I love my 16” (41 cm) bandsaw. It’s older but keeps on working well. The more I use it, the more it unlocks its secrets. As good as the tool is straight from the manufacturer, there are 6 things I’ve done to enhance its performance or to make it easier or more accurate to use.
Better Drive Belt. I got rid of the standard v-belt that came with the machine and replaced it with a link belt. It’s stronger, quieter, and offers as much or more traction on the pulleys as the standard belt does. Get them from:
Stronger Wheel Tension Spring. When you adjust the tension of the blade, the wheel or crank isn’t directly attached to the top wheel hub shaft. Instead, it compresses a heavy-duty spring that then lifts the top wheel, increasing the distance between the top and bottom blade wheels to create tension on the blade. The spring has a bit of give to allow the blade to run smoother. The stock spring on many machines is “wimpy” and won’t allow you to get the amount of tension you need on the blade. This is an easy fix with the affordable stronger springs on the market. Here are a few:
Saw Tension Crank. My saw is a 16” model, and because of that, fast release and set tension lever handles are not available for it. The tension handle was on top of the saw above the top wheel. It was difficult to reach and was at an angle that actually hurt my wrist. Frankly, there was too much temptation to leave the blade tensioned between uses. That’s not good for the saw or the blade.
I installed a Big Horn Tension Crank - what a difference! While not as speedy or convenient as a swing lever would be, this is a MASSIVE improvement over what came stock with the machine. The thread on the shaft of the crank fit into the wheel lift block perfectly and now I faithfully release the tension on the machine at day’s end and set it to go back to work the next time around. To learn more, visit:
To see the basic steps to modify and install the Big Horn Tension Crank, watch our episode:
COMING SOON!
If you have a 14” model and it doesn’t have a fast set and release handle for blade tension, you should get one. You’ll get to work faster with the correct blade tension, but with tension off when the saw is not in use.
Here’s an example of one of these 14” Bandsaw Tension and Release Levers:
Olson® Cool Block Blade Guides. My saw came equipped with round rod guides of hardened steel that pressed on both sides of the blade. It works, but not as well as Cool Block Guide. As the name says, they run cooler and are semi-slippery. They come in various sizes and are very reasonably priced:
Urethane Tires. Your saw’s blade doesn’t run directly on the metal wheels inside the covers. Instead, there is a “tire”, comprised of a rubbery material, that is stretched around the wheel and smoothed in place to get as consistent thickness around the wheels as possible. Many saws, like mine, have rubber tires, which dry out and crack pretty quickly.
I upgraded to urethane tires, which will last much longer and run smoother. They take a special technique to get them installed. You can see how I installed them here:
Guide Height Markings. I got tired of estimating how high the guide bottom was above the saw table or having to have the actual piece of stock to set the guide height to allow the stock to pass under it.
Michael Fortune, an ongoing contributor to the magazine “FineWoodworking” had the perfect solution shown in a recent article. Although not mentioned, it’s there in some of the photos that accompany the article.
Using 3 of my “1-2-3” blocks, I placed various combinations under the guide and then marked a line and number for each distance off the table from 1 to 7 inches. This cost me nothing, but it sure is handy! Now I can instantly set the desired heights and estimate ½ inches as well. Cool!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We love having this bandsaw,
but we were able to add six different enhancements to it
that weren't that expensive,
that just made it even better.
Stay tuned and I'll walk you through all six.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
As I said, I love having a great bandsaw.
It gets as much use around here as the table saw does.
But as it comes from the factory,
there's some great aftermarket enhancements you can add
that don't cost that much
and really jump up the performance of the machine.
Let's go through all six.
Number one, take a look at this over here.
The power drive on this used to have just a regular V-belt.
We upgraded to this type of link belt
that you can purchase that is just interlinked,
stronger, doesn't have memory,
and boy, does it transmit the power.
You just simply take it apart,
adjust it to the length you want,
get it onto the wheels,
and that is enhancement number one.
This cost about $30 to $35.
All right, the second one here is this crank handle.
Now, what was up here before was this star right here
that was pretty close to the top,
very hard to reach up from the top,
hard on the wrist, and not a lot of leverage.
Replacing it with this crank here,
and this happens to be a big horn crank handle
for this adjuster,
you can go to the link down below
to find where you can purchase one of these,
but check out this link above me
for the full install of this
and the video episode we did on that.
