How to Carve a Spoon

Family Handyman
185 followers
19 Video Views·Mar 31, 2023
This is a wonderful project to tackle for your first wood carving endeavor. For more great home improvement and DIY ideas head to www.familyhandyman.com
Every product is independently selected by our editors. If you buy something through our links, we may earn an affiliate commission.
Hi, I'm Jay with Family Handyman and today we've got a special treat.
I have my friend Charlie Eiler here to teach us all about spoon carving.
He's been carving wood for longer than you've been alive.
More than just spoons, Charlie carves an amazing array of subject matter.
Here are some examples.
Okay, today we're going to be attempting to carve a spoon start to finish.
The first thing to do is lay it out.
You can have a short handled or a long handled spoon.
I usually tell people to go by the size of the block of the wood you have.
Now I've cut my pattern out and I'm going to use a pencil.
You normally don't want to use ink because it'll smudge.
I have a lot of patterns that I use over.
I do them in cardboard because it doesn't flex as much.
And there it is ready to cut.
When cutting this out, I usually like to take and get rid of some of the excess.
And you can see I cut right on my pencil line.
Now you can see the curve is tighter than what the saw let me.
So I'll double cut so the saw kerf is twice as wide.
That way the blade will shift through and I don't snap it.
Now because this is so tight in here, we're going to do what's called file cutting once we get in there.
We're going to come in.
Now file cutting is simply using the front of the blade and just shaving it off.
We're going to cut the side view out.
Now the neat thing about this pattern is that the leaf is about as wide as the bowl is.
Therefore, when I cut a side view, it sits like this on the table.
If this is thinner or wider, it sits crooked and you have to compensate for that.
Now what we're going to do is we're going to draw a line on here.
And you can be as precise as you want.
And we're going to put the curve. This is the back of the bowl here.
This is going to be where the lip's up.
And for down here, we're just going to fade it into here.
And you've got to remember on a leaf, you need a stem.
So we're going to come in just a little bit.
I'm going to take this.
Notice how I'm running my finger like that.
You can measure if you want. I just arbitrarily put a mark in.
So you can see this.
And then for the top of the leaf, we're going to put a curve in it.
Like such.
When you come down here, leave room because you've got to have that.
If you come all the way to the point here when you start carving, you'll cut that off.
So leave a bit of distance here.
Today for the project, it's going to be pretty simple.
We're going to use basically three knives. I just have a fourth one back up.
We're going to use a straight knife.
And any straight knife will do as long as it's sharp.
These two here are called hook knives.
As you can see, one is a left-handed and one is right-handed.
It doesn't mean you have to carve left and right-handed.
That just means that one you can pull this way, and the other one you can push using the same hand.
It comes in extremely handy.
So if you're purchasing a set, make sure you get both left and right.
It will help you in the long run.
Here we are. We're going to start carving.
One of the first things you want to know is how to hold and use a knife.
I hold the knife loosely, but I hold it up here, not way down in the palm like you're going to kill a bear.
Hold it up here in your fingers so you've got control.
Now when I do it, I put my hand on the project.
Notice my thumb.
And I'll use the opposing thumb to push with the knife.
Because if you don't, and you push like this, see how you jump through?
Everything is shaking.
It's for carving hot dog sticks.
For wood carving, you want to do this and push with the thumb.
The reason being, I can only go that far.
My elbows are on the table.
The reason the elbows are on the table or hanging at my side from standing up,
if you hold your elbows up in the air, you'll get tired after a while
because you're using all your strength and muscles to hold your arms up.
Now once we start, you're going to follow with the grain.
And notice how my hands are on the table.
I've got a secure project, but I'm going to push with my thumb.
But as soon as I want to stop, I just quit pushing with my thumb.
So if I'm not doing that and going one-handed, I can't stop.
I don't have control.
So push with your thumb.
This will also allow you so you can carve all day long
without getting tired and worn out.
Now the wood we're using today is basswood.
It's a nice, clean, white wood, and it carves beautifully.
So I'm just going to take it down a ways.
Now notice how I'm pivoting the knife.
I'm not just a straight stab, and I'm not slicing.
I'm kind of doing both.
And it'll make a nice, clean cut.
Now if you're going to carve towards yourself, roll the knife over.
Here again, it's up in the fingertips.
And when I carve towards me, notice how I pull my fingers in.
I'm not pulling with my whole arm, just my fingers.
