How to do PLC wiring In this video we are going to learn how to do Any PLC wiring with a Relay Board.
To Buy any PLC, HMI, VFD, Sarvo Motor Etc Please Contact Simplex Syscon Pvt Ltd
Simplex Syscon Pvt Ltd is the Largest Delta Industrial Automation Solution Provider Company For the last Two years. Simplex Syscon offers Delta’s automation products and solutions with high performance and reliability, including drives, motion control systems, industrial control and communication, HMI, PLC, Sensors, and robot solutions. Simplex Syscon provide information monitoring and management systems such as SCADA and Industrial EMS for complete, smart manufacturing solutions.
For detailed information about Simplex Syscon Pvt Ltd : Please visit: www.Simplexsyscon.in Tel: +91 9811033465 Email: [email protected]
If we have to make a starter to start and stop a machine, then
we use this type of electrical
device to make the starter and the wiring of this type
of electrical device is
very easy,
but If I tell you that for the same machine
you have to use PLC and
complete the wiring using PLC, will
you be able to do the wiring?
I think
you will not be able to do the wiring at all using PLC.
You will not be able to do the wiring. The
reason behind this is that you think that the
wiring of that PLC is
very difficult and
you will not be able to do that wiring, but
friends, I would like to tell you that the
PLC is The wiring of PLC is
like this, which is a starter, it is
much easier than this, only once
you understand the concept, once you understand the concept,
you will be able to easily
do the wiring of any PLC, then
how can we do the wiring of any PLC? How to do it, let's
understand through this video, so I have
a small PLC here which is
made by DE company, now
using this PLC, we will
understand the complete wiring, see friends,
if you want. If you want to do wiring of any PLC,
then at the time of wiring, first of all you have to
see at
what voltage the PLC will operate, that is,
if we have to start that PLC,
then which voltage should we use to start it? If you want to provide power
supply, then what you have to do for this is
that if you
look at the side of the PLC,
you will find this type of terminal on the side. This
type of terminal
is written on the side that you have to pay here. Which
power supply has to be done and what
voltage power supply has to be done?
As you will see it is written here that 0
and 24 means that I will have to provide 24 volt power supply
here, that too
DC power supply. Now DC power supply.
For this, we use SMPS here,
so you will see that I have
SMPS here, in this SMPS it is
written l and n. On the terminal with L,
I have connected the phase supply here
and n. I have
connected the neutral power supply on the terminal 1, which means
that this SMPS has got the power supply.
Now the output terminal of this SMPS,
as you will see, it is written here that v
minus and v plus v minus give us negative
power supply. And from v plus we will
get positive power supply, then by taking both these
power supplies, we have to
connect them with the PLC. Now this PLC
also comes with this type of connector to provide power supply to this PLC. In this you will see that there is
a connector here,
we will take out this connector here
and after removing it, we will simply
connect it with the connector here, now this is the PLC, the
wires which are connected to this PLC. That
wire of ours is of three colors, as you will
see, there is a red colored wire here, there is a
black colored wire and there is a green colored wire.
Total here, there are three colored wires.
Now these three wires are these three wires.
We have to connect it with SMPS.
Here I have
SMPS. This SMPS will
give 24 volt power supply in my output.
To operate the PLC, 24 volt power
supply is required, that is why I
used such SMPS here. Which
converts 230 volts to 24 volts. Okay,
now the red wire here is
used for positive power
supply, black wire
is used for negative power supply
and green wire. It is used
to make connection with earthing. Okay,
so this is the red wire,
we will take this wire and the positive terminal of SMPS,
like it is written positive here,
then we will take
this wire with the positive terminal. We will connect the
green wire. After this, we will
take the black wire and connect it with the negative terminal.
Now this is the green
wire. We have to connect this wire with earthing
but there is
no earthing here. If it is there then I skip it
but if you want to make the connection then
connect this green wire with earthing. Now here is the
PLC, in this PLC you get two types of
terminals, one is The
input terminal is the second one and the output
terminal is as you will see in this PLC it
is written here that these means that the
input terminal is this one, you
can see in this PLC a total of eight signals we
can give here such as Take
this push button that I have,
if I press this push button, then
where will the signal go to, for that
we use the input terminal here, so
whatever is the input terminal,
on that terminal we have to The signal has to be given as to
what work we have to do, like
if I have to start the motor, then
if I press the start push button, then the input
signal should go to the PLC that we have
pressed the start push button,
similarly. If we have to stop the motor,
then the signal of the stop push button we
press to stop it will go to the input terminal.
