The Wixey Digital Readout for planers is a BIG improvement over factory-supplied cut-depth indicators on machines. They are highly accurate, easy to read, and a breeze to install!
We love our DeWalt® DW735 13” (330mm) wood planer. It’s a great machine with good features, excellent serviceability, and comfortable controls.
The one improvement we felt was needed was a better and more accurate way to see the depth of cut being set. That’s because the accuracy of the reading you’ll get depends entirely on the angle and which you view the indicator. For my fellow geeks, this is called parallax error and is when the pointer of a device looks like it's at a different reading when it’s read at an angle compared to when read face-on.
Sure, I could bend down each time to assure I’m looking at the indicator dead level and face on, but a digital readout, set at an angle where I can simply glance down to get an accurate reading in the scale I desire - in inches, millimeters or decimals - is MUCH better!
Here are the basic steps for installation on the DeWalt® DW735 Planer:
Unplug your machine. Remove the red cut depth pointer and retain the screws Set the preset turret depth stop to ¾” and lower the planer head until it stops. Insert one of the provided short leveling screws into the jam nut at the base of the Wixey® unit and temporarily place it over the ruler scale on the planer. Use the leveling screw to raise the unit until the foot of the readout frame is level or slightly above the adjacent infeed planer table. The foot can not be below the table or the unit will have calibration issues. We used a straight edge to get the foot level with the table - this helped us later during calibration. Remove the paper backing from the adhesive tape and carefully place the readout frame over the machine scale, assuring that the frame is aligned with the edge of the existing scale. The scale will be covered. Securely fasten the readout frame to the planer. Do not depend only on the adhesive tape to keep the scale affixed. Use a 3.5mm drill bit (provided) to drill holes (using the holes in the readout frame) to insert and thread the provided 4mm screws. Insert and tighten the screws, but don’t overtighten. To move the gauge up and down as the planer is adjusted for cutting depth, you’ll now install the mounting bracket, using the holes used for the original pointer. Use the double washer and the original screws, and loosely affix the bracket to the planer. Do an initial adjustment of the readout unit. First, loosely attach the readout unit lever to the mounting bracket you just installed. Then install the connecting lever bracket to the side of the readout unit and then raise the top of the readout unit at the depth of cut we set earlier - ¾”. Tighten the screw on the side of the readout unit. Fully tighten all the connections on the lever and mounting bracket. Assure that the scale moves freely under the force of the spring. If the scale is bound, loosen, adjust, and retighten the bracket and lever link until the scale moves freely. Install 2 - AAA batteries in the readout unit and press “ON/OFF.” Power up your planer and run a flat board through set to any thickness - but be sure that material is removed from the entire top surface of the board. When done, DO NOT CHANGE THE CUTTER HEAD HEIGHT. Lift the scale and place the planed board between the rounded end of the scale and the foot of the frame. Now press the “HOLD TO CAL” button for 3-5 seconds and to set the scale to 0.000. Now remove the board and let the scale slide back down until it is against the frame foot. Now, you will measure the board with the Wixey® unit as well as an accurate ruler or caliper to assure absolute calibration. Now press the “AB/INC” button to put the readout into “INC” mode and to set the display to 0.00. Now measure the thickness of the board you planed by lifting the scale and placing the board between the foot of the frame and the round end of the scale. The display will show the thickness of the board. Confirm that reading is correct by measuring the thickness of the board with a caliper or hook-end ruler. In the unlikely event the two measurements are not the same, visit Wixey’s frequently asked questions area:
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We love this DeWalt DW735 13-inch planer,
but there's one area that just really bugs me,
and that is the standard readout.
As clear as it is, it's problematic.
It would do much better with a digital readout
that can be viewed just standing in normal position.
Stay tuned, I'm gonna show you how to install one of these
and why you should consider
upgrading your planer with one.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We love investing in good tools
that are gonna last a long time,
and certainly this DeWalt DW735
looks like it's gonna really hold up for a long time.
We certainly like the way it runs so far,
but there's one area that's a deficit,
and it's not just this planer.
It's other types of planers and thickness sanders
and those sort of things,
and that is the cutting gauge right here.
Now, this gauge, as you can see, is very clear.
It's very visible.
It's up in the front,
but it is subject to an error that,
hey, listen, my fellow geeks,
this is the real term, parallax error,
which is what happens
when you look at a gauge indicator against a gauge
and look at it from different angles.