I'll put my thumb down on the project, but as you can see,
notice the thumb stops at the handle.
That's how I move the knife.
I pull towards my thumb this way.
But notice the opposing thumb is to help stabilize the project in my hand.
So as I'm carving, I have complete control.
And when I come through, it doesn't jump and go anywhere,
and I won't cut myself.
You notice it's just kind of curved over this way and curved this way.
We are going to put the groove in there, and the groove is simply just that.
It's a groove right down the middle.
You're going to go to the point up top.
And in essence, you don't want a straight line.
If you carve a straight line, that's okay.
But a little curve in there helps make it look more realistic.
Now we're going to be very careful here because we've got an exposed wrist there.
We don't want to just get wild with a knife.
But you can see I'm going in a very small depth.
It's easier to make a lot of small cuts versus one big cut.
So I'll just re-enhance that a little bit.
I'm going to turn it over.
And here again, make a couple of small cuts.
The idea is that the two cuts come together, and notice how the chip just falls out.
Now there is no thing that says it has to be so deep.
Just go until you think you're comfortable with the depth that it's at.
Next, we're going to cut the flutes in there.
Lack of better terms, the scalloping.
And that's simply going to be a cut in and a cut here.
And you can see it kind of Vs together in the bottom, the same as it did here.
Those V lines will actually turn out to look like the veins of the leaf here.
And we're going to simply do the same cut as we did there.
We're going to come in.
And notice that's not a big cut.
We're not trying to take it all out in one chunk.
Now, if you keep your thumb here as a break, you won't cut into yourself.
So we'll make a couple of small cuts back and forth.
And you can see with a nice sharp knife and a good piece of wood, it cuts pretty easy.
And it looks like a nice clean cut, except for the top.
See the little bit of fuzziness in there?
We'll just take.
And that's one little tiny cut, and we'll clean that up.
See how that little piece comes out?
And that's the difference between a good cut and a bad cut.
A lot of times when people are carving and they ask me why their project does not look quite right,
it's generally where two cuts meet and they leave a bunch of junk in the bottom like that.
And what this does is when you're carving, you're picking up, in this case,
especially with the leaf, the cuts pick up the shadows.
Well, the shadows make the difference of seeing things and not seeing things.
If you have things cut clean like this, that line will look crisp in the bottom,
and that will show up really nicely.
Don't panic if you break a little piece off or one of these ends.
You can just re-trim it to round, and nobody will notice.
Now for the stem is what I normally do next.
I usually like to put a couple pencil lines on there just so I don't take too much off by accident.
We're going to put a beveled edge because straight across just doesn't look natural.
If you look at a leaf sometime where the stem meets the tree, it is usually curved.
And I'm just going to arbitrarily go in a little bit
because I don't want to take too much off in the beginning
because I can always trim off a little more later.
Notice how I'm taking little tiny shaves,
and then I'll come in like this, lay the knife flat,
and just make a cut, and they all fall out.
Because if you try and take one big chunk, you're just forcing it, and you'll cause a chip out.
Okay, now we're ready to do the sides.
I'm holding this more like a pencil because I'm not going to force it down.
I want to make real light cuts
because if my grain goes a little crooked on here, the knife is going to want to follow it.
So I'm basically just drawing like I would with a pencil,
and each time go just a hair deeper
because now you can see I followed my pencil line.
Now I'm going to turn it over,
and this is where you have to pay attention to where your knife point is.
I'm going to come in, and I'm going to shave just a little bit off.
I don't want to go too big.
And I'm going to go so far, turn around and come back and cut it out.
But you've got to imagine where the knife point is.
See, I'm going to keep it in there like such.
Once you get the first one out, then you can start going a little better
because you have more idea where you're at.
So now we're going to turn the spoon over,
and we're going to cut the backside.
Now you have to pay attention to the fact that this part is scalloped.
We don't want to carve a groove in here.
We want to carve it to match the parallel line.
So hold it up on its side and cut in.
And now when you cut and you turn the knife to follow,
don't push hard on the top because you'll break that piece out.
So take small paper-thin cuts.
And here again notice there are small shavings.
Now once I get a few small shavings,
I'll come in and make a cut and get rid of them.
And I'm not carving all the way to the center
because on the backside of the spoon,
you don't need to do that because most people won't see it.
And just work your way in and kind of clean the cuts up.
We're going to leave it overly thick
because of the fact that when the spoon is sitting down,
people set it down, they might bang the point.
