Relay Logic जैसे Start-Stop, Interlocking, Star-Delta Fault कैसे ढूंढें और Wiring कैसे चेक करें 🌀 Motor Starters Wiring:
DOL Starter, Forward-Reverse, Star-Delta Starter Circuit Starter में कौन सा Component कहां और क्यों लगता है ⭐ Logic से कोई भी Circuit कैसे Design करते हैं और कैसे Control Panel तैयार होता है – ये भी सिखाया जाएगा!
Bottle Filling Plant Circuit Practice Two Air Compressor Auto Start Panel – Circuit Diagram बनाना और उसकी Practical Wiring करना ऐसे ही कई Real-Life Industrial Logic Projects के साथ Practice कराई जाएगी – जिससे आप किसी भी मशीन का Control Panel समझ सकें और बना सकें 📘 Drawing & Diagram Mastery:
══════⊹⊱≼≽⊰⊹═════════⊹⊱≼≽⊰⊹══════
किसी भी Electrical Drawing को पढ़ना सकें SFU Panel, HT LT Panel और out of india का भी Drawing को पढ़ना और समझना सकें Circuit बनाना और Field में Apply करना 🌟 1st Batch की झलक (May 2025):
पहले बैच में हमने 32 Powerful Classes ली थीं – जिनमें Wiring, Control Panel, Starters, VFD, PLC और Industrial Drawing तक सब कुछ सिखाया गया।
📊 Total Training Time: 50+ घंटे से भी ज्यादा Practical सीखने का मौका मिला – Real Circuit Projects के साथ।
🧠 Logic के साथ Circuit बनाना, Panel तैयार करना, Fault ढूंढना और Real Machine Wiring करना – ये सब सिखाया गया।
अब Batch 2 में भी यही Quality और वही Real Field Knowledge मिलने वाला है – बिल्कुल Step-by-Step और Live Practical के साथ।
══════⊹⊱≼≽⊰⊹═════════⊹⊱≼≽⊰⊹══════
🎁 Class के फायदे: 👉 Practical सिखाई जाएगी – Real Devices और Diagrams के साथ 👉 Engineer जैसी सोच और काम करने का तरीका सीखेंगे 👉 Control Panel, Machine Wiring और Fault Finding में Expert बनेंगे 👉 ISO Certified Course Completion Certificate मिलेगा
How to read electrical panel wiring diagram step by step
How to understand house wiring layout plan
Learn electrical drawing with practical examples
Best method to read electrical drawing for electricians
Electrical wiring diagram for home in Hindi
Friends, through this video, we are going to learn
how to wire a bar bending machine like this.
I have often seen that in my YouTube comment section
there are a lot of students who often comment
that Sir, how do you wire a bar bending machine like this?
Please explain a little.
Look, in this video, I will not explain direct wiring to you.
I am going to teach you the concept.
If you have a machine or a panel,
if you want to wire it, how will you do it?
As an example, if you want to wire any machine,
first of all, understand the working of that machine.
If you understand the working of that machine,
then you can wire it easily.
For example, the working of this machine is written here.
But let's skip this now.
I will show you a small video.
Watch that video.
So that you can understand the concept of how you will wire it.
Then according to that concept,
we will wire the entire panel.
So as you can see, this machine is our bar bending machine.
And here it is being used to bend the bar.
You will see one thing here.
Our machine has a disc in it.
I will show you in the picture now.
There is a disc in it.
It is rotated through that disc.
For example, a bar is placed here.
Then this disc is here.
When the machine is started,
it will rotate here.
And because of the rotation,
the disc will bend here.
Once the disc rotates in the forward direction,
the disc will bend here.
And after bending,
we will rotate it in the reverse direction again
so that we can remove the disc again.
So this machine is called a bar bending machine.
And we have to wire this machine.
You just saw a small video.
Now I will explain the actual working to you.
In this machine,
there are many buttons.
We operate it through these buttons.
To start the machine,
you have two options.
The first option is,
if you want,
you can press the start push button
and start the machine.
The second option is,
there is a foot switch here.
If you press this foot switch,
the machine will start.