Similarly, if you
connect a limit switch, its
connection will also be done to your input terminal
as well. If you have
any sensor, if you want to
give any feedback through that sensor, then we
provide the feedback on the input terminal itself. Now
after this, which is the output terminal, through this terminal
we get any electrical device
operated, let's say. At
present, I have this tower light. There are
three different lights in this tower light. If
these three lights are to be
operated in different conditions, then the
power supplied to these three lights will be the power
supply. It will go through the output terminal.
Similarly, if I have to
turn on a contactor, then the
signal that will go to turn on the contactor will
go through our output terminal or
any relay near you, if you have to switch it on and
off. So the signal that will
go to it will also go to our output,
that is, if we want to operate any device, then to make it operate,
we have to provide the signal through the output terminal. So, what is the
input terminal?
What is the output terminal?
Now you must have understood the
wiring here. You have to understand this wiring.
Friends, before doing the practical wiring of this PLC,
I would like to tell you that
if you want to buy a PLC, then
if you are in the market to buy the PLC. If you
go then you will not be able to get a PLC directly.
I currently
live in Bhopal city and I visited many shops in Bhopal city to
find out that if I can
get a PLC through which I
can explain to you then in a big city like Bhopal.
I have not found a single shop
where I can go and
buy this PLC directly, so if you also face such a
problem, then what should you do?
You can directly contact Simplex Sakan company and get the information as per
your
requirement. Tell the requirement,
they will
get every type of PLC of Delta company, you
want any type of PLC, you want HM, you
want BFD, every product
is available with them and the
price of the product sold by them is The
price is much lower than what it is in the normal market,
so I would
like to suggest you that if you
want to buy PLC SD or HM or
apart from this you want to buy any electrical product of Delta company, then go for it.
For this, you
can contact them directly. I have given the
contact number and address of the main distributor of the company
here on the screen.
By contacting them directly,
you can easily buy the products of Delta Company,
that too in the market.
Now let us understand the wiring here.
See friends,
if the PLC you have works on 24 volt DC power supply,
then in this condition
we can do the wiring in it in two ways. One is
sink type and the other is source type
wiring. What is sink source type wiring? Let
me explain you a little. Suppose you have a
lamp. You have this lamp. Now
supply power to this lamp.
Here you are using DC power supply to provide it.
Now this is the DC power supply
wiring. What you are doing in this wiring is that
you have connected your positive power supply directly to the lamp
and the negative power supply.
You connect the push button with the negative power supply,
then the power supply from the push button is
going to your lamp, then this type
of wiring is
called sync type wiring, which means that
if The PLC that you have, like
I make a PLC here, PLC
has two terminals, this terminal is called
s/s and this terminal is our
input terminal, that is, SO terminal,
like if you look at the PLC. So here, the
input terminal is
written on this terminal. Here s / s s / s
means that to
operate this PLC, we use both sink
type wiring and source type wiring. You
can do both, so here
we have to connect positive
power supply or negative power supply to the s/s terminal.
Now suppose
you have connected the positive power supply here,
then the negative power supply. The
signal has to be brought to x0 x1 We will
connect the power supply and
if we provide power supply through a push button on the terminal which is x0,
then this
type of wiring is
called sync type wiring. Now in the same
way if your The PLC nearby has an
s/s terminal.
You take the negative power supply to the power supply that will be connected to that terminal and
connect it directly to the s/s terminal. The
power supply
is here and the positive power supply is here, so
if you take the negative power supply directly and
connect it to the s/s terminal
and that is your positive power
supply here, along with this positive power supply,
you push the button. If you connect
it and after connecting the push button, you are taking
it and
connecting it with the input terminal you have here,
then we call this wiring as source
type wiring and DC power supply type wiring.
To make the PLC operate, we do two types of wiring.
Whichever type of
wiring you want, you can do it, there will be
no problem. Okay, now here
we have the PLC. If we
understand the wiring, then here I have a
PLC, I have to operate this PLC, so
as I told you, what
you have to do with the PLC, which is a
terminal with pay up s, as I told you
here. If I zoom in, here we have a
terminal with s/s, so the
first thing we do on this terminal is that we
take our negative power supply and
connect it directly here, in
this way I have called the negative power supply here.
Took the power supply and connected it to the s/s
terminal. Now after this
I have a push button, after
pressing which the
signal should go to the x0 terminal, so
what will I do for this? That I have a
positive power supply here, I will
connect a wire with this positive power supply
and by bringing this wire to the push button here, I
will provide incoming power supply to this push button. Now if
I If I press it, it will generate a signal
and this signal will
go directly to our x0 terminal, so
here we have
made connections to provide a signal. Now suppose
you have NC push button here.
