
and 3/4 uh in which is 213 mm uh up 2 9
and 78 which is 251 mm now you don't
need to write all this down it's in the
description below you just go down there
and see all this information but you
need to make sure that the handle is
going to fit the hole that you've got
there um the third thing you need to
know is the thickness of the door now
standard exterior doors in the United
States typically typically come in at 1
and 3/4 in right here uh which is 44 mm
roughly interior doors are generally
around an inch and 38 uh in which is
about 35 mm um but most exterior doors
you're going to find and the sets that
you buy from will fit on a 1 and 3/4 in
or 45 44 mm door right here so here we
go we've got that now that we know those
Dimensions there now it comes time to go
ahead and remove the old lock set as far
as tools go this is really simple I like
to use a driver drill although I use it
just gently
so that I don't overd dry or strip out
screws and that is a number two Phillips
tip or if You' just like using a manual
a regular old screwdriver there you go
number two the other thing that you'll
likely need is a very small uh flat
screwdriver uh to remove one of the um
vanity covers that's down below on the
bottom hole there which we'll show you
in just a moment so simple tooling but
the first thing we're going to do is
open the door and remove the screws off
of the back set here we go here's the
latch right here so we're just going to
go ahead and take these screws
[Music]
[Music]
out just leave the back set the latch
loose
go ahead and close the door again all
right let's just pop off this
[Music]
cover and when we do we can see that we
have a screwdriver or uh or screw there
that the screwdriver can be used just to
[Music]
remove it's a fairly long bolt because
it needs to go through uh the 1 and 3/4
in door there to the other side so now
we've taken out two of the set of
Fasteners and the third ones are right
here on both sides of the lat so we're
going to carefully open this and we'll
go ahead and remove those now I like to
use this long drill simply to get past
the knob if you have a lever style it's
a little easier but because the knob is
kind of the way you can't just take the
driver and put in straight you have to
go in an angle and you just just lightly
remove those so you don't strip anything
out all
[Music]
right okay those are completely removed
now let's go ahead and move out the door
handle well that one's still got a
couple threads left on
it
all right that whole handle has now come
off this side we can now pull off the
outside there's the
outside and now we can push the back set
of the latch out now you have a stripped
door that is ready to go and boy it's
cold outside so we better get this job
done now we're going to reverse our
steps with a new set and this will go
very speedily okay the new set here
simply opens
up
inside you
have a
handle the inside handle there's the
outside handle ready to go some good
packing inside of this box right
here you can see that we have our new
latch our back set you have a nice set
of instructions right here with good
pictograms so this keep out of trouble
if you're actually doing one that has to
do with uh having a a keyed lock here uh
that'll walk you through it usually
these instruction sheets are for various
models and that's the case with this one
from slag and then of course here's the
inside uh door laps or door knob and
again you've just seen that so let's
reverse our steps the first thing you
need to do is put the back set in now
make sure you put it the right direction
as you notice there is a
taper on that so you want this taper
side to go to the
outside not to the inside otherwise
it'll hit the strike when you go and
close it the strike is this part on the
jam okay so what we're going to do is
put the taper to the outside go ahead
and slide that in place it and then what
we're going to do is go ahead and just
put a couple of screws but not drive
them home all the
way
but not quite all the way
home I like to keep things a little bit
loose so at the end you have room to
adjust things so right now if I close
this uh then I'd have a little trouble
open I have to pull it back here so
we'll just leave it partially open like
that then we're going to go ahead and
take the exterior handle
which here it is it's ready to go we're
going to put it through notice there is
a square shank and that matches a square
opening here in the back set
so I'm going to put it right
through and I'm going to adjust the
plate on the bottom so that the part
goes through the door and then there we
go now I'm able to hold it on
there and it actually will hold itself
there let's go ahead and put on the
second side the inside and thread the
long screws
in because this is a passage
lock there is no
um turn or anything like this that to
lock it or engage it that way so this
simply goes on here and you'll see see
right behind you to the door latch is a
little hard to see with this light and
the color of this Hardware but there's a
screw hole that goes right through here
that's going to allow these screws we're
putting in to line up directly and
engage the other side and hold it tight
here we
go you will need to finesse these screws
a little bit to get them to line up but
once they engage then simply line up
your plate in the back here so it's not
running not parallel to the edge of the
door line it up and then go ahead
and tighten the top first just don't
over tweak just bring it on
home there it goes we'll H we'll really
tighten it in a
moment okay let's do a test run let's
just
see Yep this works
well the door latch outside works just
fine it's in place we'll need to put the
scw bolt here in just a moment all right
since this is working well and latches
just great we're going to go ahead and
tighten these
now doesn't take
much okay there that
is all
right and I'll hand tighten the rest
just so I can
feel how tight I'm getting it that's
good that's good as well all
right all right we have a nice latch
here now comes time to go ahead and put
the throw bolt down at the bottom and
take care of that and then put a cover
on it as well all right go ahead and
insert the bolt in find the thread on
the other
side
all right let's drive that on
home got a good solid connection on both
sides and now install the decorative
rosette that is there to cover that all
up that just goes on with th pressure
and
now this side of the door is done the
next thing to do is just put on the
strike plate that takes a few moments to
adjust and there you have a complete in
installation that only took a few
minutes now obviously it took a lot
longer to explain this than it did to
install it this used to be my job a long
time ago of installing Hardware at the
very end and you could literally open
boxes and had Fasteners set up and you
could have these done in 5 minutes
including the stripe plate and adjust it
and go on to the next one uh both are
EXT exterior interior doors now if you
really would like to know more
information check out the description
below where we give you all of the links
but we also tell you about some of the
measurements that I called out earlier
well now you know how to do this simple
job another great thing that home owners
need to know those would have trailers
and many of you do well from time to
time you're going to need to rewire
those lights well here's a video that we
showed you how to wire them correctly
what wires what color wires go where and
while you're at it check check out this
other video that YouTube has chosen from
our catalog that they think is perfect
for you and we think you'll enjoy it too
hey thanks for tuning in until the next
time this is dirtfarmer J from
dirtfarmer
j.com