After this, there are other functions.
Before understanding that function,
the machine will start
if you press the push button
or the foot switch.
So the first condition is,
pressing the forward push button
and the foot switch starts the forward contactor.
To start the forward contactor,
we have to press the forward push button
or the foot switch.
This is called the foot switch.
The machine should start if you press this.
Now you know the working of the contactor.
You also know that
if you give power to the contactor's A1 and A2,
the contactor will start.
Now you have to understand that
if you want to use this contactor
to make a circuit,
the A1 and A2 terminals
are the terminals
of this contactor's coil.
To give power to this contactor's coil,
we can make a symbol
like this.
What is this?
This is the terminal of the contactor's coil.
Here we can write A1
and here we can write A2.
In addition to this,
the contactor has NO and NC.
If you don't know the concept of
the contactor's NO and NC,
you can watch our previous videos
in which I gave an explanation
about the contactor.
At the moment,
we have to give power to this coil
to start this contactor.
For this, I will take a contactor.
What is this?
This is the symbol of the contactor.
We have to give power to this.
We have to give phase supply and neutral supply.
I will use a phase supply here.
I have used a neutral supply
What can we do with the neutral supply?
We can connect it directly
to the A2 of our contactor.
I am giving power directly
to this A2 terminal.
I have to give phase supply to this contactor.
Phase supply can be taken from here.
I will rotate it a little.
After rotating it,
we have to start it.
To start it,
we have to use the push button.
We have to make the symbol of the push button.
We can make the symbol of the push button like this.
This symbol is of the push button.
I will bring it here.
I will simply give phase supply
and connect it.
What will happen
if I give direct power here?
If I press the start push button here,
the contactor will start.
When I press it,
the contactor will start.
What will happen if it starts?
The bar bending machine will move forward.
But the problem here is
that the machine
will keep moving
until we press the start push button.
We have to do something
so that even if we press the start push button
and leave it,
the contactor will keep moving
and the bar bending machine will keep rotating.
To rotate it,
we have to make a holding circuit.
For the holding circuit,
we have to use the anocontact of this contactor.
This is my anocontact.
I will connect this anocontact here.
To connect it,
I will connect it from here to here.
I will connect this anocontact
parallel to the start push button.
If I press this push button here,
the contactor will start.
When it starts,
the anocontact will close.
When it closes,
the contactor will remain on.
What have we made so far?
So far, we have only
pressed the start push button
and made the bar bending machine
rotate in the forward direction.
But if it is rotating in the forward direction,
it will keep rotating.
Have we made a circuit
through which we can close the machine?
No.
We have not given the option
to close it yet.
To close it,
we have to press the stop button.
Suppose we want to close it
in an emergency condition.
What can we do for that?
We have to delete
the phase supply here.
After deleting it,
we have to press the stop button
or press the emergency button.
For that, I have taken
the emergency push button here.
I will connect this emergency push button
to the phase supply first.
Then the phase supply will go here.
If I press the start push button here,
the contactor will start.
If I want to close it,
I will press the emergency button here.
If I want to start it here,
it will not start.
Why?
Because I have pressed
the emergency button here.
I will release it and make it normal.
After making it normal,
I will press the emergency button
and it will start again.
The bar bending machine
is being operated manually.
When I press the start push button,
the bar bending machine will start
and it will rotate automatically.
It will not stop.
Now we will build the circuit
according to the condition of stopping.
But before building it,
we have made a circuit to start
with the start push button
and a stop button to close it.
Now let's understand what is being said
in the equation.
When you press the forward push button,
the forward contactor should start.
But along with it,
the foot switch should also be used.
We have not connected the foot switch yet.
Before connecting it,
let's take one more concept.
When the contactor moves in the forward direction,
there will be a bending limit switch here.
That limit switch will operate
and close the forward contactor here.
It means that
when I press this foot switch here
and start this machine,
or when I press this green button
and start this machine,
what will happen in that condition?
This disc
will start rotating.
And while rotating,
what will happen?
Inside this cover,
you will see a limit switch.
What is the limit switch?
This one.