Meaning, if there is a stop push button,
what will you do for wiring it? You will loop a wire from here and
provide incoming power supply to this push button. Then
what will you do by generating a signal from here,
which is the terminal of x1.
On this terminal you will provide the incoming power supply.
Similarly, if
you have a limit switch, like
I have made a symbol of the limit switch here,
this is our limit switch. So
through this limit switch, if we want to control the PLC. So
what we will do for this is
that we will loop the same positive power supply and
connect it to our limit switch,
then take the power supply from the limit switch to the
second terminal here which is the
input one. If we connect this,
we can connect a total of eight signals in this PLC,
three are already connected and
five and we can connect here,
so these are the five terminals. If
we want, we can connect the push button on this terminal.
Connect the sensor,
connect the limit switch or whatever
electrical device is there through which we have to
generate the signal, we
can provide the signal by directly connecting it here, so whatever
wiring is there, I can complete this wiring
practically. Let me explain to you,
see what we have to do for wiring,
which is our SMPS.
You will connect a wire with the negative power supply of that SMPS.
Now the power supply that will come from this wire will be
that power. By taking the supply,
you
will see in that PLC that there is a pay up s terminal. By
taking this wire, we have to
connect it with the terminal which is the sink source.
Now
to provide the input signal to this PLC. For this, I
use the push button here. Now
if you look behind this push button,
here I have one ANO
contact and the other one is NC contact. So the
first thing I do here is that these
two of mine There is a push button. These two push buttons have
one terminal each.
I short them together in this way.
After shorting, this wire here
is the purple colored wire. This wire is the
looping of the wire here. What has happened is that I
will connect it with this, which means that the positive power
supply will come through this wire and the
positive power supply that will come through this wire,
that power supply will go near both the push buttons.
Now here I will
take another wire. I will connect this wire with this ANO push button
and
what I do with the other wire is that I will
connect it with the NC push button here.
Now suppose that along with this ask button, I will give
you a And if you want to connect the limit switch,
then what you will do is that there is a
power supply here, by looping it once from this power supply, you will
connect it to the anode contact or common terminal of this limit switch, then the output will be
single. We have to take the white wire
which is our input terminal and
connect it with that terminal
like I tell you here that this
is our white wire and through this wire
I want to The
signal should come on this terminal which is
This is the gray
colored wire here, I connect this wire to the x1
terminal. Now this is the
pink colored wire here. Through this wire,
we provided the input signal
to our push button, so what do we do here?
What we will do is by taking this wire,
which is our MPS, which is the
positive power supply of this SMPS,
as if we had directly connected the negative power supply
and here, which
is the positive power supply,
we will take this wire. We will take it directly and
connect it with the positive terminal here. In
this way, at present, I have
only told you the wiring of two push buttons.
If you have other electrical
devices like light switch, sensor, then
they should be connected to each other. You will also connect in the same way, provide a
positive power supply and
bring that signal to its output signal and connect it directly here.
Okay, now let us understand
how we will do the wiring of the output terminal.
Suppose, Do you have
any lamp here? Let me create a separate page here
and suppose
you have a lamp here and you have to make this lamp glow,
then what will you have to do to make it glow,
which is the function of PLC. It
is a common terminal, which means that
you will have to connect the positive power supply to the c0 terminal,
and here
you will get the positive power supply on the y1 terminal, which
means that the output of that terminal is common. If
we get it on y1, then the
power supply will go through it to our lamp, that is, by
bringing the phase supply, we will connect it to the common terminal
and through the output terminal,
we will connect the lamp through that terminal.
Now to operate this lamp. If
neutral power supply is also required then we will
provide the neutral power supply directly to it.
Now suppose that you have
another lamp, here you also want to operate this lamp,
then you
can directly provide the neutral power supply here
and face it. Your supply will be from y2 terminal,
so I provide phase supply through y2 terminal here.
Now there is
no need to provide input power supply to the y2 terminal here
because the common terminal here is already ready.
Now suppose that this At the bottom of the terminal,
you get here c1 terminal, so
c1 is the terminal, whatever is the terminal at the bottom of this terminal
like y2, y3 terminal or
y4 terminal, whatever is their output,
you will get the output of this terminal,
meaning that Whatever power supply you
connect here, this power supply will be
available at this point. When your output is
generated here, then this output will be the power supply.
