noc18-me58 Lec 17-Force and Moment Resultant (part-II)

IIT Kanpur July 201
20 followers
Dec 3, 2023
[Music]
[Music]
hello welcome to advanced composites
today is the fifth day of the ongoing
course of the of this course which is
into its third week and what we will do
is we will today have a very similar
discussion on lines which we had
yesterday yesterday we had developed an
expression between force resultants and
midplane strains and curvatures today we
will develop a similar relation between
moment result ends and midplane strains
hand midplane curvatures so we will
again use the similar mathematical
process but we may not necessarily go
into that greater detail because the
basics have already been developed
earlier but we know that moment
resultant is what it is equal to
integral of sigma times z times DZ
right this is the basic expression now
essentially these are three equations
there is an equation for Sigma X there
is an equation for Sigma Y and there's
an equation for tau XY and this integral
happens between the limits minus H over
2 to H over 2 where H is the thickness
of the plate but we know that Sigma
vector is what is nothing but Q bar
vector and it changes from one layer to
a layer because the material is changing
so we have to talk about gate layer so
for Caitlin Sigma is like this
okay so we plug this back into this and
eventually we get for moment resultant
equals
cube R times epsilon naught DZ plus
minus H over 2 H over 2 cube R so
actually this K subscript should be
outside and there's a Zed here times the
curvature vector DZ and because this Q
matrix is discontinuous across different
layers so I will integrate within a
layer and then as I move from one layer
to other layer I will sum up things so I
can write it as M vector is equal to so
there should be Z here and there's a Z
square there so it is a summation K is
equal to 1 to n cube R is constant over
a thickness and strain is constant over
the entire thickness times integral of Z
DZ HK minus 1/2 HK plus summation K is
equal to 1 to N cube R for the Keith
layer times curvature vector times
integral H K minus 1/2 H K Z square DZ
so if I do this and I add up all the
terms then this entire thing we have
already defined as a B matrix which is 3
by 3 but now we have a new term
involving Z square DZ integral
and which is this and this gives us a D
matrix and this is also a three by three
matrix okay so we say that the moment
resultant vector is equal to the b
matrix times the mid plane strain plus a
d matrix which is again three by three
times the mid plane curvature and we
have already defined the b matrix so we
will not do that again but we will
define that d IJ is equal to summation
of q IJ for keith layer x HK cube minus
HK minus 1 cube into 1 by 3 overall we
can say so we can assemble all these
relations for moment and force
resultants
and we can say that force resultants and
moment result ends they are what they
can be calculated from this large set of
relations so you have mid plane strain
vector and mid plane curvature vector
and this is a matrix B matrix P matrix
and this is D matrix and all these are
also vectors of size 3 ok so this is a 6
by so these are 6 equations and this is
a 6 by 6 matrix
okay
so this is what I wanted to discuss now
now that we have developed relations for
these we will give these matrices a B
and D some names so the a matrix is
called extensional stiffness matrix okay
the B matrix is called bending no I'm
sorry it is called coupling stiffness
matrix and the beam at D matrix is
called bending stiffness matrix so we
will spend the moment trying to
understand why we these things have been
given these names so consider a case
that we have a situation where B is 0
where B is 0 if B is 0 then n can be
calculated if we know a and epsilon only
we do not need to know K essentially
what it tells us is that a matrix helps
us define how much the material extends
by stretches or gets compressed
particularly it gets compressed and in
presence of stresses extensional
stresses and extensional strains and
similarly similarly the d matrix
influences how much the system bends if
the D matrix values are extremely large
then the bending will be very small and
vice versa so that is why it is bending
stiffness matrix and the B matrix is a
strange creature it is a coupling matrix
and what it tells us is that if B matrix
is not 0
then if we try to stretch if I apply
just a plate if I have a plate and I am
just trying to stretch it and if B
matrix is not zero then the material
will not only get stretched but it will
also Bend and similarly if I try to bend
the plate and if the B matrix is not
zero it will not only Bend but it will
also get stretched so that is why it is
called a coupling matrix so so this is
the understanding behind the
nomenclature the next thing what we will