So if I look straight, dead level at this,
straight across, but then I come up higher
and I look down at an angle and my viewpoint is higher,
you can see the apparent reading on the gauge,
on the rule, is significantly different
than it is from different angles.
Well, the only way that you can actually get
a true reading with this kind of gauge
is to be perpendicular to the rule
so that the top, the line that goes across the top
of the indicator under the rule is 90 degrees to the rule.
Well, how do you do that?
Well, it means bending down pretty low every time to do that
and I'm not just being lazy.
I just wanna put some real accuracy into this tool
and others like it.
And therefore, we chose to go
with the Wixie RW510 digital planer readout.
Now, this is a great little tool
and it's about, at the time of the filming, about $80
and that's what it comes in, just a kit form.
This is the type two.
There was an earlier version they had out, the type one.
The two main differences were the type of battery system.
This one runs on three triple A's.
The other one ran on a disc, a single disc battery.
This has a longer battery life.
Number two, the angle, if you see the display on the top,
it tends to be a little bit more angled,
makes it easier to read when you're standing
at the operator position.
But let's go ahead and walk you through how to install this.
It's pretty simple and then at the end,
we'll go ahead and calibrate it to make sure
that we're getting exactly the thickness of stock
that's indicated in the readout here.
Let's go ahead and get going.
Well, here's the tools that you're going to need
to accomplish the task.
One, you'll need a drill motor with an adjustable chuck
where you'll be drilling holes on the front
to put mounting screws in.
Number two, you need a good straight edge of some kind.
We'll point that out in a little bit why you need that.
You need three triple A batteries.
This unit does not come with them
and you wouldn't have a way to know
whether they are fresh anyway.
So you supply your own three triple A batteries.
You need a seven millimeter nut driver
and you're going to need a piece of flat wood stock
to plane and to calibrate the machine.
That's all you need.
So the first thing we're going to do
is we're going to go ahead
and make sure that the unit is unplugged.
Always make sure it's unplugged.
Did I say make sure that your unit's unplugged
before you start this?
And the second thing you're going to do
is you're going to go ahead
and take off this indicator right here
and keep the screws handy.
Be sure to keep those screws.
You're going to need them in a little bit.
Next, go ahead and set the turret to three quarter inches
and you'll need to make sure
that the height of the head of the cutter
is above three quarter before you set it to three quarter.
Now, go ahead and lower the planer
down to three quarters inches.
Once it hits a stop, don't force it any further.
All right, let's go to the next step.
Let's go ahead and get this unpackaged.
There's an adjustment nut at the bottom
or a welded on nut here
that what you're going to do
is take one of the provided jam nuts.
And in this case, we're just going to use the short one.
We'll give that a try to begin with.
Insert several turns.
You're not actually going to use this as an adjustment
but it gives you a place to rest the bracket on.
The next step is to simply take the whole unit
and place it over the existing scale.
Now, what we're looking to do here,
you'll see down at the bottom,
the nut that we, or the screw we put in it,
we ended up using the medium size one.
And what we're doing here is you need to get a block of wood
or something below here.
And the idea is to rest this on top of it
but use a straight edge, bring this over
and raise it until that foot is in line
with the adjacent planer bed table.
So let's go ahead and take a shot at that.
Make sure before you go on to the next step
that this is absolutely level with the adjacent side
or a little bit higher.
This piece is a little bit higher.
Make sure it is not lower than the table
or you'll end up with calibration problems later on.
All right, now let's go to the next step.
After you move this and you've got your setting
where it needs to be, carefully pull this away from,
remove the paper backing off the adhesive tabs
and then carefully place this back in position,
making sure to maintain the right position above the table.
Press it in place.
Use the frame back to press it in place,
not the front gauge.
There you go.
Now we can remove that.
It's now in place, but do not rely only on the tape
to hold it in place.
We now need to mount it in with screws.
All right, the next step is you need to get this front scale
and the indicator head off of it, the display off of here.
And how we do that is in the back here,
you can see this whole item slides up and down
as kept taunt by this spring.
So what you need to do is pull that spring off.
It's really easy to get around there.
And when you do that, now this rides free.
You can pull this up,
pull it out of the indicator display head,
and then you have these two pieces.
Let's set them aside for this next step.
Go ahead and then chuck up
the provided 3.5 millimeter drill bit.
And now you have two holes that are already
in the base plate of this.
So let's go ahead and just drill straight in.
Use your seven millimeter nut driver
to go ahead and drive these in.
Very nice.
That is very much a fix there.
