DIFFERENTIAL AMPLIFIER- EC 462 Mixed Signal Circuit Design-
This video explains MOS DIFFERENTIAL AMPLIFIERS, Response of MOS differential pair to input CM variation, Response of MOS differential pair to large differential inputs, Response of MOS differential pair to small differential inputs
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
Hi all, today we are discussing about Differential Amplifiers.
You might have heard the term Differential Amplifiers.
Here, we have studied about Operational Amplifiers or Op-Amps, right?
In the paper called Analog Integrated Circuits or Linear Integrated Circuits,
we have studied about Op-Amps, Operational Amplifiers.
The most important block of an Op-Amp is the Differential Amplifier.
What is the operation of a Differential Amplifier or Op-Amp?
It amplifies the difference between the non-inverting and inverting inputs.
So, the Differential Amplifier is a functional unit of an Op-Amp.
So, today we are discussing about Differential Amplifiers.
Let us see what a Differential Amplifier is.
You have studied about Differential Amplifiers in detail when you studied Op-Amp, right?
Differential Amplifiers are two common source amplifiers which are placed face-to-face.
We have studied many performance parameters of Differential Amplifiers like
Common Mode Gain, Differential Mode Gain, CMRR, Slew Rate in Op-Amp, right?
Today, we are discussing about Differential Amplifiers as a brief introduction.
Most of the things you might have studied earlier.
First, let us see the response of most differential pair to input common mode variation.
Common mode signal is the main function of an Op-Amp.
It amplifies the common mode signals a little and amplifies the differential signals more.
Common mode signal is the ability to reject common mode signals.
Common mode rejection ratio is more in an Op-Amp.
Today, we are giving a common mode signal to a differential pair.
Common mode signal is a differential pair M1 and M2.
We are giving a common signal VCM.
VCM is given to the gate of M1.
The voltage Vcm is given to the gate of M2.
The input voltage M1 and M2 is the same.
The input voltage Vcm is given to the gate of M1 and M2.
When the same voltage Vcm is given to M1 and M2,
the two transistors will be being biased in the same way.
When the same voltage Vcm is given to M1 and M2,
the two transistors will be being biased in the same way.
In that case, the conductance of these two transistors will be the same.
In other words, we are giving the same voltage to these two transistors,
that is, we are giving a common signal.
Here, the input is a common mode variation,
we are giving a differential pair, a common mode variation input signal,
we are looking at what is happening here.
For that, we are giving the same signal to these two differential pairs,
that is, we are giving the same signal called Vcm, which is common in M1 and M2.
In that case, these two transistors, M1 and M2,
will be operating in the same region.
In that case, the Vgs voltage of M1 and M2 will be the same,
the current of M1 and M2 will be the same.
If the current is the same, then the drain current of M1 and M2,
i.e. the drain current of M1 is Id1,
and the drain current of M2 is Id2.
These two are equal.
In the case of this configuration,
the drain current and the source current will be equal.
That is, only this current is coming,
because we have studied that the gate source terminal of MOSFET is like an open circuit,
that is, the gate current is zero in the case of MOSFET.
That is, there is no gate current,
that is, the drain current will be the same as the source current.
Both will be equal.
When the drain current and the source current are equal,
we can say that the total current flowing through this MOSFET,
the current that comes here,
and the current that flows through this MOSFET,
these two currents are joined together,
the current that is going here,
till then, we know that the total current for these two currents is Is.
In that case, the current that comes through this,
and the current coming through this,
is joined together by Is.
ID1 is equal to ID2 is equal to ISS divided by 2.
When we give a common mode signal, we get a voltage here, that is Vx.
Here we get a voltage, that is Vy.
In that case, we have given the same voltage in both these transistors.
In that case, Vx and Vy will be the same.
Why?
Because we have biased both these transistors in the same way.
So, the voltage Vx and Vy will be the same.
Vx is the X point with respect to ground.
How do we get the voltage Vx?
Vx is the total voltage.
Total voltage is the voltage we have given here.
That voltage is Vdd.
If Vx is the total Vdd,
and if we go this far, we get Vx.
So, the total voltage is Vdd.
If we reduce the voltage in this resistor,
we get the voltage from the X point to the ground, that is Vx.
So, Vdd minus ID1 RD.
Isn't it? ID1 RD.
Otherwise, Vdd minus ID2 RD.
That is equal to Vdd minus ID2 RD.
Both are the same. ID2 RD.
In short, ID1 and ID2 are ISS by 2.
So, this equation is Vdd minus ISS by 2 RD.
Vdd minus ISS by 2 RD.
A zero differential input gives a zero differential output.