Through it, we
can connect any lamp or device
and We can provide them with neutral power supply, it is
fine in this way,
so here we are
providing input power supply. If we want, this input power supply
can be AC power supply
or if we want, it can be DC power
supply. You have the
option to use either AC power
supply or
DC power supply. Whatever
power supply you use,
your output will be generated accordingly.
Suppose you have used common power supply here. If you connect the
positive power supply of 24 volts to the terminal,
then connect it to the output terminal.
You will get only positive power supply on this output terminal,
that too 24 volts. So, take the
power supply of this terminal
along with the lamp. We will connect it in
this way. Now to make this lamp operate, we will
also need a negative power supply.
So, we will directly connect the negative power supply of your power source here
with the lamp
so that our lamp can start working properly.
Now, if you go to do the wiring of PLC practically,
then we always pay attention to one thing in wiring
that
we should not directly connect the load through the output terminal.
We use relay card to operate the load.
Meaning, there is such an electrical
device in which many relays are installed,
we operate all these relays
and through this relay, we
switch on or off any device, like if I have to switch on and
off this contactor. So
for this, first of all I will turn this relay on and off
and through this relay I will turn this
contactor on and off. Okay, so the
relay here, if we have to do the wiring of this relay,
then there
is a very simple way to do the wiring. Simply what has to be
done is that in this relay you
will see that it is written here + 1 -1 + 2 -2
+ 3 -3 + 4 -4, in this way the number
written here is + 1 and - There is 1 terminal,
this terminal is the first relay, which
means that if I want to operate this relay, then
I will
connect the power supply here, which means that the positive
power supply and negative power supply will come here and
connect to operate the second relay.
To make the relay operate,
we will have to provide power supply at the second terminal.
To make the third relay operate,
we will have to provide power supply at the third terminal.
Similarly,
if we provide power supply at the fourth terminal, then the
fourth number If the
relay is operational then this is the
terminal. The power supply on this terminal
should come through our PLC. So here is the
output terminal of the PLC. If we have to
do its wiring then what will we do?
This is our DC power supply. This is the
power supply. Which is positive of the supply, like suppose
here I have a positive power
supply, then I
will connect a wire through this positive power supply and
bring it to the common terminal of our PLC,
as you will see
here. It is written that c0 terminal is the
common terminal, so on this terminal we will
connect the positive power supply.
Now after this you will see that there are more
common terminals here like c1 terminal and
here c2 terminal also. There is a common
terminal, so if you want, you
can do looping of this power supply on this common terminal,
like I have looped it here, which
means that the positive power supply
will also come on this common terminal and here. Now
here is the second common terminal. If
I want, I can also connect another power supply on this terminal. For example, if I
want, I can bring the power supply facing the AC power supply here and
connect it here. Now this is the common
terminal, I will get the output of this common terminal at
two places, on y2 and on y3, so by
using these two terminals, I
can switch on or off a lamp, like suppose
I have this lamp.
If I have to get it operated then
what will I do? I will take the power supply from here and
connect it to this point and provide it with
neutral power supply directly. So
if a signal is generated from this terminal
then this lamp will glow
like this. By
looping a wire from this terminal, I
can provide power supply to another lamp or I
can provide power supply to a relay, then here my phase supply
connection is made. Now if I connect DC
power supply here. If I use a , then
through this also we will make the connection in the same way,
like by bringing the positive power supply, we have
connected it to the common terminal, now the
output of the common terminal is the output we
get from the y terminal, so from this terminal
we will make a We will loop the wire. Now
what will we do by taking this wire, we will
connect it to whatever electrical device we have to operate,
like at the present time, I have to
operate the relay card here, then what is the function
of the relay card? Here there is a terminal with coil,
like here there is a positive terminal,
so I will connect this wire with this terminal, then
if the power supply is generated from here, then the
first relay of the relay card is our relay.
Now I can make a connection
from here to provide power supply to the second relay
and by taking it,
I
will connect it with the second card here, now
to make this relay card operate. We will
also have to provide a negative power supply here,
so what I do is take the
negative power supply here and
connect it to the negative terminal of the relay card. I have done the looping here.
Okay, so you only have to
understand here that to make our relay
card operate, we will have to
provide positive power supply and negative power supply.
We will take the positive power supply from the output and
connect the negative power supply directly. I will do it,
okay, so the complete wiring which I have
explained to you,
we do its practical wiring, so
what I do at present is that I use the
DC power supply of my SMPS,
which is my relay
card. To make it operate,
if we have to make a connection to this relay card,
what will we do? This is a wire which
we will use for positive power supply. We will
take it and
connect it with our
positive power supply. Now this positive We will bring the power supply
and connect it with the common terminal of our REIL card. So on the
common terminal, I have provided positive
power supply here. Now I
will connect another wire on this common terminal.
