How to Carve a Wooden Spoon // Woodworking

travel, technology and convenience
157 followers
2 Video Views·Apr 6, 2023
Hi, I'm Anna of All Trades, and today I'm going to talk to you a little bit about spoon carving.
Before we get started, I'd love to give a huge shout out to Squarespace
for sponsoring this channel and making making videos like this possible.
Because I know a lot of people don't have access to wet or green wood, I have prepared a few
blanks that are dry, and we'll show you how I'll carve those, but basically it's all the same thing.
I'll start with my blank, whatever it is. I'll use either an axe or the bandsaw to rough it out,
and then I'll bring it over and use the hand tools to refine the shape further.
This is a guitar maker's advice. This is my favorite tool as far as spoon carving goes,
because it will hold your work however weirdly shaped it is. This is a curved gouge, and rather
than using a hook knife, especially if the wood is not super wet, this is my favorite tool to use.
And when I'm first establishing the bowl shape, I want to cut across the grain, so I'm going to
spend a lot of time basically just getting it out here. I don't want to take too much at a time,
and I'll use my hand power rather than a mallet, and the spoon is actually at this point already
going to start telling me which directions it wants to go. If you start noticing pieces of chip
out or tear out, you're going to see, okay, well, it doesn't want to go that way. But right now,
I'm mostly roughing, so I am fine to just power through those spots that are a little bit more
tricky. This is dry wood. Carving wet wood is a whole lot more enjoyable, but not everyone has
access to it. Note how both of my hands are always behind the chisel at all times. One of the things
that I like most about the Guitar Maker's Vise is that it keeps the work very secure so that I can
never be putting my hands anywhere that they might be in danger. So now, after I've broken kind of
into the spoon bowl a little bit, I can start paying a little bit closer attention to the grain
and what it wants to do and move around the piece accordingly. So you're seeing a ton of chip out
right here. That's because basically at this point in the wood, it wants to be carved this way and
then this way and kind of meet in the middle here. The best way to tell which direction the wood
wants to be carved is that where it changes direction inside the bowl, it's going to want
to chip away. So a really good indication, both with carving spoons or hand planning or anything
else, is that when you experience tear out, it wants to be cut the other direction. So here,
where it's got a ridge of chip out, I know that at that point something's changed. So I want to
come back here and see if it's a little happier being carved this direction. However, if I were
to keep carving just that direction, at some point it's going to want to catch the opposite way
right there. So I know, all right, this one wants to be carved this way up to that ridge point from
before. So I'll just take a few passes and kind of smooth it down to a nice little depth there and
then I'll come back this way. And this is where the real finesse of spoon carving comes in because
getting to where you can actually get a nice hand-carved bowl of your spoon where there's
little or no chip out, or even better yet, where you can get to the point where you can
carve in specific designs into the bowl of your spoon, is where you really know that you've made
it as far as sharpening your tools and figuring out grain direction. Because I really personally
love a nice faceted spoon interior. I know that that's not everyone's preference. So carving out
the bowl is pretty easy until you get to this step. And this is the most difficult thing,
basically just because as you're trying to finish it up, you don't want to make any deep gouges,
you don't want to experience any tear out, and you want to come back and fix any tear out that
you did have. So here I'm just coming and I'm making really, really light cuts. And when I
get to that point, I'm going to change direction. I'm going to come back and I'm supporting the
tool on the bevel of the tool and just putting very light pressure and just seeing if I can't
come in here and clean it up. So again, along the top rim, I'm coming from this side up to that
middle point. And then I'm coming back and coming from this side up to that middle point. And then
to get rid of all the tear out in the bottom, I'm coming from the sides and then just meeting again
in the middle there and trying not to dig myself into a corner. Remember the one thing about this
part is that you're generally limited by the shape of your tool here. So I can only use this
supporting the bevel as much as the crook of this gouge goes. So the one benefit of having multiple
tools at this point is I can switch to another tool that will allow me to get into that better.
My favorite tool for this job is a scorp or a hook knife. And so because my friend is borrowing
my favorite hook knife right now, I'm just going to use my scorp. And I'm coming along this bottom
edge from the sides and seeing if I can't just get rid of all that tear out and make the inside
of the bowl really nice. Anytime you can use sheer cuts, aka moving at an angle, you'll be able to
get some nicer results there. I also want to make sure that I get rid of any high points.
So with spoon carving, it's always about using small cuts, sharp tools, and leverage. I don't want
to have to force anything anytime because if I do, then my tool could easily slip and I could
cut myself. So I'm doing a lot of holding things differently, using my opposite hand to support
and push. And if I can get rid of all this tear out here, then I will be able to leave a nice
finish in this, which is what I would prefer to do. I mean, you can use your fingers to feel most
of this stuff. Like aside from these two little pieces of tear out, this is a really nice even,
there's a high point right here. So I come back just behind it to where the edge of the knife
will catch. I'm running the bevel along it so that that acts as a registration point.
