Aboud Hijazi spent 2 years making these glue in bolts and we tested them to see if they were super good enough. They broke about double of their 25kn rating and the welds were bomber.
So I have some really cool glue and bolts that I want to tell you about
before we stick them in the rock and you can't tell what they are anymore.
Over two years ago, my friend hit me up from Jordan
and was asking me about bolts and he needed them.
And so let me have him explain that to you.
Assalamu alaikum.
This is Abood from Jordan.
Having bolts was very hard to get.
First of all, it was very expensive.
Second, getting long bolts wasn't easy.
Getting bolts in general wasn't easy because you have to ship them.
Then you have to pay tax and customs and all this.
Getting bolts is very hard, especially getting the long ones.
So I decided to make this.
What I appreciated about him trying to solve that problem
is he was trying to make the highest quality bolts he could at an affordable price.
They're welded on the backside like a Romer bolt.
I like how he has them stamped on the top.
These are called junipers.
He has 25 kilonewtons on here.
It's a 316L stainless steel and it's got grooves all the way down the shaft.
I'm going to squirt out some of my liquid rock 500
to make sure that it's properly mixed.
So this first squirt is probably not going to be a mixed amount.
That's too black for what I'm used to seeing.
Bummer to waste it.
But like, that's not going to cure.
Yeah, that's a better color.
Man, cold glue just does not come out the same as warm glue.
I'm only filling it up about three quarters of the way,
because by the time I put a bolt in there, it all comes up for the most part.
One trick I like to do is to have like q-tips or something with me
to where I like I can clean off the actual bolt.
If this is going to be like a thing
everyone's going to use and see instead of having all this excess crap on there.
It's going to get hard and sharp.
Yeah, it's hard and sharp and sandy, but like it probably wear off over time.
But like, it's just like I try to make it cosmetically look just as good
as I try to make it just as like safe.
I put this in last night and the glue is cured.
The first squeeze did not, the remainder did.
So like I know that what's in here is cured.
Soft shackles lead to a bigger soft shackle,
which lead to this span set that we keep adjusting the size.
In this case, we did kind of triple wrap in order to make it short enough
to reach this bolt or we can fully extend it to reach some other bolts over there.
This is the slower downer or the decelerator.
And this keeps some of this from flying.
Now, what's nice about soft shackles is they're not heavy.
So the only thing it's got to catch is this one shackle.
This load cell doesn't have a screen, but it has a cable coming out.
It was just going to go to a laptop,
getting us for the first time in bolt lusters, a graph and the number.
So I'm pretty excited about having this.
It's a 20,000 pound load cell.
This is a soft release.
So if you ever have, if you ever for some reason get inspired to do this,
you want to keep the hydraulic or the pulley system from flying this way
as soon as that releases.
And so this is wrapped around the tie rods on our BFHC,
our big fat hydraulic cylinder.
Over here, we have our hydraulic pump,
the kind of thing that you put on the back of like a dump truck.
And it runs off DC power,
which just gives us a lot of flexibility to do stuff in a mine.
Now, the anchor over here is pretty interesting
because it kept coming out, usually concrete screws,
the Titan HD Simpson concrete screws or bomber.
It's one of the strongest bolts we just use.
And they're so easy to remove when we're done.
And so we like to use those to hold down the hydraulic.
But in this limestone, it would keep coming out.
So instead of having them in tension, we put them in sheer
and we had to rearrange things to have a five point,
five point anchor.
To be fair, this is choss that's been blasted over and over.
So not all limestone is this bad, but not all granite is great.
So it's not just if you know you have a rock type, you can just do whatever.
There's so many variables.
But that's cool about bolt busters
is that when we test stuff, we kind of just learn how things break.
And so you can more easily identify what things might do in your context.
Let's pull something.
I'm impressed.
Forty one point five three in this well doesn't even look bothered by it.
There's a 25 kilonewton rating on it.
You can see here that epoxy doesn't like to stick to metal.
And so it kind of comes out.
And these grooves are very important to grab and keep it in the rock.
And obviously it did at forty one point five kilonewtons.
So broke the rock all around this in the direction that we were pulling.
This seems to be fractured up in here.
I think this is still going to be a solid placement for our next test.
Oh, this is a cool result.
So it looks like it was compromised at the first cut for the glue here.
The notches, the first notch. Yeah.
Interesting.
I'll be at pretty high, but yeah, above MBS.
But when I was looking at this earlier, I was like,
these look like they're like cut machined into there.
And that could be a possible failure.
So it didn't break until the rock failed.
So what happened was it was like being pulled so much more than it would
if there was rock in front of it.
The bolt is still in that hole.
Thirty two point two kilonewtons.
And like the rock kind of did its thing.
And then the bolt.
That's an interesting graph.
Damn, that.
I mean, this rock looks compromised.
Literally, this bolt's not even moved.
Forty four.
This bolt in good rock isn't even showing signs that we've pulled on it.