This limit switch
will be installed inside
this bar bending machine.
So what will happen with this limit switch?
After this movement,
it will hit here
and the limit switch will operate here.
And as soon as the limit switch operates,
the contactor
which you are giving power supply to,
that power supply will be cut here.
To cut the power supply of the contactor,
a limit switch is installed
It is said to use that limit switch
here.
It is said that
when the bending limit switch
operates here,
the forward contactor should be turned off.
This must be clear to you.
And friends,
one more thing here.
When we bend
the bar bending machine,
we have to bend it
at some angle.
For example,
when you put a column in your house,
what do you do in the column?
We make a ring
like this.
If you want to make
a simple ring like this,
then you will have
a straight line.
But we have to bend this line
at 90 degrees.
For example, I bend it at 90 degrees.
This is 90 degrees.
If I have to bend it from here,
then it will also be 90 degrees here.
It should also be 90 degrees here.
Then I will bend it at 90 degrees here
and it will also be 90 degrees here.
It means that at the present time,
I have to bend this line at 90 degrees.
So what do we have to do
to bend it at 90 degrees?
We have to set the limit switch
at such a place that
as soon as it reaches 90 degrees,
the limit switch will operate.
To operate it,
this bar bending machine
has a hole here.
A pin is inserted
that pin will rotate
with this disc
and will collide with the limit switch
because of which
the forward contactor will stop.
Let me show you
We have to bend this line.
To bend it,
there is a hole here
and a pin is inserted here.
This pin rotates
and operates the limit switch.
You have to insert this pin
To set the angle,
you have to insert this pin
and you have to measure
the angle of the bend
in which hole to insert the pin.
But at the present time,
we have to understand the wiring.
How is the limit switch operating?
It is operating through this pin.
We have to connect it here.
To connect it,
we have to insert a limit switch
through which the contactor will stop.
The limit switch will be
the NC contactor.
Because we have to cut
the power supply here.
To cut the power supply,
we will use the NC contactor.
To connect the NC contactor,
I have to delete this wire.
I delete this wire
and bring the limit switch.
I give the power supply from here
and the power supply goes from
the output of the limit switch.
I have connected it here.
If you press the start
and push button,
the contactor will start.
The disc will rotate in the forward direction
and will hit the limit switch.
As soon as it hits the limit switch,
it will stop.
The machine
will stop here.
Now we have to return
the disc.
There is a condition for return.
Before that,
we have to use a foot switch
to start the forward contactor.
We have to start the circuit
through the foot switch.
To start the circuit,
we use the NC contactor.
We connect the NC contactor
to the parallel of the start
and push button.
If we connect it like this,
if we press the push button,
the contactor will start.
Or if we press the foot switch,
the contactor will start.
If I press any of these two,
the contactor will start.
The contactor will start.
Now I am pressing
the foot switch.
The contactor has started.
Now I am turning it off.
Now I am turning it on.
The contactor has started.
You must have understood this much.
Now we have to return
the bar bending machine.
To return the bar bending machine,
we have to bend it 90 degrees.
To bend it 90 degrees,
we have to take it back.
To take it back,
we have to use
a reverse contactor.
You know that
to start the motor,
we have to use a forward contactor
and to return it,
we have to use a reverse contactor.
In the control panel of the bar bending machine,
you will find two contactors.
One contactor will
run the machine in the forward direction.
The other contactor
will rotate the machine
in the reverse direction.
To rotate the disc
of the bar bending machine
in the reverse direction,
we will use a reverse contactor.
You must have understood this much.
Before explaining the next wiring,
I would like to tell you that
this class is a demo class.
Demo class means
I am going to start a live class
Electrician to Engineer live class.
This live class will be held daily
from 9 to 10.30 p.m.
In the evening,
you will come directly to me
and join the video call
and learn while talking to me.
The name of this class is
Electrician to Engineer.
In this class,
we will teach you
the electrical components
and how to build a circuit
using these electrical components.
For example,
I have taken a bar bending machine
and I have taken some conditions
for this machine.
What are the conditions?
