Convert Alternator to Powerful 2500W Brushless Motor Hello Mechanics. In this new video from "The Crazy Channel" we will show you step by step how to build a powerful Brushless motor with an alternator. This engine is so powerful that you can make a kart or an electric bike with it. Learn how to convert an AC generator into a brushless motor. Table of Contents: 00:00Introduction 00:18 Repair car alternator to make a Brushless Generator 00:25 Remove pulley 01:05 Disassemble alternator 02:54 Repair propeller 03:53 Paste Neodymium magnet 07:04 Epoxy resin preparation 09:30 We solder copper cables 10:19 We assemble the Brushless Generator
homemade brush motor brushless motor bldc motor convert generator to brushless motor homemade brushless motor arduino esc motor bldc motor selfconstruct
Activate the subtitles
We are going to modify this car alternator to turn it into a powerful Brushless motor
First we are going to try to disassemble the alternator pulley
But we can't do that because the pulley has a special bearing
So we are going to weld a piece of iron between the pulley and the bearing
In this way we block the bearing of the pulley
Now we can disassemble the pulley We
continue disassembling the rear cover
And we remove all the screws
We remove the support of the brushes or carbons. We don't need this piece We
also remove the diode rectifier because we don't need it either
To remove it we have to cut the diodes
Here we have the three coil connections We remove
the screws from the alternator
housing We open the housing We extract the
copper winding
We also extract the shaft
We have to cut all the iron pieces of the rotor
They look like iron fangs
We have already cut the iron pieces
We put the rotor in the bench drill and smooth the iron surface that we have cut We
wrap electrical tape to leave the surface flat to be able to paste the magnets
Here we have the neodymium magnets. They are very strong
We start to stick the magnets on one side, right where the pieces of iron that we have cut were
We stick them with Instant Adhesive or Cyanoacrylate
We do the same right where we have cut each piece of iron
We have already stuck a row of magnets
Now we stick another magnet next to the magnets that we have placed
It is quite complicated because both magnets repel each other
We fix them with insulating tape until the adhesive dries
And so all the magnets. They have to be glued in pairs
When the cyanoacrylate dries we can remove the insulating tape
All the magnets that we have glued are with the South Pole facing out
Now we use another easier method to glue the magnets in pairs We glue
another six pairs of magnets
And the We stick with adhesive on the opposite side, just where the pieces of iron that we have cut were.
We have to stick these magnets with the North Pole facing out
. All the magnets are already glued. They should look like this
Now we empty a bottle of Coca Cola
We need the plastic container to be able to continue
We have to cut two pieces of the plastic bottle
We wrap the container with the pieces of plastic
And fix the pieces of plastic with insulating tape
Now we seal one end with hot silicone
We prepare the Epoxy Resin mixture We
fill the entire container that we have created with Epoxy Resin
.... And let it dry for 24 hours ...
Now we can remove the insulating tape and the pieces of plastic
We assemble the rotor again in the bench drill
and leave the surface smooth so that the electric generator does not vibrate
Here we have the finished rotor
Now we are going to weld three cables in the three connections of the coils
and in each welding of the cables we place heat shrinkable insulation
Now we place the rear bearing of the shaft
We mount the copper winding on the back cover of the casing
and now we put the rotor shaft in place
We put the front cover in its place...
And we put the screws back to join the casing
We fix an electrical connection strip to the rear cover of the electric generator with flanges...
...and we connect the three cables
And we already have a Brushless Electric Generator of 10,000W
Now we are going to test our Brushless motor.
We need a 48v 12Ah battery pack
AND a sensorless brushless controller. This is from 18v to 55v and 30 Amps
We connect the 3 green cables to the Brushless motor
Here we have the Potentiometer to regulate the speed
And we connect the red and black cables to the battery
We turn the potentiometer and the motor WORKS
It reaches a lot of speed
Let's see what speed It reaches the motor
We put this reflective sticker on the shaft
And we are going to measure the RPM of the motor with this laser speed meter
It does not work because the laser also reflects on the steel of the motor shaft.
We´ll wrap the shaft with black insulating tape and glue again the reflective sticker
Let's do the second test
Now it works
5100 RPM
You can buy this brushless controller on AliExpress
Well here we have this powerful 2500w Brushless motor
If you like this video, give it a LIKE and SHARE!!!
This will give us motivation to continue making more videos