Here, we are giving the same input in both.
The voltage here and the voltage here are the same.
When we give the same voltage here,
there is no difference in the input.
That means a zero differential input.
There is no difference in the input.
That is called a zero differential input.
If you give a zero differential input without any difference in the input,
there will be no difference in the output either.
That means a zero differential input gives a zero differential output.
So, that is about the response of a MOS differential pair to input common mode variation.
In this common mode variation, we are giving the same voltage in both.
So, both transistors will work in the same way.
Both transistors are biased in the same way.
The current flowing through both transistors will be the same.
Thus, ID1 and ID2 will be equal.
The total current is called ISS.
Then, ID1 and ID2 will be ISS divided by 2.
Similarly, the voltage in Vx and Vy will be the same.
Both voltages will be Vdd minus RD into ISS by 2.
Is it clear?
Next, we have to compute the equilibrium overdrive voltage of M1 and M2.
We have to calculate the equilibrium overdrive voltage of M1 and M2.
For that, we assume that lambda is equal to zero.
That is, the channel length modulation is taken as zero.
If the channel length modulation is taken as zero, there will be no effect.
We can avoid the effect of the internal parameters of the transistor.
We know the equation for drain current.
Drain current ID is equal to 1 by 2 mu n Cox into W by L into Vgs minus Vth the whole square.
The equation for drain current ID is 1 by 2 mu n Cox into W by L into Vgs minus Vth the whole square.
Next, we have to find the value of ID.
The value of drain current in each transistor is ISS by 2.
Instead of ID, we can write ISS by 2 is equal to 1 by 2 mu n Cox into W by L into Vgs minus Vth the whole square.
Now, we have to find the equilibrium overdrive voltage.
Equilibrium overdrive voltage is Vgs minus Vth.
Equilibrium is equal to ISS divided by mu n Cox into W by L.
Now, we have to find the value of Vgs minus Vth the whole square.
That means the greater tail current or smaller W by L translates to large equilibrium overdrive.
Equilibrium overdrive depends on both ISS and W by L.
If ISS is more than W by L, equilibrium overdrive increases.
If W by L is more than W by L, equilibrium overdrive decreases.
If W by L is smaller than W by L and ISS is more than W by L,
we can say a greater tail current or a smaller W by L translates to larger equilibrium overdrive.
Now, we have to guarantee that M1 and M2 transistors work in saturation.
To guarantee that, Vcm minus Vth should always be greater than this value.
To guarantee M1 and M2 operate in saturation, we require that their drain voltages not fall below Vcm minus Vth.
If Vdd minus Vdd minus Rd into ISS by 2 is always greater than Vcm minus Vth,
we can say that these two transistors work in saturation region.
It can also be observed that a change in Vcm cannot alter Id1 is equal to Id2 is equal to ISS by 2,
leaving Bx and By undistributed.
Similarly, we can say that a change in Vcm cannot alter Id1 is equal to Id2 is equal to ISS by 2,
leaving Bx and By undistributed.
The circuit thus rejects input CM variation.
The main purpose of this differential pair is to improve CMRR.
CMRR is the ability to reject common mode variation signals.
Next is the response of MOS differential pair to large differential input.
In large differential, we have given common signals.
Now we are giving large differential input to this MOS differential pair.
We are giving large differential input.
That is, we are giving V1 and V2.
Let us see how this differential pair works.
If Vin is well above Vin2,
Vin1 is greater than Vin2.
Then, which transistor is ON?
M1 is ON.
M2 is OFF.
M1 is more than M2.
M1 is ON.
M2 is OFF.
M1 is ON.
M2 is OFF.
M1 carries the entire tail current.
We can write the equation as follows.
We can write Vx.
Vx is equal to Vdd minus Vdd.
Vx is the ground area.
Vx is equal to Vdd minus Vdd.
Earlier it was Iss by 2.
Here, M2 is OFF.
Then, the entire Iss current goes through M1.
We can write Vdd minus Rd into Iss.
Similarly, Vy.
Vy is the voltage at this point.
Vy is equal to Vdd.
This is the first condition.
V1 is more than V2.
Then, which transistor is ON?
M1 is ON.
M2 is OFF.
Then, which transistor is OFF?
M1 is OFF.
Then, which transistor carrying more voltage?
M2 is ON.
Then, which transistor is ON?
the circuit steers the tail current from one side to another producing differential output
in response to differential input.
In the first case, V in1 is greater than V in2 and in the second case, V in1 is less
than V in2.
In the first case, when V in1 is greater than V in2, the current flowing through M1 is more.
In the second case, when V in1 is less than V in2, the current flow through M1 is more.
