We are thrilled to share with you our very first money-making project using the xTool S1 40w Diode Laser. Prepare to be amazed as we unveil the game-changing possibilities and profit potential of this groundbreaking technology!
Unlock your creative potential and start making money with the xTool S1 40w Diode Laser today. Don't miss out on the opportunity to witness firsthand the remarkable achievements that await you in the world of laser engraving. Subscribe to our channel now and stay tuned for more inspiring videos, insightful tips, and captivating projects that will take your laser game to new heights!
FYI: We are not professionals, and we don’t claim to be. This is what we found worked for our project. Yours may need a little different approach. We have just enough woodworking skill to make some basic furniture. Safety first!
FTC Disclaimer: This is not a sponsored video. All opinions are genuinely our own. This post may contain affiliate links and we earn a small commission if you make a purchase after clicking on my links. It doesn't cost you any extra. Thank you for your continued support to keep Making It!
Is the new X-Tool S1 40 watt diode laser as powerful as a desktop CO2 laser?
What is up?
Welcome back!
Do you like to do it, build it, or make it?
So do we!
And we have new videos each week.
This is the new X-Tool S1, the world's first fully enclosed 40 watt desktop diode laser.
Now when we first got this laser, I really wasn't sure we needed another laser, especially
a diode laser, and I really didn't know what we were going to use it for.
Oh, we do need more lasers, and I'll figure out how to use them.
Well now we know.
We know how we're going to use this laser, and we want to show you and tell you all about
it in this video.
If you're new to lasers, or you're looking for a powerful, flexible desktop machine,
this might be the one for you.
This machine has swappable laser heads.
It has a 40 watt diode laser head, can be swapped to a 2 watt infrared laser head, or
a 20 watt diode laser head.
This thing has all of the safety features.
It's fully enclosed, it's got the green tinted glass so you can still see your project, it
has the lid open safety feature, it has the tilt and impact safety feature, it has an
emergency stop button, and then it's got five fire safety sensors.
All starting at a $2,200 price point.
What I was most interested in was the power and the cut area.
This thing is 30 inches wide, 22 inches deep, 7 inches tall, and she's a petite of 44 pounds.
The cut area is 19 and a half by 13, but if you add that optional automatic conveyor
system you can cut 19 and a half by almost 10 feet long.
It also works with the RA2 rotary tool as another accessory so that you can do tumblers.
So the first thing that I notice, no camera.
I thought all desktop machines came with a camera these days.
But what it does have is a dual point positioning system.
It'll measure the top right corner, the bottom left corner, and it'll know exactly the cutting
area size that you're working with.
This thing does have autofocus.
It's similar to the larger machines except it resets every time so you'll be able to
autofocus on your material, even do 3D.
It uses a pen to measure the depth of your materials so it allows you to do curved surface
engraving.
Setup only took about 30 minutes.
I just had to remove some stoppers from the rails, install the laser head, add the hose
to the back, and then I added the optional air assist to make even cleaner cuts.
So for that I just plugged in the power cord to the back of the laser and an air hose into
the back of the laser.
I was up and running in about 30 minutes.
I started with the sample project that X-Tool provided.
I used the 3mm birch that came in the sample materials pack with the machine.
I followed all the directions and all the settings.
I wanted to understand how that dual point positioning worked as well as the autofocus
head.
I followed all the instructions as written and I got this little cute phone stand here
in about 10 minutes.
Now for what we've all been waiting for.
Will it cut ¼ inch MDF?
Well we're going to start by making a test cut card.
You should always make a test cut card.
That way you'll know the best settings for that material.
We're going to start at 80% power and work our way up to 100% power.
We're also going to start at 5mm per second and move up to 10mm per second and figure
out what's the best setting or if it will cut this ¼ inch MDF.
I am impressed.
You could knock me over with a feather.
I did not expect to see this many empty circles.
I thought maybe 3, but wow.
I mean I was getting through at 8mm per second.
What's that 85% power?
I could probably push this 80%, I did, I just pushed the 80% power running right out.
I'm very impressed.
I am so impressed.
I was also super impressed.
