Lecture 14 - Transceiver Architecture - I

IIT Roorkee July 201
61 followers
Jan 25, 2024
Concepts Covered: Aim of Receiver Design, Basics of Heterodyne Receivers
[Music]
[Music]
uh welcome once again to RF transer
design course uh we were discussing the
basic of noise and linearity
nonlinearity in the last module uh so
this module will be focused on the
transer architecture so which is very
important as far as this course is
concern we'll try to uh cover all the
architecture conventional and modern
which are used in current RF systems uh
that we are going to discuss in this
module so let's start we'll start from
the receiver architecture because uh we
have a very small signal that we want to
recover and then we will move to the
transmitter architecture so both
transmitter and receiver architecture we
will try to cover in this
modu so before going to the uh receiver
architecture uh if we try to uh observe
that what are the goal or what are the
aim of receiver design so I I just want
to give one example let's say uh your
signal which is coming is very small
signal it is around -90 dbm if you try
to convert that minus 90 dbm of signal
it will be a
microvolt so uh our aim is to
reconstruct the information out of the
that very tiny
signal and we have already seen that
that weak
signal that is coming it is already
corrupted so much and we want to recover
the complete
information so the first aim of any
receiver design is a
amplification so there should be
sufficient
amplification so that your signal which
is coming which will be Amplified enough
now uh if we if we take the example of
ADC if we just connect directly this ADC
to the antenna so this ADC if we
directly connect to the antenna it is
getting very small signal and ADC
requires very higher input signal so
that it can convert into digital because
we want to uh perform the all the
modulation demodulation into the digital
domain so ADC requires very higher input
signal but we are getting very small
signal from the uh atmosphere or any
channel we are getting very small signal
and we need to do the amplification so
the first aim is a
amplification now here this uh LNA is
kept first because it is going to
amplify the signal now why it is called
as a LNA because it should amplify the
signal but make sure that it will not
add much noise into the system so it is
a low noise amplifier so
our our LNA should be as it should add
very less noise so that there is a
degradation in SNR will not be that much
what it means we already have seen in
the last module that we should have a
low noise figure of LNA and we have also
seen the freeze formula what it says
freeze formula that if your first
component is adding a less noise and it
has a sufficient gain then subsequent
stage noise contribution will be less so
complete system required a first stage
should be Amplified so in receiver
design the basic aim is
amplification and as ADC because we are
getting a signal in
microvolt ADC if you see it's LSB or
offset or input repair noise it at least
requir the uh voltage in terms of molt
so it should amplify the sufficient gain
there is also requirement of a high
dynamic range
why it is high dynamic range let's say
right now I am far from the base station
so if this is my uh base
station let's say if I will make a
cell
and if this is my base station and I am
at this location at the periphery of the
uh cell then the power that I'm
receiving is very weak so very weak
Power is coming and that weak will be
around - 90 or - 100 based on the
standard that we are using so this weak
signal now this weak signal is going to
come to your receiver so at that time
you you are getting
amplification now as you as you are
moving towards the base station and if
you are somewhere here very near to the
base station the amount of power that
you are receiving is
high so let from - 90 it might reach to
the 0 dbm so - 90 to 0
dbm so you need around 90 DB
of dynamic range means your uh input
might range from very small signal to
the very large signal compared to the -
990 dbm so this range can also not be
captured in the ADC and uh if LNA is
adding the gain then amount of uh signal
amplitude that is coming to ADC will
vary so that is also one of the issue
when we are using a this architecture
where only LNA and ADC will be used so
there is a challenge here that is a
dynamic range
another thing is this architecture is
not uh help help us because your
sampling rate you're you are going to
give the very high frequency signal
Omega RF which is very high and you need
to have a higher sampling rate in your
ADC so the this architecture in this the
first aim is amplification that we
understand but is it a sufficient no it
is not sufficient so now we are moving
to the second aim of a receiver design
what is the second aim that is a
variable gain because there is a high
dynamic range you need to have a
variable gain
amplifier just after the
LNA so because of requirement of high
dynamic range as I explained it might
range from 0 to 100 DB you required a
variable gain
amplification and here Ed generally ADC
detection range is limited for example
60b per bit and if you go for higher
amount of Beats number of Beats if you
are increasing in order to consider this
entire dynamic range then your power
consumption in receiver will increase
and we always try to optimize the power
so that our device will last long in the
battery because we are talking about the
mobile
devices so power consumption is
increases if there is a number of bits
are increased so we need
to we need to use variable gain
amplifier in this so that our
uh there should be sufficient dynamic
range that we can cover so this variable
gain amplifier should add a low