In the second case, VIN1-VIN2 will be negative, because in the negative, ID2 will increase
to ISS.
In the positive case, ID1 will increase to ISS.
In the second case, VIN1-VIN2 will be negative, because in the negative, ID2 will increase
to ISS.
In the third case, ID1-VIN2 will increase to ISS.
In the fourth case, ID1-VIN2 will increase to ISS.
In the fifth case, ID1-VIN2 will increase to ISS.
In the sixth case, ID1-VIN2 will increase to ISS.
In the seventh case, ID1-VIN2 will increase to ISS.
In the eighth case, ID1-VIN2 will increase to ISS.
In the ninth case, ID1-VIN2 will increase to ISS.
In the tenth case, ID1-VIN2 will increase to ISS.
In the eleventh case, ID1-VIN2 will increase to ISS.
In the twelfth case, ID1-VIN2 will increase to ISS.
In the third case, ID1-VIN2 will increase to ISS.
In the fourth and last case, ID1-VIN2 will increase to ISS.
In the fifth case, ID1-VIN2 will increase to ISS.
Based on the erase, the result will be different.
The result is JAMES.
Here, we are giving two different signals.
The value of one is delta V.
In the other input, V in 2, we are giving minus delta V voltage.
Both are different because their phases are different.
Let us see how it works.
Here, we are giving delta V and minus delta V voltage.
The current flowing through this is ID1.
Both are giving the same value of voltage, but the phases are different.
Here, the current is split into two, ISS by 2 and ISS by 2.
ID1 is equal to ISS by 2 plus delta I.
ID2 is equal to ISS by 2 plus minus delta I.
The reason for taking minus delta I is that we are giving minus delta V voltage.
ID1 can be replaced by delta I.
Delta ID1 can be replaced by minus delta I.
Delta ID2 can be replaced by minus delta I.
This shows the difference between the two voltages.
What is delta I?
Delta I is the change in current due to input.
What is I is equal to?
I is equal to gm into Vgs.
When we study the small signal model of a MOSFET,
Vgs is the voltage.
There is a current source here.
I is equal to Vgs.
The value of this current source is gm into Vgs.
I is equal to gm into Vgs.
Delta I is equal to gm into Vgs.
The gate voltage here is delta V.
Delta ID1 is equal to gm into delta V.
Delta ID2 is equal to minus gm into delta V.
Delta Vx is the output voltage.
If we take half of this figure,
this is a common switch configuration.
Similarly, if we take this much,
this is also a common switch configuration.
We learned the equation for the gain of a common switch configuration.
Gain is equal to minus gm into Rd.
Or we can write Vout by Vi is equal to minus gm into Rd.
Or we can write Vout is equal to minus gm into Rd into Vi.
We can write minus gm into Rd into Vi.
We apply the same thing here.
Delta Vx is the output voltage here.
Delta Vx is equal to gm into minus gm into Rd into Vi.
Minus gm into Rd is equal to minus gm into Rd into Vi.
Minus gm into Rd into Vi is equal to delta V.
Vx is equal to minus gm into Rd into delta V.
Similarly, what is delta Vy?
Delta Vy is the output voltage here.
The output voltage here is also a common switch configuration.
Minus gm into Rd into delta V.
The input voltage here is minus delta V.
So, we write minus delta V here.
So, we get gm, Rd and delta V.
So, what is delta Vx minus delta Vy?
Delta Vx is equal to minus gm into Rd into delta V minus minus gm into Rd into delta V.
When we add these two, we get minus 2 gm into Rd into delta V.
That is what we get here.
Now, let us look at the differential voltage gain.
In that case, the differential voltage gain is the same as the common switch gain.
Differential voltage gain is the output gain.
What is the output gain?
delta Vx minus delta Vy divided by delta V in 1 minus delta V in 2.
What do we get instead of delta Vx minus delta Vy?
We get minus 2 gm into Rd into delta V divided by V in 1.
What is V in 1?
V in 1 minus V in 2.
V in 2 minus V in 1.
V in 1 minus V in 2 or V in 2 minus V in 1.
V in 1 minus V in 2.
What is V in 1?
It is delta V minus V in 2 minus delta V.
What is this?
Minus 2 gm into Rd into delta V divided by 2 delta V.
This delta V and this delta V cancel each other.
We get minus gm into Rd.
This minus gm into Rd is the differential voltage gain.
This is the differential voltage gain in this case.
So, what did we discuss today?
It is about the differential pair.
In this differential pair, we learned how the common mode signal works.
Then, we learned how the large differential input works.
Then, we learned how the small differential input works.
This is what we discussed today.
I hope you understood everything.
See you in the next class.

