How to Make a Cutting Board with Minimal Tools

MWA Woodworks
11 followers
30 Video Views·Feb 27, 2023
If you're new to woodworking,
you've probably been asked to make a cutting board
or three or 12, but you may have concerns
that you don't have the right tools in your shop
to get that job done.
Well, in this video, I'm gonna show you
how I made these simple cutting boards
with only a few tools, and along the way,
I'm gonna give you lots of great tips and advice
to get you started.
All right, so I'm gonna be using hardwoods
for these cutting boards,
and I've got some walnut, maple, and some cherry
that are all leftovers from other projects,
and they're all about two feet long.
I would definitely stick with hardwoods
for these kinds of projects,
and stay away from stuff like pine, fir, or cedar.
Those are all way too soft,
and they'll make your food taste like a,
yeah.
Now, one of the challenges that you might face
as a new woodworker is what to do
if you don't yet have a joiner or a planer.
Now, these tools are critical to have in your shop
because they do give you the ability
to mill your own rough sawn lumber,
but you don't have to let that stop you
because most hardwood lumber dealers
offer the chance to buy pre-surfaced lumber.
Now, what that means is they've already done
the planing for you, and in a lot of cases,
they've ripped a straight line edge
along one side of the board,
so you can take that right to your table saw
and start cutting it right away.
So, I started out by trimming off
the rough edge of each board.
This way, I have two parallel edges for reference,
and I know that each board is the same width
all the way down the length of the board.
That's important for the next step in the process.
I wanna cut some different size strips off of each board
so that I can mix and match them
to create some different color combos.
Now, I find it safer to cut these strips
on the opposite side of the blade from the fence,
and I like to use this little trick
for getting the same width strips repeatedly.
I just set one strip against the blade
to use as a reference, and then I adjust the fence
until my board matches it.
Easy peasy, and I just repeat that same process
until I get a few strips from each board.
Oh, and I probably don't need to say this out loud,
but you don't have to have a fancy big table saw
in order to make your first cutting boards.
I was doing this same thing with a portable table saw
seven or eight years ago just fine, and you can too.
The main key is to make sure that your saw
can hold a perfect 90-degree angle
since you may not have access to a joiner.
Now, normally, cutting boards are made
from lots of narrow strips all glued together,
but also, normally, I'd have my planer
or my drum sander to flatten those.
But in this case, I'm recommending
that you use the widest boards you can find
for this project, at least nine or 10 inches wide.
I don't usually do that,
but since I won't be using my planer,
my glue-ups need to be super flat,
and the fewer glue joints that I have in this,
the better chance there is of getting a flat glue-up.
Next, I cut off about the top inch or so of each board,
and this is gonna allow me to sandwich
those other strips in between.
All right, with all my strips cut,
now it's time to design these boards.
Since I'm using three different hardwoods,
I want some of each kind to be in every board.
This walnut board will get two maples and a cherry.
The maple board will get two cherries and a walnut,
and the cherry board will get two maples and a walnut.
These three colors go so well together,
and I think each of these boards looks pretty great.
But most importantly,
each board is only gonna have four glue joints.
Speaking of glue-ups,
let's go ahead and take care of that now.
I have a few tips for glue-ups here
that I'm gonna give you.
The first is to use a water-resistant glue
when making cutting boards.
There are a few different brands.
I recommend Titebond III.
That's the one that I've been using for years,
and it's always worked great for me.
Also, we want enough glue, but not too much,
because we really want visibility to those glue joints
to make sure they are nice and even.
So I'd use a glue bottle here
that can give a nice, fine bead of glue.
I personally love using condiment bottles
just for this reason.
Now, you could use a brush or roller to spread this glue,
but I'm just gonna use the spreader
that I already have on the end of my hand.
Once I get all my pieces glued up,
I began adding the clamps slowly.
I'm really trying to be as careful as I can here,
because things are gonna wanna slide around
and go up and down and all over the place,
and I don't want that.
Because I'm using minimal tools here,
I really wanna take care to make sure
that I glue this up slowly and keep an eye on those strips
to make sure that everything stays flat.
Another tip, you really don't wanna crank down
on the workpiece here.
We're dealing with three small strips,
and they're all pretty flexible as is,
so they really shouldn't need a lot of force
to close up those glue joints.
If you're getting a nice line of squeeze out
all along each joint,
then you have enough clamping pressure.
Cranking down too hard on the clamps
is not only gonna starve the joints of glue
and possibly lead to a failure down the road,
but it can also introduce tensions in the wood,
which could cause warping, and you don't want that.
One way to check your joints
is to clean off the excess glue now,
and I find that a little water helps with this.
Now you can see clearly if all your joints are tight
and in line with one another.
You also don't have a ton of glue to sand off later
once it's dried.
Now, you don't have to do this
on the other side of the board
because we're really only doing this
to check our glue joints,
but I have another trick to show you
that you can use once the glue sits around
for about 30 minutes.
If you grab yourself a paint scraper or something similar,
just run it along those glue joints,
and the glue's gonna come off pretty cleanly.