Out of these conditions,
I have told you
that we have to start
the forward push button
or we have to start
a contactor by pressing
the forward push button
how to build a circuit
using the conditions given
In the same way,
I have given another condition
that the forward contactor
should be turned off
This is also a condition
and we have added this condition
in this circuit.
This condition is known as modification.
I will teach you how to modify it.
Apart from this,
the electrical drawings
that are used in the company
cannot be read.
Mostly, the electrical engineers
do not know how to read the drawings
and because of that,
they are not able to move forward.
If you still do not understand
the drawings of the electrical panel
as I am teaching you now
I am making a diagram here
How does this diagram work?
This is a simple diagram
If you are told
that if you are not able to read
the drawings of the L-T panel,
H-T panel, AC breaker, BC breaker
and if you are not able to troubleshoot
the drawings of the panel
then this live class is going to be
very beneficial for you.
This live class
is going to start from 21st July
which is going to continue daily
from 7 to 8.30 pm.
This live class
is going to start from 21st July
which is going to continue daily
from 7 to 8.30 pm.
In this live class,
you are going to be able to
connect with us through Zoom.
If you are not able to attend
the live class due to some reason
then in this condition
our live class
is going to run for 30 days.
Whatever I am going to teach you
which is going to be 1.5 hours long class
whatever I am going to explain
for 1.5 hours,
all those recordings will be uploaded
in our app.
If you go to play store,
you will get an app called
Electrical Technician
You can watch the recording of
the live class there.
The fee of this course is only Rs.18
But if you want to join
this course,
I have given you an offer.
You can see Rs.18 fee here.
But if I click on buy now
you will see a coupon code
ENG 200
Engineer 200
You have to simply apply
this coupon code here.
Click on apply
As soon as you click,
the coupon code is applied
and the fee is Rs.1600
That means
you are going to take training
from us for 1 month for Rs.1600
and that too daily
for 1.5 hours.
To join this class,
simply click on buy now
You can pay through coupon code
or UPI
and directly join the class.
If you want to know more details
about this class,
what all you will get to learn
we have already done a class
which is the first batch
This is batch 2
You can see the course details
of the first batch.
As you can see
the details of the first batch
Electrician to Engineer
If you see the content of this class
click on view
you will see the content
below that you will see
Electrician to Engineer all class
Here you can see the details
of the course
The class will start from zero level
We will start the class with push button
and the class will end
on the drawing
where you will see
LT panel, SV breaker, change over switch
We will end the class by reading the drawing
This is a very good class
You will get the time of every class
and what all you will get to learn
You will get all the details
If you want more details about the course
you can contact me on my whatsapp number
This is my whatsapp number
8989044606
You can message me on this number
I will give you the details of the class
I have given the link of this video
in the description
You can take the class details from there
You can join the class directly
I would like to tell you one more thing
As soon as you complete this course
I will provide you ISO certificate
You can make your resume
stronger by providing
I will provide you the certificate
of the one month live class
You can use that
and increase your value
If you want more details
about this class
If you want to join the class
The complete details are given in the video description
If you want to talk to me directly
You can call me on this number
and talk to me directly
Now let's come to our topic
The condition given here
In this condition
It is said here
When the forward contactor is off
The reverse contactor should be on
It means
There is a limit switch inside this bar bending machine
As soon as the limit switch is operated
The disc should rotate in the return direction
The condition given here is
When the limit switch is operated
The name of the limit switch is
LS1
As soon as the limit switch is operated
The machine should start rotating in the reverse direction
Let's make this
Now if we want to rotate this machine in the reverse direction
What we will do for this
We will use another contactor
This is my second contactor
I have to start this second contactor
To start this, I have to provide the neutral supply
I have given the neutral supply directly
Now I have to give phase supply to this
To give phase supply
What we will do here
I have to start this machine
only after the limit switch is operated
When this limit switch is operated
After that
This contactor
This contactor should also start
To operate this
Along with this limit switch
There will be another anode contact
You know that
Along with our limit switch
Both anode and NC contacts are available
What we are doing here
For this limit switch
We have a limit switch
Inside that limit switch
We will get an anode and an NC
I have used the NC here
We will use the anode here
Through that anode
We will provide power supply to this contactor
To provide power supply
We will use an anode contact
Now
I will provide power supply to this anode contact
From above
And from its output
Here you will think
Why did you provide power supply from above
Why not from below
I will explain this in my class
When we have to take power supply from above
When we have to take power supply from below
If I explain all this in detail in this class
The class will be very long
Maybe you will not like it
I am keeping this simple and short
So that you can understand it well
The other details
Like the concept
Why do we connect a wire here
Why is it being connected there
I will explain this region in my live class
In a good way
I have given power supply here
Now see what happens here
When I press this push button
My forward contactor is working
But when I operate this
When I operate the limit switch
As soon as I operate it, this one stops
This one starts
Means my reverse contactor has started
Because of which
My bar bending machine will start rotating in the reverse direction
Now it will keep rotating in the reverse direction
Is there an option to stop it?