We have looped this
wire and we will connect it to the second common terminal of this PLC,
like the common terminal of c1 here,
and then by looping another wire from there
and connect it to the second anode contact. We will also
provide the power supply through this wire. So,
we have
provided the incoming power supply to this PLC. Now the
output terminals of this PLC are
as written here: y0 y1 y2 y3.
These are all the terminals. Terminals are
output terminals through which
we operate our device by taking the power supply. For
example, if we want to
operate this relay card, then what will we do here,
which
is the terminal with y0 on that terminal. We will connect one wire,
like I have connected this wire,
now the signal that will go from this wire will go to
operate the first relay, so
what I do here is that this output
terminal means y0.
Bring this wire and
connect it to the positive one terminal here. Now in this
PLC, I want to operate the second relay through the y1 terminal here in this PLC.
So for this, I
use a wire here,
take this wire and
connect this wire with the y1 terminal here, in
this way, now the signal coming from this wire will be taken by
taking that signal. If we have to
operate the second relay, then the
positive terminal of the second relay here is
like I told you that
this is our input wire.
We are providing positive power supply in this wire,
so we have positive power in the output also. If we
get power supply, then
we will have to take this positive power supply and connect it with the positive terminal of the relay card. So, to
operate the second relay here,
connect it with its positive terminal.
Now, in the same way, to make the remaining
relays also operate,
we can make a connection through the output terminal of our PLC.
I will now
connect two relays and tell you.
If I have to operate these two relays,
then we will have to
provide negative power supply also, so
what will we do for the negative power supply which is
our SMPS, the
negative power supply which is coming from this SMPS, like a
negative power supply, we have here.
Another negative power supply is connected to it, it is
coming through this wire, so what will we do, by taking the same power supply
which is our negative power supply,
we will directly provide negative power supply to this relay card,
so for this I am here. I
use a black wire,
I will take one end of this wire
and I will connect it with the negative power supply of the SMPS which is my SMPS here,
where I will get the negative power
supply, as
if I Let me connect it here. Now
bring the other end of this wire and which is our relay
card here. Whatever relay we are using here on this relay card,
we will call that relay negative power here. Will provide the supply
directly, like what I
do here is that I
connect it with the negative tunnel of the relay card,
then from here I will do the looping of one bar
and the looping of this wire will be taken to the
other one here. There is a relay, I will provide
negative power supply to make that relay also operate,
so after doing so much wiring,
what we have to do is that which
is our relay, this relay
has N contact here, as you will see it
is written here. c1 o1 p1 c means
common, o means normally open and p means
normally close. This means that this
relay which has a common AO NC contact here, by
using it we
can operate any device like Suppose
you have a lamp,
you have to operate this lamp, it will operate
through our PLC, so to
give input signal to this PLC, we have
connected the push button here and
will press the push button. So what will the push button
do for us? It will give a signal to the PLC and the
PLC will generate our output signal here.
Now the output signal that comes here,
we are getting the relay card operated through
that signal. Now, using the relay here,
we will generate our We
can get the electrical device operated, like
here we have a lamp, so
what will we do to get it operated, there is an
anode contact here, through that anode contact,
we will provide phase supply to this lamp
and this lamp.
We can directly provide neutral power supply to the lamp.
Apart from this, what we have to do is that
we have to supply phase on the common terminal here. Suppose
our lamp
operates on 230 volts, then in this condition phase We will
bring the supply and
connect it with the common terminal and the
output of the common terminal will be N and NC. So
if you want AO then use N.
If you want NC then
use NC. At this time I have given
N here. I connected this lamp through a contact
and
I directly provided neutral power supply to this lamp.
Now if you have
another lamp and want to operate it too, then
you will make the connection in the same way for this also.
What will you do? You will
directly provide the neutral power supply to the lamp and the phase
supply will go to it through the anode contact of the second relay.
Now, if
you want, you can provide the power supply to the common terminal of this relay
from here or you can
If you wish, you can provide power supply here by using another power supply, in
this way you have to use the
NOC contact of the pay card here,
then
how do we do the wiring of PLC, I have told
you completely. Explained in detail,
what we have to do after wiring the PLC,
which is our PLC, we have to do
programming in this PLC,
our
electrical devices will operate according to the programming, now
how to do the programming of PLC, for this
I will make another video. I will
explain to you in complete detail and
friends, if you want to buy any PLC of Delta Company, then
you can buy this PLC directly by contacting this contact number. Let's
end the video here.
Thanks for watching this video.