All right, now we'll go ahead and reinstall this back in.
Push the spring back over here.
Lower this partially in.
Put the display head back on
and slide it down until it goes to the front groove
and it rides freely.
All right, go ahead and grab the spring from the back here.
Pull it out.
Rotate the head just slightly and put it around there.
Now this operates as it should.
For this particular model,
the DeWalt 735, DW 735,
you're going to use this one supplied bracket
plus what they call a double washer.
And we're going to use the original screws
that was for the indicator.
And we'll go ahead and attach that back on.
Let's do that now.
Leave them loose like this so they're easily adjusted.
Our next step is to remove this screw right here,
reinsert it through this bracket,
lower it and connect that bracket down below.
We're going to take this M6 bolt along with this nut,
a little bit of thread lock on that
and loosely put these together.
There we go.
Okay, we're going to do our first rough calibration.
And how we're going to do that is we're going to go,
since this screw on the side is loose,
we're going to go ahead and move the top of the case
until it indicates three quarter inch,
which is what we did on the turret over in the side
when we originally set this.
Now go ahead and take the side screw and put it in tightly
and then go ahead and connect up or tighten
the rest of the linkages down here.
Then let's go ahead and finishing tightening this up
and then let's move down here
and tighten all these linkages up as well.
So tighten that really in the final position.
And then we're going to reach in here as well
and get those all tightened in as well.
Now, just a bit of warning right here at this step,
you need to make sure that this will ride up
and down cleanly.
So what I'm going to do is go ahead and adjust this
and you can see it's coming up just nicely
and it's going back down.
But if yours is bound up
or something's pulled out of alignment,
then you'll need to adjust these linkages and all this
until this rides smoothly.
All right, go ahead and remove this cover off
and let's go and install the batteries.
Hey, bonus, it only takes two batteries,
not the three that I stated earlier.
Let's go ahead and power this baby up.
Automatically the top came on
and we're now ready to calibrate.
I've set the height here to run about one and a half
slightly under it.
We're going to run this two by four through it
for our next calibration step.
All right, we're now ready to calibrate
and we're going to do that in two steps.
So first of all, I've hooked up the planer
to a vacuum system.
So it's running right now.
We are going to go ahead and turn on this display
on the on off button.
And at this point, just disregard what's ever on here
because this has not been calibrated at all.
All right, we're going to go ahead
and run this board through there
and then use it to calibrate.
So it doesn't matter what height here
or what thickness you're going to plane this at
at this point.
Just make sure you're not taking off too much at one time.
I'm choosing to use the number two setting
for rough dimensioning.
Let's go ahead and turn on the planer.
All right, let's go ahead and run it.
Take that same board.
Do not change the setting on the planer.
This right here, just plane on top of the bottom foot
and let that come down to it.
Now hold this right here where it says on off calibrate.
Hold it for three to five seconds until it zeroes out.
Now you can see we're set at zero with this here.
Now hold onto the top, remove the board
and let the plunger come down.
And what you'll find is the board thickness is 1.38 inches.
And that's what this was cut at.
So now at this point, we can raise and lower it
to whatever we want.
So let's go ahead and take it up.
Let's say to one and a half inches.
And there you can see right now on the display,
1.5 inches or one half inch.
So if I run a board through that, that's going to be set.
This is a great improvement.
There's no parallax error.
And you can simply look at this display
and move it up and down.
You can also visit wixi.com and check out their FAQ pages
for all of the different planers and devices
that this unit will work on.
And then you can also see any troubleshooting guides,
FAQs, and if there are an advanced functionality
you want to use, such as using this right here,
like we just did to measure the thickness
of an existing board, you can do that.
All that is available right there at wixi.com.
One other resource that you want to be aware of
is this little simple installation guide
that shows different common planers
and common approaches to putting this together.
This really helped in the installation of this with us.
And you can simply go to the link that's shown below
in the description to get that downloaded.
And it'll really help ease this.
Even though we showed you how to do it,
you'll now have a printed resource
that you could go through one by one.
There's another great tool in the shop,
the bandsaw, that can really benefit
with aftermarket upgrades like we just did for this planer.
Check out this video where we tell you
about six great upgrades you can put in your bandsaw
that are not that expensive, but really jump up
the functionality and the accuracy of the bandsaw.
And while you're at it, check out this other video
that we made for you that YouTube thinks is just right.
Until the next time, this is Dirk Farmer Jay
from DirkFarmerJay.com.