Now when it starts rotating in the reverse direction
We have to stop it
To stop it
Now what we have to do
There should be some condition for it
So you understand one thing
Our bar bending machine
Along with that machine
There is another limit switch inside
As I said near this machine
There is another limit switch
What will that limit switch do
When this machine will go back
From where it started
Stop at the same place
Another limit switch will be installed here
Suppose
If your machine is in off condition
What is happening in off condition
This road here
Where is this road starting from
We will install a limit switch at this place
And what will this limit switch be called
This will be called our home position limit switch
Means
Its home position
Will be in normal condition at this place
So if the home position limit switch operates
In this condition
The motor that was running in the reverse direction
That motor should be off there
Apart from this
Another limit switch will be installed here
When will that limit switch work
When our bar bends at its angle
Suppose
If we have set it for 90 degree bending
As soon as it goes to 90 degrees
The limit switch that will be installed
That limit switch will operate here
What will happen when this limit switch operates
Our machine will start rotating in reverse direction
Apart from this
If you set it for 45 degrees
Then this limit switch will operate at 45 degrees
What will we do to do 45 degrees
We will have to put a pin inside the hole
In the 45 degree pin
Means we have to put a pin inside the 45 degree hole
Ok
So we can do it this way
So at the present time
We have to use the home position limit switch
Means inside this machine
Two limit switches will be used
One limit switch will be for angle
And the other limit switch
Will be our home position limit switch
So that if the machine comes in reverse direction
It will stop at the starting point
And not go beyond that
So for this
We have to put another limit switch
So for this
We have to take another limit switch
I will bring another limit switch here
Now the limit switch will be our NC contact
Because through this
We don't have to move forward in reverse direction
So I took this limit switch
Now through this limit switch
We have to cut the power of reverse direction
We don't have to cut forward
If you cut the main power supply
What will happen?
Both circuits will not be able to start
So what you have to do is
When this limit switch is operated
It will stop going in reverse direction
So in this condition
What we will do
We will cut the power supply from here
And I will put it up
I will delete it
So I deleted it here
And I connected it with this
Means the power that is going here
That power supply will go through this NO contact
In this limit switch
Then the power supply will go directly to our contact
In this way, a simple connection is happening here
First of all
The power supply from the emergency button
Went to this NO contact
And the power supply from this NO contact
Went to this NC contact
Now what is this limit switch?
It is a home position limit switch
Now let's see what will happen here
Our start push button is pressed
Our machine started moving in forward direction
What will happen after that?
As soon as our angle limit switch is operated
So this limit switch will be operated immediately
As soon as it is operated, it will start
Now what happens after it starts?
Our machine starts moving in reverse direction
And what will happen after going in reverse direction?
This home position limit switch will be operated
As soon as it is operated, it will stop
But there is a problem here
The problem here is
When you press the push button for the first time
Your forward contact will start
The machine will start moving
Now what happens after this limit switch is operated?
This contactor will stop
After it stops, this contactor will start
Now what happens after it starts?
