Wie man eine Skulptur aus Bronze gießt | SWR Handwerkskunst

SWR Handwerkskunst
8 followers
Mar 6, 2023
Pouring a bronze sculpture is dangerous.
These 1,000 degree hot sprayers just fly through a normal cotton fabric.
It's tricky in the preparation.
And that's exactly when you smash your head with a surprise egg.
And it requires an innovative mind.
We create the pressure air through sand.
How the air is sucked out is our business secret.
At the beginning of each bronze sculpture, an original model is formed by the artist.
For example, from clay.
Until a figure for eternity is created, this model has to change shape several times.
The positive becomes a negative and again a positive.
And then again a negative.
Until in the end, the finished bronze sculpture is created.
And like with a butterfly, every single change has its meaning and is inevitable.
The Kollinger Art Pouring House in Elchingen near Ulm.
Markus Kollinger is a managing director and a trained mechanical engineer.
He is not responsible for the artistic side of these figures.
What he does is pure, precise craftsmanship.
No matter what an artist thinks of for craziness,
Markus knows how to make an exact copy of it out of metal.
Today he begins with the task of turning a tone bust of the artist Marina Seiler into a bronze sculpture.
A process that will take about two weeks and requires a lot of work.
First, he checks the silicone moulding of the bust, which a Kera mould builder had made in advance.
We have a silicone mould here, which we get from a mould builder.
It consists of a thin silicone skin, which is filled onto the original tone head.
Here it shows a negative of this head.
With a plaster cast bowl, I check the structures,
whether they have been moulded correctly and whether there are any missing parts in the mould.
Only when he is sure that everything is correct, can he start his work.
We are now creating a wax model.
The aim is to have an exact copy of this tone head in wax.
The wax that we buy is actually white and colourless, like a normal candle.
We colour it with black grease, so that there is a better contrast to the silicone mould.
So that you can see the wall thickness a little better when brushing,
so that you get an even layer.
And also from the reflection of the light, white wax is worse than black,
so that you can see the contours better.
We brush the surface to reproduce the details.
If you just poured it in, you would have inclusions, air bubbles, surface errors.
That's why you always brush the first layer.
In the first layer, it is important that you do not dab and smear,
so that air bubbles are suppressed on the surface.
So that you do not overdo it when smearing and almost close it.
That's why you have to work very carefully and filigree in the first layer,
so that the surface is reproduced well.
He has also brushed the silicone print of the front of the head with wax.
Now he can put both halves back together.
Now we can pour the mould.
To do this, he takes a slightly thicker wax with a lower paraffin content.
Based on the time, I can adjust my wall thickness,
because the wax starts to stiffen from the outer edge layer
and the liquid core remains inside.
The longer it stays in, the thicker my wax model becomes.
30 seconds is our experience value for about 5 mm wall thickness,
which we want to achieve later in the cast.
I think the result is quite good.
I'm just looking for any missing spots, if we have forgotten anything,
if we can still find an air bubble.
What you can also see very well are the fine details we talked about earlier.
You can see the fine lines here nicely.
We have to rework the places like back here behind the ear,
but we'll get to the retouching in a moment.
I'm just removing the dividing seam with a knife,
where the two halves of the mould have come together,
which you can see up here,
and I'm trying to even out the surface
so that there are no structural differences between the reworked and original spots.
You have to work extremely carefully here.
If I get too much heat in, the wax model deforms,
or a hole melts into it.
This has already happened to us,
that at the very end, when you want to put the little I on top,
and just then, like with the surprise egg,
you break the head.
And that's the moment when you say goodnight.
But why do you need the wax model at all?
Why don't you do the bronze casting right away?
What is this elaborate step in between for?
The wax model is needed,
but for that you have to look at the process backwards.
If I want to make a bronze figure,
the bronze has 1,200 degrees,
which means I need a fire-resistant mould.
And there isn't much there.
You could use ceramics or plaster.
We use ceramics.
And now I need a model
where I can get it out of this ceramic mould.
Because if I were to mould the ceramic mould over my clay head,
I wouldn't be able to get the clay head out.
And for that I need a solvable model,
which, of course, dissolves at temperature,
and that is wax.
We've been using it for 5,000 years.
So, since the process exists, beeswax is used.
This is the first casting method that actually exists.
Every detail that I work on badly,
or work on well,
forms again in the metal.
This even goes as far as fingerprinting.
If I put a fingerprint on it,
I can see it in the metal.
And because I make the wax much lighter
than afterwards in the metal,
I make sure that I rework the structure
in advance so that afterwards in the metal
I can do it much easier.
Markus adds a bit of head ornament to the bust.
He has made the butterflies
just like the head,
with the help of silicone moulds
that were cast with liquid wax.
When he warms up his instrument,
the wax melts a bit again
and then serves as glue.
And now comes a step that later,
when the head is cast,
I'm building the casting system
You can imagine that
when the head is built into our ceramic mould
and the wax has melted,
everything that is now wax
remains as hollow space.
And in these hollow spaces,
the metal flows in
like in a water pipe system in a house.
One main line,
and then it is branched into the kitchen,
into the bathroom,
so the metal is directed in this form
and flows through the pipe system
into the actual cast part.
The difficulty with this object
lies in the thin butterfly wings.
They cool down very quickly
and lose a lot of temperature
over a short period of time
and stop flowing.
Then, for example,
I only have half a wing that does not run out.
And then we are talking about a cold run.
If I poured it like this,
the metal would come here,
it would get colder and colder
and the metal would get into the butterfly
fast enough to fill it completely.