I thought we were going to be at 5mm per second, 100% power, but no.
I think.
With that said, 9mm per second just fell out.
I think you could get away with 9mm per second at 100% power, but man, yeah, shocked.
It really did a great job.
This is all one pass.
Have you seen our 3D door corner video?
Well those have been hot sellers at the craft shows.
You could probably make an entire booth of nothing but door corners.
Well we have a new design and we're going to do a test cut using this X-Tool S1.
Here we are in X-Tool creative space.
Garrett has loaded our project into the cloud, so we're going to click the cloud button,
click our project, and it's going to load it directly into creative space.
Now we've already loaded our eighth inch MDF into the laser, so the first thing we're going
to do is set the focal distance by clicking on this measure button over here.
The pin on the side of the laser head drops down and the head lowers to touch the material,
which calculates the thickness of the board.
It then resets the pin and it's ready for cutting.
Next we're going to click start marking to set the board size.
We're going to move our laser head up to the top left of the board and that is going to
set vector one, which is the top left position, and then we're going to hit the start button
on the laser.
Now we're just going to drag the laser head to the bottom right of our board, press the
start button, and that'll set the bottom right section.
Now you'll notice in creative space there's a green box around our entire project.
That is our board size.
Next we're going to set our cut and engrave settings.
We're going to start with layer one, our cut layer.
We're going to set that to 70% power, 10 millimeters per second, and then we're going to leave
lower the focus off on this because it's a relatively thin material and one pass.
Next we'll click framing and press the power button on the front of the laser to outline
our project cutting area on our board.
Since I didn't share the score settings, we did use 50% power and 150 millimeters per
second for scoring that blue layer.
Now we're ready to click process, loads it into the laser and click start.
Next we're going to cut our quarter inch pieces.
So we've loaded that board in.
We're going to move our eighth inch pieces off to the workspace area.
Go over here and grab our quarter inch pieces and move those into the workspace area.
Now this is still set for the eighth inch board, that green outline.
So the first thing we're going to do is set our focal distance for the quarter inch MDF.
Resets the pin.
Next we're going to set our vector one and vector two by moving our laser head to the
top left, pressing the button, bottom right, press the button.
Now it's going to redraw that green rectangle, even though it looks the same.
And here you can see our image is a little too big for the workspace area.
So we're going to tilt it just a little bit so everything fits on here.
Easy as pie.
And then we're going to go ahead and set our cut and score settings.
So our cut settings are 80% power and seven millimeters per second.
Now because this is a thicker material, we're going to go ahead and lower that focus so
that it'll cut through a little bit easier.
For our score settings, we're going to set this at 50% power and a hundred millimeters
per second.
And we're going to leave lower focus off.
And I'm so confident that this is going to fit on the board.
I'm just going to click process.
Now total, this only took about 23 minutes, 16 minutes for the eighth inch and seven minutes
for the quarter inch and it popped right out of there.
This thing is so space-saving and so light, mainly because it doesn't have the CO2 tube,
which means there's also no coolant.
So you don't have to mess with either of those things, which I think also makes it more durable.
To use the RA2 rotary tool and the automatic conveyor feeder, you will have to add the
riser base, which makes it a little bit taller, a little less portable.
So this thing is light enough, small enough, but powerful enough with a large enough cutting
area where I think I could take this thing to the craft show.
I think this thing can go toe to toe with the X-Tool P2, especially with that conveyor
system and the rotary attachments and the changeable heads.
This thing has all the bells and whistles, but none of the size and space needed for
all of those bells and whistles.
I think this is a, I am impressed.
I am still impressed that it got through the quarter inch MDF so quickly.
Big thanks to all of our patrons.
That is the best way to support this channel.
Join us over on Patreon where you have free files, a monthly Zoom call, and even access
to a super secret Facebook group.
Don't forget to hit that like button, subscribe, tick that bell to be notified of our new videos
each week.
And with that, we're about out of time.
Kim has to go drink some wine.
She needs some wine therapy.
Ooh, let's see if I can balance a door corner.
Oh yeah.
You still got it.
Still got it.