The disk will rotate in reverse direction
As soon as it rotates in reverse direction
The limit switch will be operated and become normal
The disk will move again
And the angle limit switch will be operated
And the angle limit switch will move again
So after it becomes normal, this contactor will stop
After it stops,
Our machine will stop there
It means it will not be able to go back to its place
To go back to its place
We have to make a holding circuit
To make a holding circuit
What will we do here?
We will use an anode contact of this contactor
So for this, I take an anode contact
And I connect this anode contact
In parallel like this
And this anode contact should be of this contactor
So its name will be KM2
So here the number is 2
And here it is KM
This connection is done
You must have understood this much
Now let's see
Here I press the start button and the forward contactor is running
Now as soon as the limit switch is operated
The reverse contactor starts
Now as soon as the home limit switch is operated
After that, this contactor also stops
Now as soon as it stops
Our motor will be off
So in this way
Our limit switch will work
Now friends, here
We have made this circuit long
Now friends, here you will see
In this logic
Our machine
If it comes to the home position
Then the reverse contactor should also be off
Here it is written
If the home limit switch is operated
Then the reverse contactor should be off
Plus the machine should also be off
After that it is said
This cycle should always run
You press the forward push button
Or the foot switch
After that
Our limit switch will be operated
After that
Our forward contactor will be off
And the reverse contactor will start
After the reverse contactor starts
The home position limit switch will be operated
After that the reverse contactor will be off
After that the machine will also be off
Now this cycle will run again as long as you want
Apart from this, it is said
You have to use a selector switch
Through which you can select
Auto mode and manual mode
Auto mode and manual mode means
Here in this machine
Here the green button
We are running forward
If we press this button, we can run in reverse
But to run forward and reverse
We have to select
Do you want the machine to run
Until we press the button
Or we just press the button once
If we want this, we can make the circuit
Like if you want
If your machine keeps running after pressing
Then make that circuit now
We call that circuit non-inching type
And if you want to press the button
Until our machine keeps running
We call that inching type
To make an inching type circuit
In this machine
We will put a selector switch
Through this selector switch
We can select auto-manual
What will happen in auto-condition
If we press the button once
The machine will keep running
But if we put it on manual
What will happen on manual
Until we press this foot switch
Our machine will run
If we want to run in reverse
What will we do
If we press the reverse button
The machine will run
Until we press the button
For this, we have to make modifications
In our circuit
Now I have shown you a circuit
Now I am teaching you how to make modifications
In our engineering class
We are going to learn this
If you want to make a circuit
How will you make it
If you want to modify it
How will you modify it
If you want to add some other condition
According to that condition
What changes we have to make in the circuit
We have to understand everything
I am going to explain it here
I will explain it in my live class
At the moment
We have to keep the cable running
And turn it off
This holding circuit
Should work only on auto mode
It should not work on other modes
To make it work on auto mode
We have to delete this holding wire
I have deleted this wire
I have also removed the holding circuit
Now only
The push button is connected
The contactor will start with the push button
The power supply should go here
I have connected it from here
Now
We have to build these two wires
Let's see how it is built
To supply power to these wires
We have to use a selector switch
Here I have a selector switch
If I select this selector switch on auto mode
The holding circuit should work
If I select it on manual mode
The holding circuit should not work
What I have to do is
I have to remove the power supply
After removing it
I will supply power to this selector switch
Where should I supply power
Common terminal
The selector switch
If you see
Here you will find a common terminal
In which you have to supply power
After that
One terminal will be auto
And the other one will be manual
So
Whichever terminal you want to select
Auto or manual
You can select it
Right now, I just want
If I select auto mode
The holding circuit should work
For this, I have to
Connect a wire to this auto position
Now I will connect this wire
And supply power to this holding circuit
Means
The holding circuit
Will get power only
When I select auto mode
If I select this
Selector switch
The holding circuit will not get power
If I select this
The holding circuit will get power
But if I select manual mode
The holding circuit will not get power
Now this push button
Should always work
It should work in both auto and manual mode
For this, I have to supply power
I have to take the power supply from here
And connect it here
But the wire will overlap
For this, I will use the source arrow
I am making a source here
I have given the power supply from here
Source means power supply will go from here
This power supply will come through this
And this power supply will directly
Connect here
Source arrow
I will explain this in the drawing class
What is source arrow
Source destination
You will understand this
When you join the class
For now, I have connected a wire
From this point
I have to remove this
I have to connect this up
I have connected this up
After connecting, I will start
I have selected auto
I have pressed it
The contactor is on
The limit switch will operate
The reverse contactor is on
The home position limit switch will operate
Everything is off
Now if I
Select manual mode
What will happen
If I press the start push button
It is on, it is off
It is on, it is on
Until I hold the button
It is on, it is off
I have to start this reverse contactor
For that
I have to use the reverse push button
For that
I have to use the reverse push button
It is very easy
I have to select the push button
And connect it to this panel
From here the power supply is on
Now if I
Select manual mode
then I can press this push button and start the reverse contractor
and when I release it, it will stop.