So in the casting system
lies the whole know-how of the castor.
This is also what you learn
in the training in this profession.
That you choose the right cross-sections,
that you choose the right places,
that I think about how the metal flows into the form,
that the paths are not too long.
That's where the actual know-how of the castor lies.
Now another negative of the head is produced,
the ceramic form.
Our ceramic consists of
ceramic binder, zircon flour
and quartz glass flour.
The three components together
give this cream-like liquid,
which is then distributed on the wax model.
How does it look?
Let's start.
This is the last negative.
And in this form the bronze is poured afterwards.
A lot of fine-tuning is also required here.
In any case,
you must not damage the wax model.
The difficulty with this head, for example,
is that the butterflies do not break off.
They are very filigree.
That's why it's not dipped into the pot,
but into the water.
We still have air bubbles at the back of the hair.
You can still stuff a little.
In the eye, what points to you.
By blowing on it,
we repress air bubbles
and can distribute the ceramic on the surface a little more.
Simply to close empty places.
The butterfly up there.
The ceramic application, the layer,
the wax model is actually the meat,
the egg yolk is the ceramic liquid,
and the breadcrumbs are the sand.
This is how it is built up layer by layer.
One ear still.
A little from the inside.
Not too much, otherwise it will be too heavy.
It corresponds to each other.
Good, thank you.
Now we have everything.
We have a closed panade.
Then the whole thing has to dry for about 5-6 hours.
Until the moisture evaporates.
Then the ceramic peels.
Then the water is insoluble.
Then you can immerse it again,
coat it fresh and sprinkle it with sand again.
Then this layer grows like a tree cake.
Layer by layer until about 5-10 mm
of this ceramic tank is applied to the wax model.
The mold is burned for 8 hours
at a maximum of 700 ° C in the oven.
In this process, the wax is also melted,
so that the mold is empty inside
and the metal can absorb.
The wax head is now destroyed,
but it has done its job.
We have the finished, burnt ceramic here.
Everything that was wax before is now hollow.
That means we have our pipe system here,
which is not really a pipe system.
So, the funnel is on it.
The metal can be poured in.
The mold is ready to be poured.
Our protective equipment consists of
ceramic fiber coats, Kevlar fabric,
aluminum coated, special heat-reflecting,
so that the warm radiation
does not reach the body at all
and that also syringes, when they come,
stop.
These 1000 ° C hot syringes
simply fly through a normal cotton fabric.
That means you have a lot of burns on the skin.
We lower the ceramic mold
by means of compressed air in a sandbox.
We create the compressed air
on drift sand.
Then the sand is covered with a film
to seal everything.
So that only the funnel looks out.
Then we get our liquid metal out of the oven.
The work in the casting industry
is in principle very dangerous.
You have to be highly concentrated
so that you don't pour next to each other
and don't spray too much
so that you don't injure your colleagues.
So the team has to be coordinated
with a weight of 200 kg.
That means you have to get it weighted first.
That is physically quite exhausting
under this heat.
If we now pull vacuum,
we basically suck the metal into the mold
So the metal that flows into the mold
does not have to repel air.
This allows you to create
a vacuum.
How the vacuum is created,
how the air is sucked out,
that is our business secret.
After about 10 minutes,
the cast mold has cooled enough.
Now it's time to remove the bronze bust
from its ceramic shell.
The last ceramic remains are removed
and filled with metal.
These parts can now be carefully sanded.
When the head is cast,
you have actually reached a milestone.
Until then, of course,
you always have to start from scratch
when something goes wrong.
I always start with the wax model again.
Here we have our finished cast.
Everything has flowed out,
but of course we have to process
the rest of our cast system
with a milling cutter or file.
Otherwise it looks very good.
Here we have a few small air bubbles,
but we can file them away.
We can start.
My personal favorite workplace
is actually metalworking.
You work out the final product
from the raw cast.
If you work out these details
with every file,
with every step of the work,
and then notice how you get
closer to the final product with every step.
I enjoy this effort the most.
Here we see these fine details,
these scratches, these traces of modeling
of the tool, of the original model,
which are mapped over the silicone mold,
the wax model, to the cast.
Because of this detail richness,
that's why we also call it fine casting,
because these details are not lost in production,
but are mapped,
and you can see that very well here on these lines.
And then the sandblaster comes into play.
After the raw cast is processed,
the cast skin, this reddish-brown surface,
which is basically the burnt material,
oxygen skin, the connection between
copper and oxygen, copper oxide,
is then radiated
to bring the actual material,
this gold-brown bronze, to the fore,
so that you get a uniform color tone
that won't cause any problems later when patinating.
Instead, you produce the color
from the material itself.
That means you produce
colorful salts with the copper
using different chemicals.
Depending on the chemicals,
the copper then produces a brown,
a green, a blue, a red tone.
That's why copper is also used,
because copper is one of the few materials
that can be used to patinate green.
You can already see it on the big butterfly.
It's already starting to react.
This light green is already coming out.
And now we have to brush it in
until we have all the butterflies,
and then it has to react.
That looks pretty good.
These bronze works, or in general
these art objects, are actually for eternity.
It's 3,000 years old.
It just exists.
It's nice to do something like this all the time.
We give a 5,000-year guarantee for the material.
Bronze doesn't break.
You can bury it,
you can leave it outside.
If no one breaks it, it stays for eternity.
What did you like most about this craft?
Write it in the comments.
And don't forget to subscribe to the channel.
