Assembling an 18th Century Dial Clock - Weeks of Work Part 4

Legacy Conservatory
14 followers
6 Video Views·Jan 17, 2024
In Part 4 of the restoration of a lovely Verge dial clock by Weeks of London, I assemble the restored movement and see the first fresh ticks.
I've just marked up the position for the knife edge saddle and I've done that by centering
up with a straight edge, well square, and through the centre point of the pivot of the crown
wheel and I've marked up front and back, and then I could drop down with a small square from that
point up here to be sure of the centre line of the front pivot point. I'm pretty certain that the
middle location of these is the original pivot hole, so I think that's basically where it's
going to end up, but I will have to use a large-ish bush in amongst all of that mess to give it a
decent pivot surface. On the back cock itself, I will then scribe the, because I've got the centre
point, which as you can see is not actually dead centre of the back cock, but that is often the
case. I will then use a height gauge or something similar to take the height of the hole after I've
drilled it and transfer that to the back to give me the depth for the V of the knife edge. I've
set the height gauge using the front pivot point and got the height right. I'm now just scribing
off the back cock to give me the depth of the V of the knife edge. I've now got a scribe mark for
the centre line and a scribe mark for the depth. I'll go over to the milling machine with the back
cock and mill in the knife edge bed. I'm skipping ahead a little bit now, I've done a bit of work
off-camera on the escapement here. What I've done is to reinstate some pallet faces. If you
remember, I took some soldered up nasty ones off. I've actually put some nicer, neater ones on again
now. That was necessary. You can see on this side particularly, just in this camera shot,
if I get a little bit more light on it as well, you can see that they need to be slightly longer.
What's happened is the pallet flags have been filed down at some point and shortened. In order
to get the escapement all sort of back square again, those pallet faces need to be slightly
longer. That's what I've done there. I've also tidied up the escape wheel teeth where they were
a little bit worn on the tips. This is to get slightly tighter drops. It's just on the relief
side. I haven't touched the actual side that dictates the dividing of the wheel, but I have
just tidied up how sharp the tooth is, just on the relief on the back side of the tooth. In fact,
with this file, which I'm pointing at it with. This is a crossing file, but it works very well
for the relief shape of a tooth. With those things done, I've also made sure that the V
is on center line with the front pivot so that the arbor is straight, is parallel within the
plates. All those things together mean that now I've got a working escapement. Oh yes,
one other thing that you might have noticed is the pendulum rod is now made for it as well.
I tapped a piece of grass rod and that is riveted into the block. I now have a working
escapement. It's not absolutely finalized. There's a little bit of adjustment left and
you don't get a full impression just pushing it through with your finger like this. It's
the contract wheel so that it's end shake is correct and is meshing nicely with the pinion
of the crown wheel. Then that's the mechanical work on this clock complete. I've cleaned the
parts now of the clock movement. I had to do it off camera. I will cover a cleaning process in
video one day but for now I need to get this job finished. I didn't have the luxury of filming this
one. I have cleaned all the parts of the movement. Not to within an inch of their life. I'm trying
to retain color as much as I can. It's unnecessary to invasively clean and polish a clock like this
but I do like to have the dirt removed and have it mechanically as clean as I can. The next stage
will be to protect it. I'll wax the parts brushing on and buffing off with Renaissance
microcrystalline wax. Then it will be ready for reassembly.
The final stage is the assembly of the clock. The first thing I've done is just to put the
escapement together within the plates and that's to check that the crown wheel height is correct
and the adjustment screw is much easier to access while the clock is apart like this rather than
trying to fiddle around doing it later when the contract wheel is in. I can just put a small
amount of power onto the crown wheel to check that the escapement action is how we want it.
I've already had a little play with this and got it so that it's a nice compromise between having a
drop and risking topping a tooth. I think I've got it into a nice equilibrium. It's going to run
very nicely I think. So that done, I'll take this back apart again and we can reassemble the clock
the little extensions protruding of the pallet face to make them slightly longer. Much neater
than it was before and that's the fully repaired reinstated knife edge from the new Pendulum Rod.
And then you can see also the reinstated bed for the knife edge.