What broke?
Oh, shit. Where was this?
I think it was like right there.
Well, we lost a shackle pin out of the rock and I found it.
It's all the way in the back of this mine.
You were digging down there. Yeah.
Oh, that's crazy, man.
Fifty four. And this bolt is still bomber.
Fifty four point two three.
OK, we were successful.
Let me show you how I built this anchor.
So this is called cascading sliding X's.
At least that's what I call it, where you have like a sliding X
and sliding X to another sliding X, which this goes to
another sliding X, which goes to another sliding X.
And this is kind of loose.
And that's kind of the catch it in case like it broke.
I don't want it to go flying forward.
Six main bolts here is doing the most of the work.
And we laid the hydraulic sideways.
So the hoses aren't going to like fall the wrong way and pull the pump weird.
How are you guys doing ready for the next ones?
So I'm adding the brake test from this video into the bolting Bible.
But sometimes I make updates in that that aren't relevant to a recent video.
And the email updates that I send out every week are really helpful
for letting people know what I'm up to.
For example, I might be doing something special
and I go into the details of that in the email.
I'm also break testing giveaways.
Mr. Linescale just let me give away a Linescale three to someone in our email
list, and now Rocky is letting me give away to Rocky Talkies.
All you have to do to enter to win is open your emails
and we'll pick from those who did at the end of August.
And then next month we'll be giving away some more stuff.
Now let's pull these in tension.
Did it really not break the bolt?
Wow, that weld is bomber.
Well, is it ready to?
Twenty five fifty two point two six.
Same bolt, same result.
Pulled out.
These things got a great pull out game.
Some beautiful B roll for you guys to see that it's still a bolt.
Forty four point six nine.
Three for three.
They all pulled out.
Yeah, I mean, they all look the same.
They all pulled out the same.
Two point one four.
Here's an interesting backstory of this.
A boot hit me up almost two years before he was able to send me these
in order to test.
Now, manufacturers are really hard to get to work with you
if you're doing small batches of anything,
whether that's making quality ropes or quality bolts.
It's very hard to make climbing gear if you're not a giant corporation.
But he wanted to make them very good enough.
And so he spent a lot of time figuring out how to do that.
And the rest of this video is him sharing his story of what went into
all these decisions of something that looks relatively simple.
So I think his story is actually very valuable
because all you see is this in the rock.
You clip to it.
You trust your life to it.
And you don't often think much behind what went into this.
Now, I think it's important to figure out who's actively bolting
in the areas you frequent and help support them
because it costs a lot of money to do that.
And it doesn't happen by itself.
It could be a bolting fund.
It could be just a single person.
Maybe hit them up and spot them 20 bucks and chip in,
because if everybody does that, we'll have better bolts.
Oftentimes, when resources are limited, cheaper things go in,
and sometimes they're not the right things.
This ended up being a really nice bolt.
And I'm going to let him share the story of what went into that.
Manufacturers are not so excited to make them because in the end,
they don't make money with this to find the right person to make it for you
with the quality you desire, with a standard,
with something I would call professional.
Going through this, I did not have any any information how to make the hot
bend, cold bend, to weld, not to weld, to fold, not to fold, to this, not to that.
I tried MMA.
I tried MIG, TIG, stick.
In the end, TIG welding was the way to go.
You control contamination.
It's very precise and very strong.
And I went to another manufacturer.
He did hot bending.
He did this for me. It was amazing.
But it wasn't sustainable because each bolt took around four hours of work.
Two people need to work with it.
One with a torch, one to bend.
After you finish, it's black.
You have to polish a lot, a lot of work.
But the downsides as well were too much heat on stainless steel.
It might lose the anti-corrosion resistance.
Let us know, experts.
I'm not an expert.
The bigger the eye, the longer the shaft you have to do,
because it creates a lot of lever effect.
In the end, I did this juniper.
Juniper is a very famous tree in Jordan.
It's 12 centimeters, 11 and a half-ish, 10 millimeters.
Thank you, Ryan Jenks, for testing that and make it happen.
Ryan Jenks was working with me the whole journey from day one.
He knows a lot how much I work on that.
It's with double ring, full chain.
This one comes down to $10 each.
At least it's available in Jordan.
We have a lot of rock to be bolted here.
Come to Jordan.
If you really know how to bolt, you're an expert.
Come help me.
We have a lot of rock to be bolted, a lot of roots, a lot of potential.
So, yes, I can ship worldwide, but I haven't tried yet.
At least I ship in the neighboring countries.
This is made up to now to EN standards
with all specifications, with all testing methods.
So it is a quality bolt, 316L.
I do also 3-4-L with all types.
Depends on the environment of your using.
Thank you very much for watching.
Thank you, Ryan Jenks. Come to Jordan.
We have a lot of canyons, a lot of rock, a lot of track climbing as well.
Assalamu alaikum. Thank you very much.