noc18-mm11 Lec 36-Observation of dislocation contd...+ Dislocation Dynamics

IIT Kanpur July 201
20 followers
Dec 4, 2023
[Music]
[Music]
okay so we looked at one method of
dislocation observation which is surface
method where you do atching and then you
observe under optical micrograph and in
fact it's not all over let's see there
are a few more information about this so
when I said that it is useful for this
dislocation density less than 10 to the
power it should be 10 to power 10 meter
per square if it is more than that what
will happen what you would see is just H
bits lots and lots of H bits on the
surface so these what you would see is H
bits for example people have done study
in tungsten crystal and only when they
are far distant there is certain amount
of distance between them that you will
be able to resolve it and that's why
this method works best when dislocation
density is less than 10 to the power 10
per meter square now I only are
mentioned when I started this surface
method that this method has also been
used for studying dislocation motion and
what people have done is for example you
take when the dislocation density is
obviously when small you make a H in
somewhere and you observe something like
this and then actually it will be much
larger and let us say stress is applied
such that the dislocation is expected to
move in this direction so what will
happen is that the dislocation applied
some stress for a certain amount of time
and the dislocation has so here was your
so here was your original dislocation so
this is let us say t1 now let us say
some stress was applied for certain
amount of time and this dislocation has
moved so what will happen the same thing
you would observe over here
and then so this is at t2 and then let
us say Apple say you apply the stress
for some more time and then you may see
this over here so by and in fact what is
interesting is that you can even see the
remnants of the earlier dislocation
meaning what you would see over here it
would something look something like this
of because it is getting etched and the
dislocation on the bottom has vanished
so it will get a flat bottom and you
would see something like this so if you
have after the third time interval when
you etch it you would see a much larger
H bit over here but with a flat bottom
because the dislocation has moved out
and since this one moved out only
certain it's only a small time ago so
you would see a smaller H bit with a
smaller bottom surface and it will be
like this and only in this you would see
a sharp where it will be more like a
diamond shaped
indent into this and this clearly tells
you that the dislocation is present here
and it was present earlier here and it
was present earlier here and when it has
moved away you see a flat bottoming of
it and by measuring the distance and
know the time you can find out that for
applied given applied given stress and a
given amount of time how much the
dislocation moves you can find out the
velocity and other related information
can be obtained so this is one method
which is the surface method now let us
look at still another method which is
decoration method now remember that in
optical microscope dislocations cannot
be observed directly and therefore you
need certain you need a third material
to actually reveal it and this is where
decoration method comes into picture
so for example this people have done
study by doping so in potassium chloride
people have doped it with silver
chloride during the melt stage itself
okay so once it has solidified it has
some amount of very small fraction of
silver chloride present in potassium
chloride and then people anneal it
something like aging operation anneal it
to precipitate out silver precipitates
silver particles and where will it
preferentially precipitate obviously on
dislocations dislocation near the
dislocation core because that is the
large Valley free volume area where the
additional particles can easily come and
attach to we'll talk more about it in
the next part of the course where we
talk about plasticity aspect so silver
particles preferentially precipitate out
seller protocol's preferentially add
dislocations
and then it can be seen by can be
observed by optical micrograph
so what you would see is like let's say
there is a regular spacing of
dislocation so the dislocation maybe
let's say like this but you would not
have observed these dislocation lines
per se but now that there are cellular
precipitates so what will happen is that
there will be silver precipitates all
around this and you are not observing
the green lines when you look at the
look at it through the optical
microscope but what you would be looking
at these will be these orange particles
which represent here the silver
particles so you would know that this is
where the dislocation lines are present
so this is the decoration method which
is also used to find or to observe
dislocations next let us move on to the
most powerful technique which is
transmission
electron microscopy which is the method
which was used for the for the first
time to observe dislocation so note that
we are not saying any electron
microscopy so for example scanning
electron microscopy cannot show you
dislocations only transmission electron
microscopy can show you and that is
because transmission electron microscopy
depends on diffraction so near the day
wherever there is a dislocation the
planes around it get distorted and so
the diffraction takes place and that
diffraction is what leads to so for
example let's say there are certain
planes like this and this is your half
plane so the dislocation line is
somewhere over here and so let's say the
dislocation line is over here and your
beam is coming like this so the beam is
get coming in and getting deflected and
some of the beam which go Falls like
this will get deflected in a different
direction because of what is called as
diffraction vector we are not going into
the details of this transmission
electron microscopy because that is
course in itself but understand that
there is a diffraction vector and
wherever the planes are distorted you
get a distorted line and hence what when
you look at the image that is formed on
the bottom side where there is so the
wall all the lines come here but some of
them get diffracted and therefore what
will happen wherever there was