gain or it should add a high gain logain
when there is a when we are very far
from
the far from the base
station and it should give High
Gain low low gain when we are near to
the base
station when we
are
near from the base station and High Gain
when we are far from the base station
because uh if you are far your amp your
received received signal is in minus 90
dbm so it should at least add sufficient
gain and why we are adding the low noise
amplifier because it is uh let's see if
it is giving a 20 DB of gain then
another another 60 or 70 DB gain you can
get from the variable gain amplifier and
this can be varied according to the
where where exactly how much power you
are receiving so there there should be
some feedback mechanism also after the
reception so that you can able to the
change the variable gain automatically
and that is also called the
automatic uh variable gain amplifier
so it will automatically
tune as you are moving or you are far if
your signal is corrupted so much and how
much amplification you are getting that
is a called a
automatic uh gain amplifier or automatic
variable gain
amplifier but what is the challenge here
the implementation of VAR variable
gain uh amplifier at RF frequency is
challenging because you require re ired
that much bandwidth and with the
bandwidth uh you required to change the
gain so that requirement is sometimes
difficult to F fulfill so in order to do
this there there might be variable gain
amplifier can be kept after the ADC
means or after we uh do the down
conversion we'll also talk about the uh
third gain of the third aim of the
receiver and interfering signal limits
the sensitivity so if there is a very uh
let's say there is a weak
signal if there is a weak signal and if
we have provided very high gain then
there is a possibility that your input
power is due to the blockers or
interference will be high and that might
limits your sensitivity so uh first aim
of receiver is to
amplification in order to consider the
dynamic range second a of receiver is a
variable gain now we'll move to the
third aim that is a down conversion this
is very important as far as RF receiver
design is concerned the down
conversion we if we try to work at very
high frequency and your ADC and all
other component s required to uh tune at
very high frequency then your power
consumption will go exponentially high
so in order to reduce the power
consumption we always try to work do the
digital demodulation or uh base band all
the base band we will try to work at a
low frequency so baseband frequency are
lower compared to the RF frequency
and the all the base band processing we
will do at a lower frequency so that our
power consumption will not increase and
we we can do the efficient demodulation
in the base band so always the part
which is a front end so this is called a
front end where where you employ the
down conversion up to the down
converting of the signal and let's say
up to the ad see it will be mostly
called as the front end and the moment
you have converted the
data to the digital then it will be
called as a basement so all the RF
receiver consist a RF front
end
and it is also called
if
backend we'll also discuss about the I
frequency and all in the upcoming slides
so here it reduces the power consumption
and uh if we are transmitting then it is
up conversion and if we are receiving
then it is a down conversion so we need
to up either up convert the signal or
down convert the signal according to it
is a transmitter and receiver so here it
is a down conversion so let's say if
your frequency is a 2.4
GHz your carrier frequency Omega C is
2.4 GHz and then you are down converting
to the Omega if which is a 100
mahz so you required a sufficient L
signal that is in this case Omega loo is
around
2.3
gahz so it can be how the down
conversion we will do this is called a
multiplier and this multiplier or mixer
it is called mixer or multiplier this
this is a uh widely known as a RF mixer
which will down convert the signal from
The High Frequency to the low frequency
when low is applied so it is it is a
three port device it has a RF input it
has a lello input and if that is a
intermediate frequency which is a output
so it is a two in put and one output so
what mixer generally what mixers do
mixer translate the frequency when you
multiply two signals which is Omega 1
and Omega 2 or Omega RF and Omega lo you
will get a two product Omega RF minus
Omega Lo and Omega RF plus Omega Lo so
the for down conversion it is Omega RF
minus Omega Lo so the basic a of the
receiver is a mixer is translate the
frequency but however these mixers might
add much noise so it is a noisy the
noise figer will be range of 10 DB or if
you can also lower down to five or 6 DB
but this is going to add more noise
compared to the uh LNA and that's why we
uh most of the RF transceiver employs
the lowo amplifier before the mixer in
order to reduce the uh implication of
the noise of mixer so as per the freeze
formula we all all know that first
component dominate the noise so that's
why the first component we try to use a
low noise amplifier and in all the
popular architecture Ln followed by a
mixer architecture and it is a
popular it is uh almost everywhere in
our communication devices we are using L
noise amplifier followed by a mixer
architecture so the we have discussed
the first aim is amplification first aim
of receiver second of receiver is a uh
dynamic in order to mitigate the dynamic
range that is a variable gain
amplification third is a down conversion
so here after the
down conversion you can use a variable
gain amplifier and at high frequency it
is easy to use variable gain amplifier
in certain application there is a two uh
means uh one LNA can also add the it is