Now I'm going to use a spokeshave. I really like using this tool for wet or dry wood. And again,
you've got to pay really close attention to what the grain wants to do. With these bandsaw marks,
we want to get down past them because they're going to lie to you a little bit. A spokeshave
can be pushed or pulled. The thing that I always like to think is that I always want to start high,
I want to rotate into the cut, and then I want to rotate out of the cut. I think the natural
tendency is for people to want to use this tool like an ice cream scoop. But if you do that,
then you're going to create tear out at the end of every one of your cuts. If this were wet wood,
I might be more inclined to use a knife to do this part of the shaping process. But to be totally
honest, ever since I took up chair making, I absolutely love using the spokeshave. So I often
will gravitate towards this. If I have a vise or a shave horse handy, this is the tool that I'm
going to want to be using. So I'm going to just keep flipping this around in the vise and shape
it with the spokeshave. Remove all those bandsaw lines. Get a closer look at what's going on with
the grain. And at this point, I want to shape the back of the bowl. I'm going to shape the
transition. These little transitions are probably the toughest part of spoon carving because the
grain direction changes so many times in this little section. One really nice thing about as
you get more comfortable with your spoon blank preparation is that the carving process goes a
whole lot faster if you've got a properly prepared blank. So if I had to remove all this material
with, you know, a smaller blade like a knife or a spokeshave, obviously this would be a lot more
time and labor intensive. And so being able to spend that time with an axe or with the bandsaw
and really get close to the shape that you want, you're just going to save yourself a ton of time.
So the very last thing that we're going to do is do any cleanup that needs to be done.
And I will do all that with a hook knife and or a straight knife. And so right here we've got a
little tear out. I want to get that. I don't really love the way that line, the direction that line's
going. So I'm going to fix it here. What I'm doing with my knife right now is called a scissor cut.
It's basically I'm holding my knife sturdy up against my body and I'm actually controlling
the cut with this hand. So that allows me to actually get a significant amount of power
because the power for the cut is coming from my lats. So because this is a piece of hard maple
and because it's dry wood, I need a significant amount of power for this cut. However,
where this wet wood, this would actually be a fairly simple cut to make. Here we've got a
tiny bit of tear out here. So I'm just going to come back and feather that out. And similarly
with the knife, I'm always have my hands in a position that they can never get cut or my body
in a position that it could never get cut. Another cut that I really like to do is here where I've
got again, a lot more power. I can have my arm be straight and cut downward by controlling the work
piece. I can cut towards myself safely by tucking in my knees. And there seems to be no sign of
intelligent life anywhere. It's using my body as a support and just making it so that there's only
a certain amount of travel. Like the knife can't slip here because it only is given the travel
that I've allowed it to make with my body position. I can make some pretty refined cuts this
way. Okay. The last thing that needs to happen is any refinements on the bowl here. So now I'm
actually using this once again as my strength. I'm holding the knife in my left hand and I'm
using my right hand to push the piece and rotate it all at once. So after we're done with the knife,
at this point we can use any sandpaper or we can use little pieces of scraper or anything.
These are really easy to make. You just cut them out a piece of old bandsaw blades,
shape them on a grinder. I'm going to come back and just find out if there's any rough spots I
really couldn't clean up with the knife. And I'll clean them up really quickly with the card scraper.
And if I'm wanting to leave a nice tool finish, knife finish thing, I think we're pretty much
good. So at this point we can add some finish to the spoon. Anything food safe will work. Mineral
oil, beeswax and mineral oil. There's actually spoon finishing products you can also purchase.
But I like to put it on with my hand because obviously if it's not hand safe, it's certainly
not food safe. And I like to just see the colors of the wood take shape and deepen as the oil
touches them. I'll put on an excessive amount to start, let it soak in. The thirstiest parts are
going to be the end of the spoon, two ends where there's end grain and anywhere that there's end
grain exposed. Then swipe away the excess, burnish it in a little bit. This process also reveals
scratches and imperfections that then you can go back and fix or not if you choose. Sometimes with
a rough, you know, a tool only spoon like this, I'll leave some of that roughness in because I
think that it just adds character to the spoon. And the thing is that I'm going to stick this in
a pot of spaghetti pretty quick anyway. So, you know, spending hours and hours fussing over every
detail, not probably super great use of time. As I mentioned at the beginning, this video is
sponsored by Squarespace, an awesome, easy to use platform where you can create a stunning website
for yourself. I've been using Squarespace since I started my business in 2012. It is really easy
for someone who's not very tech savvy like me to drag and drop and create a stunning website with
all my needs. I have a commerce section so you can buy merchandise or products that I create and sell.
I have a blog, I can host photos and videos, and it's just a great resource for me. Make sure you
go to squarespace.com for a free trial. And when you're ready to launch, go to squarespace.com
slash and of all trades to save 10% on your first purchase of a website or domain.
Squarespace provides beautiful designer templates that you can just drag and drop your material
into. And Squarespace also offers incredible customer support 24-7. So, here we have it,
a spoon carved start to finish in about 20 minutes. And it took me a long time, I will say,
to get to the point where I could carve a spoon in 20 minutes. But even now,
they certainly aren't perfect. Each one is unique, even though I will often make
similar designs every time. Each piece of wood that I carve is unique and it's going to make
all kind of decisions on its own about how it's going to look because of its own grain direction
and stock selection and everything else. So, thank you so much for taking the time to watch this
video and for supporting my channel in that way. I actually made this video as the result of a lot
of requests for a video on spoon carving. So, if you have a video that you'd like to see,
make sure you leave that in the comments below. I hope you leave this video feeling challenged,
inspired, and excited to get outside and to do things with your own hands as well. Cheers.