When I press it, it will start. When I release it, it will stop.
So we have made a complete circuit diagram of our bar bending machine.
According to this circuit diagram, our machine will work properly.
But there is a problem in this circuit.
The problem here is that if you by chance
press the start push button to start both the contractors at the same time,
then immediately there will be 100 circuits there.
And to save yourself from 100 circuits, you will have to do interlocking here.
Why do you have to do interlocking?
Because you know that in this circuit diagram,
this circuit diagram is our reverse forward circuit diagram.
We have just added a lot of new things to it.
But the circuit is our reverse forward only.
Now in the reverse forward starter, we use two contractors,
but the motor is the same.
We start one motor with two contractors
and change the phase sequence of the motor's power supply through the contractor.
I have not told you the power circuit diagram here.
You already know that.
You can make the reverse forward starter power wiring diagram.
If you don't know, I will tell you in detail in the live class that is going to start tomorrow.
So use two contractors to start that motor.
The power supply of different phase sequences is going from both the contractors,
because of which there will be a chance of 100 circuits.
So if you don't want 100 circuits in your starter or machine,
then you will have to do interlocking for this.
And to do interlocking, you simply understand that
you have to connect the first contractor to the second circuit of this contractor.
Why do you connect like this?
You will have to explain the whole concept.
Similarly, the length of the video has increased a lot.
So I will explain that to you in the live class.
Or there are many YouTube videos where I have told you about interlocking.
You can watch that.
So to do interlocking, I will delete this wire now.
And I will connect the NC contact of this contractor here.
So I took the NC contact of this contractor here.
And I will bring it here.
And the power supply will go through this circuit.
And its output will be connected here.
This much work has been done.
Now here, the power supply of this contractor is coming.
In the middle of that power supply, the interlocking of this contractor has to be given.
So I delete this wire here.
After deleting, I will bring an NC contact here.
And I will connect this NC contact here.
So the NC contact of this contractor will be here.
And the NC contact of this contractor will be connected here.
Now I will explain to you the connection that I have done here.
Look, we have two contractors here.
In these two contractors, you know that the NC contact is given here.
So if we want to start this contractor,
then what will be the power supply that will go to it?
We will have a phase supply.
That phase supply will go directly to its A1 terminal.
So we will not go to this phase supply directly.
Now what will we do?
We will bring our phase supply first.
And in this contractor, the power that will go to this contractor's A1,
that power supply will first go to this contractor's NC.
Then the power supply from the output of this NC should go back to its A1.
So if you connect in this way, what will it be called?
This contractor here, this contractor is currently interlocked through this contractor.
If this contractor starts, then in this condition, this contractor cannot start.
Similarly, if you go to connect this contractor,
then the phase supply that will be given to it,
like I change the color here,
the phase supply that will go to this contractor's A1,
that phase supply should go through this contractor's NC.
That means what we will do,
we will take the phase supply here and connect it to this NC contact.
We will bring the power supply from its output by generating it from here
and connect it to this A1 terminal.
In this way.
So the NC contact that I have put here and here,
this is our interlocking that I have just shown you practically.
Now let's check the final connection.
As soon as you press the foot switch here,
our machine will start running in the forward direction.
After that, you will release this foot switch.
Because you will press this foot switch once and then leave it.
After leaving, what will happen?