a to means you can add a switch LNA can
be work at High Gain
mode and logain
mode so you can use LNA at High Gain
mode or low gain mode or after LNA some
radio frequency amplifier we we has been
added and it will provide either High
Gain and low low gain based on the
switching so but it is not that much
variable gain at R frequency we try to
use but we can use either uh High Gain
or low gain mode in the low noise
amplifier and mostly variable gain
amplification or uh automatic variable
gain try to implement either in after
the if conversion or in the base band so
uh this are in the back and we try to
bring it to the digital level so this is
a thir uh three three aim of a receiver
design now we'll move to the fourth aim
that is a
filtering so what is the fourth aim of
reive design is the filtering why we
need a filtering because we already seen
the nonlinearity in the last module and
if there is a very high uh amplitude
blockers or interferers or gemers it can
have a different name it can be written
as a blockers or interferers or chamers
if it is coming in between then it will
desensitize your entire receiver so you
need to have a filtering so so that
unwanted signal will be pter filter out
so the first component in receiver uh
basic uh receiver design is a filter and
it can remove the out of band blocker
and compression let we already have seen
that if there is a more compression it
will uh reduce the SNR let's say if
there is a very high frequency blockers
and that this is a desired signal when
when you down convert there is a desired
signal and some
unwanted uh signal is coming and because
it is unwanted we will we can consider
it a noise so your
SNR output SNR is degraded so here your
SNR is reduced because of The Unwanted
blockers is it required a sharp filter
to suppress the unwanted and unwanted
signal or interferers or blockers and
the I already told that in standard it
is defined that what amount of blocking
you want to add in the receiver so it is
already defined in the standard that how
much 60 DB or how much inband and out of
band blockers that we want to uh
reject so what are the effect of block
Fus interfere or Jammers due to
compression the gain of the signal
reduce we already have seen noise figer
of the receiver as I explained noise
figer of the receiver
increases and because of inter
modulation it will lower down the
sensitivity of receiver because your
noise is increasing your sensitivity
will lower and if your noise is less
your sensitivity is improved
so these are the four aim of any uh
receiver design that you should keep in
your mind before going to any
architecture the first is a
amplification second is a uh variable
gain third is a down conversion and
fourth is a
filtering if you are going for the any
architecture or any uh receiver design
topology then you should keep the this
four aim in your mind so if this is
there you can also uh invent some Noel
architecture that you uh in future you
can do now let's move to the
further
topic so uh I already told the same
thing so this is much better it is drawn
here so in the transmitter trans
architecture in transmitter there is a
Power Amplifier band pass filter and the
signal will be transmitted now in
transmitter we do not need to worry
about the interferer so much because uh
there is
a we we can directly employ the band
pass filter and transmit the signal
however in receiver you have a you are
going to receive too many unwanted
signal and that you need to have you
need to consider while designing the
receiver so this is a requirement of the
filter at the transmitter also and at
the receiver also and in transmitter you
are removing the adjacent Channel power
and in receiver you are uh removing the
uh adjacent Channel or adjacent band
which you want to uh subtract so filter
is important as I have told in the uh
final aim of
receiver
so there are two kinds of filters are
possible one is a channel selection and
another is a band selection so uh here
what I just want to differentiate here
what is a channel and what is a band so
let's say you are working at a 900 mahz
and 900 mahz there are a different
channels each channel for example has a
bandwidth of 200 khz so it will employ
the different
channels and there is a a band which 900
MHz is a called band and inside the 900
MHz there is a channel now if you want
to down convert if you want to employ
the filter which will uh directly uh
down convert the complete Channel means
it will filter out the other channel
then your requirement of
Q is very high because your Center
frequency let's say Omega
not and your Q is inversely proportional
to the bandwidth so if your Omega not
frequency is 900
mahz and if your Delta Omega is 200 then
you you required the Q which is in terms
of very high value in in terms of in in
terms of Mega and that value is very
difficult that kind of filter is very
difficult to
design so however if you can consider
the complete band of let's say 20 mahz
or uh 200 mahz band and here it is a 200
khz so this Q requirement will reduce
and that kind of filter you can easily
design that is why we initially try to
select the band and then later on stage
we will go for the channel selection so
always there is a band selection will be
done first and channel selection will be
done later on so band selection is
followed by the channel selection and
that we should take it into the further
stage of the down conversion so this is
very important because of very high Q
requirement we are not uh using the
channel but let's say if uh for certain
application your band width is very high
and you do not have the that many
channel in the band you can also select
the band but make uh we need to make
sure that the requirement of Q is not