You can see how to do that.
The third enhancement is replacement of this stock spring
with this Carter, what's called a Cobra coil.
Very inexpensive.
You can look at the link below and find out the price on it,
and you'll find that this really jumps up
how much lift pressure you can put on this when you adjust.
Every time you screw down like this,
this starts to lift up indirectly through the spring.
If the spring is wimpy and compresses easier
like this flat or this round stock was,
you couldn't get the tension here
that you needed dependably.
So that's a really inexpensive and quick enhancement.
All right, improvement number four, urethane tires.
The original tires that came with this machine
were rubber, they dried out really quickly, cracked,
and as a matter of fact,
one of them flew off once when I was adjusting this.
I was able to get these urethane tires
from Sulphur Grove Tool,
and this is the size on my particular machine,
16 by one by 1 1⁄8,
and these things are really tough,
but they also take a special mounting approach,
and Sulphur Tool, or Grove Tool,
says please don't boil these or heat them.
That weakens them.
There's a better way.
Check out this video that we did
showing how to put these on
using some common materials in your shop
safely, effectively, and after you've got them on,
you need to kind of run them around
to get these to be all level.
You can end up with a lot bunched up on one side,
thin on the other, which causes a lope or a rumble.
So there's a tip in that video as well
that shows you how to do these.
These range in different prices.
Go ahead and check out the link below,
and you can find out what the price is for your machine,
but I would say it should be anywhere
between $30 and $50 for this upgrade.
The fifth enhancement to this bandsaw
were the guides or the blocks that go in here.
These are the stock blocks, as you can hear.
They're metal, they're hardened,
and they work relatively well.
You have to adjust them so they're riding
right on both sides of the blade,
but slightly behind the teeth.
But these are metal, meaning that
they're gonna have increased friction
compared to these composite blocks.
These are Olsen cool blocks,
and they're made of a compound
that's slippery yet resilient.
And I found right away that I was able to run them up,
put in just maybe a whisk or whip between them.
Some people use a dollar bill or a piece of paper
to just get the distance there
so that they capture the blade,
yet keep it from twisting as well as letting it run true,
and reduce the amount of heat
that's generated due to friction.
This was an inexpensive upgrade,
and they come in all sorts of different sizes
for different kinds of square guides.
These are the round rod type,
but sometimes they're square.
And this was about a $25 upgrade overall,
and really improved it, so give them a shot.
And finally, number six.
Now this is actually a tip I picked up
reading through a recent edition of Fine Woodworking.
One of the ongoing contributors there,
Michael Fortinet, spelled like fortune,
but I'm pretty sure it's Fortinet,
has this on his bandsaw that he did,
has a very similar guide and model to mine.
And what he has is on this right here,
using the bottom edge of the cover as the distance here,
when you set these in different heights,
it tells you the distance between the woodworking
or the table of where you're gonna set the wood here
to the underside of the guide,
plus a little bit of more clearance.
So of course, all this we did here
is simply create a ruler, roll this up and down.
You can use a set of one, two, three, go blocks
or set up blocks to do the same sort of thing,
and then mark on here.
And what this allows you to do,
suppose you've got a piece of stock like this,
and you're going, well,
you can probably figure out what that is,
but you want to set the height,
you can do it in advance.
Or if I know that I have something that's three inches tall,
then I'm just gonna raise that to three inches like this,
clamp it down, and I'm ready to work
instead of having to trial and error.
So it's just one of those little things
that really speeds it up.
I thought that was really clever,
and I made liberal use of it.
Hey, I'll tell you what,
I'm gonna just throw one more little tip in here.
It isn't really an enhancement,
but you really should have one of these,
and that is a magnetic base lamp.
There's nothing like having proper light on the job
to see exactly where you're cutting,
especially if you're doing detail work,
or just make sure that you're not getting drift
or anything like that.
Having a light like this is just a great way to go,
and you should have one.
I mentioned earlier the installation of this Bighorn crank
and gave you a link,
but if you're still here, you didn't click on that link,
but if you want to see it,
check out this video where we go into detail
about how to install that and how it fits
and how to adjust it.
And while you're at it,
check out this other video that YouTube has chosen
from our library that they think is your perfect interest.
We think you'll like it too.
Hey, until the next time,
this is Dirt Farmer Jay from DirtFarmerJay.com,
really enjoying this bandsaw.