dislocation it will appear as dark lines
so what you would see is something like
this so let us say this is a thin foil
which is which has been observed and
that tin foil will have lines like this
what do these lines represent these are
dislocation lines so this is one of the
best methods to observe dislocation
lines and particularly if the density is
high so this word method works even if
so this method is useful whether density
is high or low
so transmission electron microscopy is
regularly used and even to calculate
dislocation density people use this
method so you can take micrographs and
over there you can count lines where you
are measured measure the length of the
lines to find out the density of the
dislocations so this is one method that
is regularly used another method which
is known to be used for direct
observation is x-ray diffraction
tomography
so this is a tomography meaning you are
taking x-ray defraction in
cross-sections
so usually a crystal is rotating and
x-ray diffraction czar done along along
the direction one particular direction
and it keeps rotating so it takes a
cross-section for all the overall
material overall system and then all
these images are integrated now over
here wherever there is a dislocation
something similar to TM wherever there
is a dislocation what will happen
wherever there is dislocation what will
happen what will happen is something
similar like I said in TM and over there
the intensity would vary so intensity
would vary and this can be directly
photographed
and in fact people have done this for
something like silicon crystal so in
silicon crystal people when we when they
have done x-ray tomography people have
seen images like this and you can see
this even in Holland bacon so all these
lines represent dislocation lines so
x-ray tomography because of the
difference in intensity is where
dislocation line is present what you
observe is a photographic image like
this which directly represents the
dislocations however the caveat here is
that this is also only good for low
density of dislocations
why because usually that different the
resolution of this tomography method is
very poor is very low compared to TM you
cannot compare it with TM anyways it is
orders of magnitude different so this
method is good only for low density
dislocations so now you can see that
there are so many different methods to
observe dislocation and you would also
realize that TM is the most powerful
method it does not matter what is the
dislocation density and you can measure
the dislocation density using this
particular technique so now we have
covered a lot of aspects about
dislocation so for example we have
covered stress strain what is the stress
strain field around a dislocation we
have looked at their elastic energy that
is told we have looked at different
kinds of dislocation whether it is edge
or screw we have looked at forces or
stresses that act on on the dislocation
which leads to their motion we have also
looked at interaction between
dislocation so if there is a large pool
of dislocation or like in a material
like if you're looking at a
microstructure there are several
dislocations and each one of them will
be influencing by or basically it has a
stress field because of which it will
cause influence on the other dislocation
so we have looked at it which was given
by the relation peach-colored relation
so this is the most important when it
comes to understanding the interaction
between dislocations or evolution of
dislocations we have also looked at
dislocation motion it takes place by
you know we saw that it can take place
by glide which is usually
room-temperature phenomena while there
is also a process like Prime which is
usually dominated at higher temperature
then we also looked at there is cross
slip which is possible particularly only
in the case of screw dislocation and we
also looked at look at the fact or we
found that there is a minimum stress
required critical resolved shear stress
or we can also we looked at it from a
domestically which is the polymer of
stress so there is a Perl nabarro stress
which must be overcome for the
dislocations to move continuously and we
also looked at intersection and we also
looked at strain strain rate and
velocity of dislocations so now having
and looked at all of this
there is now we are in a position to be
at least at the fundamental level
without talking about a specific system
because in when we talk about a specific
system which will come as the next stage
we can at least say how the dislocations
would react in the presence of others or
because of the presence of other
stresses and because of that will they
move how much they will move what will
be the final configuration where will be
the 0 energy configuration and this
study is called dislocation dynamics
so all that we have established so far
we are in a position to describe what is
dislocation dynamics all the important
elements that are needed for dislocation
dynamics are already been have already
been covered what we will what we need
to cover in later stages or to look at
dislocations in a particular system in
more depth
for example FCC BCC HCP or super lattice
structures which we'll come to in the
later stage so but for now let us
understand what is dislocation dynamics
dislocation dynamics it is study of
evolution of dislocations under internal
or external stresses
so this describes for example there are
dislocations but their dislocations will
be applying stresses onto other or four
end which will result in forces onto
them
or because you are applying stresses
externally because of which there will
be there will be forces or again on the
dislocation and then they will it should
cause motion of the dislocation so we
should be able to play using if you are
if you know all the values that is
stress strain per lever all stress and
we know the velocity strain strain rate
all these concepts we have then we
should be able to using the dislocations
the information or dislocation we should
be able to predict phenomena like pileup
what is pileup will come to about in
more detail but it is just the
dislocation getting accumulated at one
place when you apply stress now when you
apply stress what is happening
everything that is happening is
understandable in the constant in terms
of concepts that we have given over here