going very high so in this case uh
mostly because our RF bands are crowded
it has a different band has a different
application we have already seen in the
first class and because we want to
recover the signal very small Channel
out of that first we will try to select
the band and then we'll go for the
channel
selection we'll also uh have a uh we
already dis uh discuss about the full
duplex in the while we discuss about the
basics of wireless communication full
duplex what it means that you are going
to send a uh uh signal means transmit
signal and receive signal transmit
frequency is a different and receive
frequency is different and at the same
time you can transmit and receive if you
employ the frequency
division
multiplexing so uh here for duplexing it
is called Full duplex uh P duplexing
where you employ a duplexer how the
duplexer performance looks like there is
a transmitter band so this blue color
here is a transmitter band So for
receiver band it has a sufficient
rejection so you can see this 55 DB
Rejection it has so rece signal will not
come here at the only transmitter signal
will be transmitted however when you see
from the receiver side it has a uh it
will receive the signal uh and which is
at little bit higher frequency compared
to the transmitted frequency and it it
can also reject around 55 DB of the
signal to the uh from the transmitter so
this is how the
uh re uh full duplexing will happen and
this duplexer is widely used in order to
switch the this two
frequency so if there is a 55 DB of
attenuation still let's say if you are
transmitting the power of one wat you
have employed the duplexer still this 30
dbm if you reduce by 55
then that much power is going back to
the low noise amplifier so we need to
consider this is also called
the inside the band itself uh you are
getting the uh interference so there is
no interference which is coming from
other place but from the transmitter
itself you are getting the
interference and that should be uh we we
need to that's why employ the filter
here also which will we we also need to
employ the filter if it is a very high
power which is a going back to the
receiver so there are two kinds of
blocker one is called inband blockers
and another is called out of band
blockers so uh in this there is a GSM
standard example is considered so if
your transmitting frequency is 890 to
915 MHz we generally uh consider the
transmitter frequency lower compared to
receiver because the power consumption
will reduce if we have a lower frequency
compared to the because power amplifier
is a power hungry component so 890 MHz
to 915 MHz is a transmitter frequency
and 935 to 960 MHz is a your frequency
and this is a uh bandwidth of the
channel so if this is a desired
channel that is minus 99 dbm then you
you will have a little bit
high that is uh - 43 so this this will
be - 43 DPM so at if it is 900 mahz at
600 Kilz just at 600 khz you should able
to block the uh in channel inband
blocker which is a minus 43 dbm so if
there is a power of minus 43 dbm your
receiver should have a sufficient
linearity so that it will block and
while discussing the nonlinearity I have
already given an example of that how
much iip3 is required for your low noise
amplifier so that it then block the
blocker and you should uh also uh go for
high so at 16,600 KZ again it is
increased this is a requirement that we
have at three uh 100 khz or 3 mahz it is
minus 23 DB and this is called inband
because that is inside the band inband
blockers and then there is out of band
blockers this is a
at 20 MHz another band which is out of
band and it should reject the 0
dbm so this is a minus 99 dbm and it
should reject the Zer dbm of blocker so
this is what is defined in the standard
that what is the range of power for
blocking the inband blockers and how
much power level you that you need to
suppress and outut of band blockers so
your receiver should have a sufficient
linearity so that it can uh mitigate the
effect of the inband blockers as well as
out of band blockers and if it is
required you should add the filters in
order to remove the inband blockers and
out of band
blockers now we will uh go to the basic
uh receiver architecture that is a h
rodine
receiver in the hrod receiver uh if this
is a your input frequency that is Omega
ion and if we draw the both positive and
negative this is a plus Omega in and
this is a minus Omega in and when you
apply the Omega L that is uh here it is
uh represent presented as a sharp Delta
frequency Omega L then if you are adding
a mixer and after that if there is a
filter because mixer is going to give
you Omega
RF plus Omega L and Omega RF minus Omega
l so you need to filter out the uh
higher frequency component that is Omega
RF Plus Omega l so if we try to see in
terms of the spectrum what it will get
it is a plus Omega in minus Omega L plus
Omega in plus Omega
L at the other side minus Omega in minus
Omega L and minus Omega in plus Omega l
so I can also write this
minus Omega in plus Omega
L and minus
Omega L minus Omega in because it is a
negative side so if if let's say this is
a 2.3 GHz Omega in and if Omega L is a
2 uh if this is 2.4 because there is a
higher RF if it is 2.3
gahz
so you will have a signal let's say at
100
mahz - 100
MHz and the addition of this uh around
4.7 gahz and minus
4.7 GHz so you your signal which is down
converted in basic it rodine will have a
four
components which are Omega
Omega
RF minus Omega loo and plus or minus
Omega RF minus Omega L and plus or minus
Omega rf+ Omega
l so uh this is a rrod receiver we'll
discuss about rrod receiver much in
detail in the next class uh and all
other receiv architecture we'll discuss
in the next class thank
you
[Music]
ah