Your machine will keep running.
What will happen while the machine is running?
Your limit switch here.
Which limit switch?
The limit one.
That means how much angle you have to bend,
that limit switch will operate here.
By operating it, the forward contractor will stop.
And if it starts reversing,
that means the motor has started rotating in the reverse direction.
Now if the motor is rotating in the reverse direction,
and in that condition,
if you press the foot switch to start this contractor,
or press the foot button,
then it will not start.
Why will it not start?
Because our contactor here has been interlocked through it.
Now what happened?
The reverse rotation started.
What will happen in reverse?
There is also a limit switch there.
Home limit switch.
So home limit switch.
Like where it started,
if the machine comes there,
then what will happen immediately?
This limit switch will operate.
By operating it, the machine will stop here.
And what happened by stopping this machine?
The whole machine,
your machine will be completely off.
If you want to start again,
you will have to press the foot switch again.
It started.
And when it starts,
in that condition,
if you press this reverse button,
then nothing will happen.
Your contractor will not start.
Because your reverse interlocking is installed here.
Okay.
So this is our complete circuit diagram.
By using this,
we can operate our bar bending machine.
Now this machine also comes of another type.
There are many such machines,
where to set the limit,
like your head,
to bend it,
you are selecting the angle.
Let me explain it to you properly.
See,
in this machine,
to set the angle,
we are putting a pin here.
But in many machines,
you get a selector switch there.
45 degrees,
90 degrees,
160 degrees,
150 degrees,
there is an angle like this.
Means it is written on the selector switch,
how much angle you have to bend the bar.
According to that,
you just select the selector switch.
There is no need to change the pin.
Change the selector switch.
According to that,
it will start working.
Now that machine,
how to wire that machine,
in all this,
my electrician to engineer live class,
which is starting from tomorrow,
I will definitely exchange in this class.
So if you join that class,
you will get a lot of knowledge.
So today's class,
before ending this class,
let me tell you that
tomorrow,
our date is 21st July,
on that date,
our live class is starting.
Electrician to engineer live class.
This live class is going to run for a month.
For a month,
I am going to provide you
the knowledge of engineering level.
The electrical panel,
the devices in that panel,
how to wire them,
what is their working,
if I say in that panel,
if you want to make any changes,
for example,
if I tell you in any machine,
put a timer in it,
if you want to turn off the machine
through the timer,
then how will you put the timer?
Which timer will you put?
Do you want to use the timer's anode
or do you want to use the anode?
If you use the anode,
where will the power go?
If you use the anode,
where will the power supply go?
The timer should always be on,
or the power supply of the timer
should also be cut.
There are many concepts
that will put you in confusion.
So all those concepts
are known only to the engineer,
and no one will provide you
But I am going to provide you
this engineering knowledge.
For that,
join this live class.
The live class will start tomorrow.
The live class that we will have,
will be from 8 pm to 9.30 pm.
I am going to give you a daily live class
for 1.5 hours.
And this live class
will run for 30 days.
So if you want to get
engineering level knowledge,
then you can join this live class.
The fee of this class is very low.
You only have to pay 1800 rupees.
You can only join the class
At the moment,
I have also given you a coupon.
If you use the coupon code ENG200,
then in this condition,
you do not have to pay 1800 rupees.
You only have to pay 1600 rupees here.
In this fee,
you will be taught in the live class.
Plus, the recording of this class
that will be taught in the live class,
you will get that recording for 4 years.
For 4 years,
the number of times you have to see the classes,
the number of times you have to do the revision,
the number of times you have to do the revision.
Apart from this,
if you do not want to join the live class,
you want to see the recording,
then the recorded class is also available with us.
You can also join the recorded class.
If you want to join the live class,
I have given its link in the video description.
Join from there.
Or write a live class on this WhatsApp number
and message me.
I will provide you the link.
If you want to see the recorded class,
its link is also given in the video description.
And if you want the recorded class link on WhatsApp,
then write a recorded class on WhatsApp
and message me.
I will provide you the link.
Join the class directly from there.
See you in the live class tomorrow.
At 8.30 pm.