So we'll leave that a little thicker than normal.
But you can see this is half done on the bottom.
So we have the leaf done on top, the stem.
We've kind of blended in.
We've done the back.
Notice in the back we only went in so far,
so it won't crack and break.
We're going to carve the inside bowl of the spoon.
I always, even though I've carved a lot of spoons,
I still put a pencil line on.
It's an arbitrary line.
And this is the no-carve zone.
The reason we carve the inside bowl of the spoon
on the top first is once we get this looking how we want it,
we bring the bottom up to it.
I'm going to take a hook tool.
What I like to do is I just like to work towards the center.
Notice I still have my pencil line.
I make a few cuts.
Now I'll come through the other side.
When this cut matches them, they all just fall out.
I just keep working around until I get a bunch of chips in there.
I'll turn it around.
I'll take the tool, and I'll cut the chips out.
Once you cut the chips out, you can see where you're at again.
Okay, I've carved it down a ways,
and I'm kind of comfortable with the depth I'm at right now.
So what I'm going to do is notice how thick this line is.
I'm going to make a new line.
Now this edge is thinner.
This is going to be what I call my finishing edge.
You can see I got rid of most of it,
which I'm fine with for right now
because we're just roughing the bowl out.
You know, people always ask, well, how far down do I take the bowl?
I say until it looks nice and you're comfortable with it.
I'm getting close to where I kind of want to be.
So now I'm just going to clean it up
and get some of the fuzziness and the chunks out of there
so I can really see where I'm at.
I'm kind of liking where I'm at,
and the best way to tell is to go like this with your fingers,
how thick you are.
I can feel I'm still pretty thick, but I'm all right.
If I don't like this, I can go deeper,
but if I like it, I'm going to bring the bottom up to it.
Now we're just going to clean up inside
because you can see it's pretty rough and rugged looking.
So we're just going to kind of clean it up a little bit.
Now I'll kind of hold this up
so everybody can kind of see what's going on.
Now notice the pieces I'm taking out are real tiny and small,
just a little fuzziness.
I'm not trying to carve it really deep,
or I'm just cleaning it up so it looks really nice.
Now what we're going to do is go to the backside,
and that is simply rounding over,
and rounding over is just like we did
on the top part of the leaf here.
We're going to round it over.
The wood grain goes like this,
so I want to carve this way, and I want to carve this way.
You can put arrows on here,
and we're just going to start in the middle here
and just work our way down.
Once I get so far, I'm going to turn and come towards me.
Now notice here again I'm stable.
I have my thumb up here as a break
so I don't come in and cut my hand off.
Okay, you can see that it's rounded but still coarse.
Now we'll go to the other side.
Same thing.
Start in the middle, carve forward, and carve back.
And here again I'm going to just work my way up
all the way up to the top of the bowl.
But remember, we don't want to cut this lip here.
We want to make this edge nice and corner here.
The reason being is if that's rounded,
you can't scoop anything up.
So we're going to take where our edges are here
and cut this corner off.
Okay, we're just about done.
I'm just getting rid of a little bit of the knife cuts here.
I'll get my fingers out of the way so you can see better.
And we are done.
And now we're ready to go and do a little bit of sanding
and cleanup work.
As you can see, we have multiple things here.
I like worn-out sandpaper of various grits,
and I like these foam sanding blocks.
One, because they have a nice edge on them.
As you can see, it's well used.
There's a medium grit, and this one is a very fine grit.
Now to get rid of some of the coarser cuts.
Of course, you can start with a coarse paper.
Put your finger on there, put it in, and just work the bowl.
Go to a finer grit just to make sure we're nice and clean.
And as you sand and clean things up,
you might notice a little nick or something.
You can take a knife and just clean it up, or sandpaper.
You want to sand with the grain.
Don't go crosswise. Go with the grain.
I'm going to go back to a finer grit and clean it up.
I do like to leave some knife cuts in there
because if you polish it perfectly smooth,
everybody thinks you did everything on a machine.
Looks pretty good. I'm kind of happy with where we're at.
And I think we're ready to spill some finish on there,
so we'll get set up for that.
You'll notice I'm just slopping it on
so it all soaks into all the little pores,
all the little knife edges and cuts.
Okay, we wiped it all off, and I'm pretty happy with it.
We'll give it two more coats, and there you go.
We have finished a spoon.
For more inspirational projects like this,
visit FamilyHandyman.com.