do is we will discuss in next few
minutes how do we provide names to
different lamination sequences so
nomenclature
for lamination sequences so suppose
there is this is the midplane let us say
there are several layers and let's say
what I will do is I will put their
angles here 45 minus 45 0 90 90 90 0
minus 45 45 okay and we will just so
these are the orientations and we assume
that thickness is thickness and material
is same for each layer if that is the
case if that is the case then we can
designate the lamination sequence of
this so we always start from top and we
go down so we say 45 and then there is a
minus 45 next to it so we say plus and
minus 45 we will just rectify this I
think I had drawn it or correct but then
suppose this is the lamination sequence
then these two are plus forty five and
money is minus forty five so I write
plus forty five and minus 45 then there
is a zero Degree layer so I separated by
a slash and then there are four ninety
degree layers but this is the mid plane
this is the mid plane and mid plane is
passing through this thing so I write
ninety and then all other layers are
just mirrored because this is the plane
of symmetry so I just say symmetric in a
long way this this if the moment I write
s essentially what it means is that the
lamination sequence is plus 45 - 45 0 90
and there are two layers above the mid
plane so this is 92 so 90 90 this is the
mid plane 90 90 0 minus 45 and 45 this
is what it means ok so we will very
quickly write down some rules so
whenever we express it such a format we
assume that we say that each layer
orientation is assigned with respect to
x-axis so this x axis does not change
it's a universal axis then we use these
as separators between layers
we always go from top to the bottom
what else if there are two layers next
to each other and they have the same
orientation so adjacent layers with same
theta then we give a subscript if the
laminate is symmetric about mid plane
then we use a subscript s and we can
also use plus theta minus theta this can
also be written as plus minus theta
similarly if the lamination sequence has
a negative theta and plus theta then
this can also be written as minus plus
theta okay so these are some broad
principles through which we determine
lamination we prescribe lamination
sequence the next thing we will start
discussing is role of a 1 6 a 2 6 B
matrix entire and D 1 6 and D 2 6 these
elements
okay now detailed discussion on these
elements we have already had in our
earlier lectures in the introductory
course but for purposes of completeness
and just a quick review we will discuss
these things and explain their influence
so what does a 1 6 & a 2 6 do a 1 6 & a
2 6 these two elements couple
extensional strains
with shear stresses and they also couple
shear strains with
extensional stresses so what does this
mean it means that if B matrix is zero
in such a situation suppose you have a
system when a 1 6 and a 2 6 are not 0
and then in that case if you subject the
plate to a pure tension stress it will
exhibit not only extensional stresses
but it will also share and if you expose
it to pure shear stress it will not only
get a shear strain but it will also
experience or exhibit extensional
strains so this is about a 1 6 & a 2 6
okay then the B matrix B matrix it
couples
extensional strain with moment result
ends okay and it also couples bending
response with force result ends okay
so what does this mean in plain words
that if the B matrix is not zero and I
suppose pull the plate then the plate
will not only get stretched but it will
also Bend and if the B matrix is not
zero and if I try to bend the plate and
if B matrix is not zero then it will not
only bend but it will also get a
stretched or compressed so that is why
it is a coupling matrix and then when
finally we look at D 1 6 M D 2 6 so both
these terms the couple bending curvature
with
M X Y so M XY is a twisting thing okay
so it bending curving and they also
couple twist curvature with MX and my so
what does this mean so just to show this
suppose I have a plate and I try to bend
it yet I try to bend it and if d16 and
d26 is not 0 it will not only Bend but
it will also do this type of thing
twisting and if I try to twist it it
will not only get twisted but it will
also do this thing bending so it couples
bending and twisting responses of the
system so d16 sent due to 6r of this
nature so this is the overview of this
all abd matrices and something special
about some of these particular members a
1 6 a 2 6 the B matrix and D 1 6 and D 2
6 and tomorrow we will have some further
discussion on these terms and we will
learn how to make these elements 0 or
minimize these values so that concludes
our discussion for today and I look
forward to seeing you tomorrow thank you
[Music]
[Music]