This is not nearly as messy as trying to clean it up
while it's still wet.
Okay, final glue-up tip.
One way you can help make sure that your boards are all flat
is to use clamping cauls.
I like to just use strips of plywood
with packing tape on one side
to prevent the glue from sticking.
Just add a caul to each end of the board
and clamp them down before you clamp the board together.
Now, give those boards at least eight hours in the clamps.
Typically, I like to let them dry overnight.
The next day, I pulled them out of the clamps
and scraped off any remaining glue with the scraper.
Next, I trim these boards to final width
using my crosscut sled.
I started by trimming the ends,
and then I cut each board to 10 inches in length.
Another tip here is to always reference
the same side of the board against the fence for every cut.
This'll make sure that each cut is square
to that side of the board.
If you haven't made a crosscut sled for your table saw yet,
you can also use your miter gauge to do this.
And also, I do have plans available
to make this sled that I'm using here,
so if you're wanting to give this a try,
I'll leave the links in the description to the build video
as well as the step-by-step plans.
All right, if you're ready to sand,
I recommend that you have a couple of cheap items on hand
that just make the process go better.
The first one is some Gorilla Grip shelf liner.
This is like a rubber liner thing
that you put in your cabinet shelves
so your glasses don't clink,
but in our cases, this is gonna be good and grippy.
It's gonna keep our relatively small cutting boards
from sliding around as we're sanding them.
And then the other thing I recommend is a good pencil,
and I'll show you why in just a second.
All right, now you can see here
how grippy this shelf liner is.
My first tip for sanding is to grab a pencil
and mark up your boards.
When you've sanded all the pencil marks off,
this is a good indicator that you can stop sanding
and move on to the next grit.
And for these boards, I'm gonna start sanding at 180
and then go to 120, 180, and 220 grit.
Now, if I were using my planer or my drum sander
to flatten these boards,
I could start this process at 120 grit,
but since I'm not doing that,
I'm gonna start at 80 grit to make sure
that I clean up all that excess glue
and to make sure that all my glue joints
are flush to one another.
How much sanding you do here depends entirely
on how well your glue-up went.
If your glue-ups were flat,
then you don't have to worry about sanding away
any high spots where a strip of wood went astray.
And I'm just gonna mark up my boards again
between each grit.
Now, once I have everything sanded to final grit,
I need to take care of these edges.
And for that, I'm gonna use a chamfer bit in my trim router.
Now, you could do chamfers or roundovers here,
but come on, roundovers?
That's like having brass fixtures in your house.
Ew.
You could also do this job with a hand plane
if you don't have a router.
It wouldn't take that much longer,
and really there's less chance of tear-out in the grain
that routers can sometimes give you.
The next thing I need to do here
is to prep the boards for finish,
and I start by popping the grain with water.
This causes all the little wood fibers I cut
while sanding to stand up
like the hairs on my arm when I get cold.
When that happens,
it causes the board to feel rough and fuzzy.
And I also get the first chance
to see that grain color come to life.
I just spritz them with water from a spray bottle lightly,
and it really doesn't take that much water here.
Once they dry fully,
I knock that grain back down with my 220-grit sandpaper,
and the board is instantly smooth again.
Doing this step now prevents the board
from getting that fuzzy feeling later
the first time you clean your board
with water in the kitchen.
That's a pretty nice benefit.
Okay, the grand finale here is to apply the finish.
I like using a paste made from mineral oil and beeswax.
I make my own,
and I have a video that will show you how to make it,
and I'll leave that link in the description for you.
It's really easy to make.
I think it's a fun process,
and it makes your shop smell amazing.
I rub a liberal amount of the paste on each board,
coating it on all sides.
Now, you may have seen some other videos
where people bathe their boards in a tub of mineral oil.
Please don't do that.
That's totally overkill.
Long-grain boards just don't soak up that much oil
like end-grain butcher blocks do,
but that's another video for another time.
Just trust me, what I'm doing here is all you need to do.
If you're gonna give this board
to your sweet granny for her birthday,
she's not gonna be cursing you two weeks later
because your board is still leaching oil onto her counters.
Now, come on, you wouldn't do that
to your granny, would you?
Just let the paste sit on the boards for several hours,
and the wood fibers will take in all the oil they need
and leave the wax behind to harden on the surface.
Then you can just buff them clean with a cotton rag
until they're buttery smooth.
All right, guys, that's it.
You've made your first cutting board.
These little cutting boards are awesome gifts.
They're easy to make,
and they're great to have around the kitchen
when you just need to cut up something real quick.
Now, if you guys like this video,
I would really appreciate a thumbs up below.
And also, if you have any other questions,
please leave those below in the comments.
I would love to answer those for you.
Also, make sure that you hit that icon
to subscribe to my channel,
and please hit the bell icon so that you're notified
the next time I release a new video.
Speaking of videos,
I've got a couple other ones lined up here
that I think you guys would really enjoy.
So go ahead and check those out.
And until next time, have fun in the shop.
