WoodWorking: Adjusting The Bevel On A Table Saw to 90 degrees and 45 degrees

TightWadDIY
899 followers
3 Video Views·Apr 26, 2018
Many table saws do not cut square. There are several ways to check for square but I find the easiest to be using a digital angle guage. I checked my table saw and realized it was off on both the 90 degree and 45 degree bevel. This can cause major issues with joinery. This video shows the step by step process for correcting my issue.
Welcome back guys it's the tightwad and today we're in my wood shop and I'm
working on my Hitachi C10 FL table saw and I wanted you to see that with my
Wixie digital angle gauge I set it on the table and then I set it on my blade
when it's raised all the way up and you can see that it goes to 89.8 degrees my
bevel is turned all the way right now so I need to adjust the way that my table
saw raises and lowers there's some settings inside the table saw that I can
adjust so that I can get to my full 90 degrees so I can get some nice clean
square cuts on my lumber. It has the same problems on my 45s it only goes to about
45.2 instead of 45 degrees even so I'm going to show you today how to make all
the adjustments on this table saw so I can get my top angle correct and my 45
degree angle correct so I can make some nice clean crisp cuts. The first step in
working with any power tool is to unplug it make sure you have no power going to
it and I'm going to remove my zero clearance insert here that I made and
then we'll remove the back of the table saw so we can access what we need to
access. I'm going to turn the bevel all the way around to 45 and start there
because it's easier to access in the insides of the saw it's easier to access
the side with the 45 degree bevel. To get to the workings for your saw you have to
remove this back plate and that's the easiest way to get in there are three
Phillips head screws on each side here and on the other side and you will be
able to pull this plate right off and then you'll be able to access everything
you need to access inside the saw. On this table saw there is a stop on each
end of the bevel right here there is a piece right here that bumps into this
that causes it to stop so this piece turns and bumps into this and cause it
to stop this is a stationary piece so inside this piece there are two holes
with an Allen screw in them that are three millimeters so you need a metric
set of Allen wrenches you need to loosen the two Allen wrenches Allen wrench
screws here and you'll be able to rotate this piece however you need to set it to
45 degrees so I'm gonna have to rotate mine down a little bit so that it'll
rotate a little bit more than it currently is. I've now adjusted a total
of three clicks on the bevel gauge and I can adjust as far as 44.9 and then
manually adjust it back to 45 degrees by turning the bevel knob so I can cut
perfect miters at 45 degrees. Now we need to do the same thing for the 90 degree
bevel mark. This side is set up similarly but it's actually in reverse so the
piece is back here that is stopping the assembly so I'm gonna need to loosen one
of the hex keys here and rotate it towards the back probably two clicks to
get the result that we want. I'm working in a very tight spot here but you can
see here I'm loosening the hex key screw and then you'll see that I pull it out
just a little bit rotate it over two posts and then slide it back into place
and then I will begin tightening it back down and this is how you adjust each
side of your bevel stop. Alright I'm going to rotate it all the way now and
you'll see that it goes to 90.2 so I can back it off manually just a little bit
to get it exactly 90 degrees and now I can make perfect 90 degree cuts on my
table saw. I hope you found this video helpful if you did give me a thumbs up
and subscribe to my channel. If you have any questions or suggestions please
leave them in the comment section below and I'll respond as soon as possible. I
hope you guys have a great day!
