BLADESMITHING | How To Make A Damascus Billet | Basics

Jason Knight
2 followers
13 Video Views·Mar 22, 2023
Damascus billet with me
fire
So these is pieces of 15 and 20 in 1084
I wasn't really certain which ones were actually 15 and 20 or 1084 because they've been all jumbled up
and the truth is steel kind of all looks the same important part is they're all clean and
I didn't have any glue or adhesive or anything
So I just put them in the vise and get it as tight as possible
And then I run a bead of weld on each corner
Doesn't have to be on the outside. I usually try to do it right on the corner, and I will run one in the center also
That's a millimatic 215
Weld the handle on
Really weld it on
The forge is already hot. I don't use any flux
I want to make sure the forge is so hot the fire shooting out once it's hot enough
I just start welding
hammer I
Go back and forth between using the hammer and the press in this instant. I was trying to get more activity out of the billet
So I'll work it to about half of its thickness
And still the first heat
Let's take it as far as I can go
And speed it up of course or sped up
Because there's sound effects
Back in the fire the old idea is to stretch this out long enough to recut and restack
Edge forging is always good on a billet that is welded
Always works steel hot to don't don't work it down until it's red. Don't these dull red colors. Just keep it hot
it's easier to keep it hot and
Move it. You know if you let it get down to cool. You have to just take more time to get it back
I'm using a hydraulic press
Again, I'm just gonna squeeze it as far as I can take it. I want it. I want to stretch it out and
Make it nice and flat
Cool thing when my press that's the big blue you I have a limit switch
There's a little micro switch on each side so I can set
How much it will?
squeeze
Thickness width whatever I want to do. I can just set it
Right there. You can see the micro switch
Chop saw the bane of the shop makes a lot of dirty in there
Cutting the end off to see what it looks like
Now what I'm doing here is welding another handle on
because the length of the forge is
Maybe 15 inches or so and I don't sit there and play with the steel. I just weld another handle on
I'll work both of these pieces of steel
until they're
the same length
Ideally I want to get
five pieces out of each one
Just making it flat
I've got both pieces same length same width
Nearly the same thickness
Once they cool down
Ready for the next step. I
Have that big saw over there, but I can never seem to make it work properly. So till then I'll continue to use the abrasive chop saw
Always lock that thing down man when you don't
it will
Grab the piece away from you snatch it out of your hand tear the wheel up
Trust me. It will happen put it in lock it down
They never come out even
I have a friend of mine doesn't know how to use a chop saw. Hopefully they watch this video
I'm using the Wilmot grinder. I'm just cleaning those little burrs off. I
Am wearing a glove. Yes, it is true
had two pieces that weren't quite long enough and
That was my fault because they can't measure
so I just stretched them out to make them the same length as the other pieces of steel and
Save myself a lot of trouble. I don't want to weigh you have a lot of waste. So the idea is to
Have as little waste as possible. If I have two shorter pieces in the stack then
It's gonna end up being trouble for me later
Now I'm grinding these back as flat as I can so if you can see I'm grinding both sides and then one edge
I'm kind of cross hatching it, you know, I'm going in several directions to make sure it's flat
I'm stuck them all back in the vise tack them together welded a new handle on ready to go
Eight pieces
Now this this stack came out a little interesting I actually have over
280 layers in this thing, but because of me sticking
Several pieces of the 1080 for all together and several piece of 15 and 20
I had a bold stack so the so the pattern came out very bold
You'll see that in the next video
Again, no flux just waiting for it to get hot
Using the press
of course I speed it up and
My technique here is always move as much of that steel as fast as I can now. I'm edge forging
Forging not the edge of a blade but just the edge of the billet
this is where a lot of billets will come apart if it's not stuck, but
This technique has been working for me for
Probably eight years now. I
Intend to use flux
And I don't have any trouble
Depress
Here's the point where you start having to decide. What do you want to make out of this?
It's gonna chop the end off and have a look
See where our steel looks like
I'm getting the final
dimension on my billet here
It's not random everybody wants to say random, but it's a lot more like a thumbprint very individual to
person making it
Two people could make the same
Billets same stack same everything and they come out two different patterns has to do with how you move it around
This is just the end cut and smooshed out flat so we can look at it and see what the steel looks like
Hey y'all, thanks for watching
Go ahead and hit that like button. If you haven't subscribed go ahead and subscribe and leave a comment
I really appreciate you watching and stay tuned for what's next. What will we do with this billet?