so this is where dislocation dynamics
come into picture
whatever phenomena that is observed
should be we should be able to explain
or in fact even predict or simulate
using the concepts here so what is the
governing equation over here the
governing equation is F equal to Ma
there is some force acting on to them on
to the dislocation because of which it
should accelerate meaning it should move
so these are the two important for the
important terms that we have over here F
and ma now let us look at it in more in
a greater detail what is the force
relation that we have if you remember
the force relation is already with us
which is known as the peach color
relation where we had written like this
and now I will put sigma a sigma net
meaning the overall stress that is
acting on to a particular dislocation
dot b
cross E or you whatever you want to
write so force part is already known to
us now a can be written as D to X by DT
square so we can say F is equal to M D
to X by DT square but there is also some
amount of resistance to the motion of
dislocation and where does this
resistance comes from come from if you
remember that we talked about when we
talked about the velocity that there are
damping forces so this damping forces
can be related in terms of B and it is
proportional to V and the velocity so
this will be FX I - BV and in fact we
should not write this term so the MD - X
by DT square which is the M into a force
is equal to some force which is acting
on individual dislocation - the
resistance force because of damping and
now if you look at this relation it is
very similar to the drag relation if you
are X we have been exposed to this
concept the drag force the drag velocity
relation so if a body is allowed to fall
freely in the gravity then there are
several forces acting on to it the
gravity force and then the buoyancy
force and then there is also a drag
force and because of that eventually a
body attains terminal velocity so drag
fellows it is similar to drag velocity
and hence what you should expect here is
that a terminal velocity will be
achieved
and what is more is that if the damping
force that is B if it is large then
terminal velocity is reached much more
sooner VT is reached much sooner so in
effect we and we know that damping
forces are very large so in effect what
it means is that we can assume to begin
with that the dislocations have attained
a terminal velocity so to begin with we
can assume that terminal velocity has
been achieved
so let me write down this equation over
here mm D to X by DT square is equal to
F X I minus B now we have to say BV
terminal and if the body has already
it's not a instantaneous velocity it is
V terminal therefore it means that M D 2
X by DT square is equal to 0 which means
that this whole thing is 0 so this
becomes 0 and therefore this relation
further boils down to velocity terminal
for the IH dislocation is equal to F X
when we say I we are denoting the IH
dislocation FXI by B or this can be
written like 1 by as if 1 by B is
another factor times F X so whatever
force is acting on to this into this
factor 1 by B which is now which can be
at many places it is written like M or
the mobility factor so this now this
mobility is something that we have not
touched which is unknown quantity but
this is also experimental quantity so
this is something either that can be
obtained from experiments or if you are
doing simulation you can assume certain
values which are appropriate for the
given condition and here vti if you are
doing assimilation then this vti can be
broken down to X I t plus delta t minus
X I T by delta T is equal to m FX I so
now we have set up an equation where all
you need to know is what is the force
that is acting and you can make certain
assumption about this mobility so you
need to you need to know you assume
then you optimize this parameter delta T
and this is something that you will
begin with some initial guess guess and
here you will so if you have some
initial - guess you would get the final
value of x I after one step T plus delta
T so this will be equal to M FX I into
delta T plus X I T so this relation now
allows you to calculate new position of
a dislocation given that you know what
is the force acting on it which we
should be able to calculate based on
what are the stresses being created by
other dislocation and once you have the
stresses being created by the
dislocation you just need to use the
peach color relation which will give you
Sigma dot B cross C so you will know the
force acting on to this and you will
have to make some assumption regarding
mobility and you will need to have an
initial guess for what is the initial
position once you have the initial
position for T equal to 0 you can keep
iterating it to get next and next and
next and next position so they say this
way how the dislocation is moving or how
the shape changes are taking place all
these things you would be able to
predict using this relation so in this
particular one this is this can be a
very simple problem by assuming very
simple by making lots of assumption or
you can make it much more accurate and a
little bit more complex by adding
complexities like you can add that there
is there has to be a pearl number of
stress for the dislocation to move
you can say that the dislocation they
will move out only on certain planes
which are slip systems
you can say that there are mixed
dislocation as well as edge and screw or
you can say oh that only edge
dislocation is there so all this will
make it more accurate and more complex
you can add image forces that will act
on the dislocation and there are several
other parameters that you can add over
here so for example the budget vector
and so on so this is this is not an
exhaustive list you can keep adding
different level of complexity to get a
more accurate result and this is this
system or this dislocation dynamics
method is frequently used to understand
the behavior of dislocation under
different conditions and in different
materials so we will this with this
introduction to dislocation dynamics
we'll leave it here and when we come
back next time we will talk about two
systems one is the FCC and one is the
BCC so we'll introduce we have only two
hours left we'll talk about FCC and BCC
and then we will end this course thank
[Music]
[Music]
[Music]
