EC205 ELECTRONIC CIRCUITS-SMALL SIGNAL ANALYSIS OF CS AMPLIFIER - MODULE 6
Oct 5, 2023
Today we are going to discuss the most important topic in the last module,
which is the small signal analysis of MOSFET's common source.
When we study MOSFET amplifiers,
we need to study the small signal analysis of common source configuration only.
We need to find its gain, input and output impedance.
Before studying the small signal analysis of MOSFET,
we need to know the small signal model of a MOSFET.
This is the small signal model of a MOSFET.
We know that MOSFET has 3 terminals,
which are Gate, Drain and Source.
These are the 3 terminals of a MOSFET.
The small signal model of a MOSFET is Gate, Source and Terminal.
We need to put them open.
In the case of BJT, the output is a current source,
which is called Gm into Vgs,
and the output resistance of the MOSFET is Rd.
This is the small signal model of a MOSFET.
This is the small signal model of a high frequency MOSFET.
We don't need to study this,
because we don't need high frequency analysis.
Today I am going to discuss the common source configuration of a MOSFET.
I am going to discuss the common source configuration of a MOSFET.
This is not important.
We need to understand this figure.
For mid frequency and low frequency analysis,
we use this small signal model.
The Gate, Source and Terminal should be open.
On the output side, there is a current source and an output resistance.
We need to replace the MOSFET with this small signal model.
Now, let's see the small signal model of a common source configuration.
This is the small signal model of a common source configuration.
In a common source configuration,
the source is grounded.
The source terminal is common for both the input and output.
This is what we call a common source configuration.
In a common source configuration,
the capacitor CS is connected to the ground.
The input signal is applied to the gate.
The output is taken from the drain.
The output is taken from the drain terminal.
The CS is grounded.
This is what we call a common source configuration.
Now, let's see the mid frequency analysis of a MOSFET.
In a mid frequency analysis,
the V in the input is drawn in the same way.
The V in the input is drawn in the same way.
The Rg in the input is drawn in the same way.
Now, let's see the MOSFET.
What we have to do is that
we have to replace the MOSFET with the SOS signal.
We have to replace the MOSFET with the SOS signal.
We have to open the gate source terminal of the MOSFET.
current source is gm into vgs
and the output side is mosfet's internal resistance
rd
ok, so this much
from here to here
this much portion is mosfet
after drawing mosfet
the next output side is
rd
we have drawn rd
if we connect a load
and draw the output
if we connect a load and draw the output
we will get rl
ok
this much is the diagram
let me show you
in this
in the output side
connect rl
and
what we have to do
ground the cs
ground the cs terminal
so this circuit
will work
for mid frequency analysis
we have to draw the small signal model
for that
we have to draw an input
input
input is vin
vin
to draw the small signal model
vin
capacitor
rg
mosfet
gate switch
mosfet
drain
current switch
rd
rl
this is the output
if there is no resistance
look inside
rg
so we can write
input resistance is rg
now
voltage gain
load resistor
rl
rd
input voltage
vgs
output voltage
gm
vgs
rd
vgs
rd
vgs
rd
vgs
output
vin
That's it.
This is the easiest way to get the common source amplifier's small signal model.
I have asked this question many times.
I hope everyone understood.
Thank you.

