Making cutting boards // How-To | I Like To Make Stuff

I Like To Make Stuff
23 followers
12 Video Views·Feb 7, 2023
Hey, I'm Bob at I Like to Make Stuff. Today, I'm going to show you how to make a whole bunch of cutting boards.
A real quick before I get started, I wanted to say congratulations to Carhartt.
They are celebrating their 125th anniversary. And to celebrate, they created a special craft beer
and then they went across the country to share it with people who do stuff with their hands.
They made a really cool video about the trip and you can check it out here or the link down in the description.
And it's really just about them going around and celebrating craftsmanship and people who actually do stuff with their hands.
It's really inspiring, it's really well shot, and it'll make you want to get out in the shop and do some stuff.
So be sure to check that out. Congratulations again to Carhartt for 125 years and let's get to the project.
Recently, I got a commission to make 12 cutting boards.
And so I started by planing down some lumber that I already had, some teak and basswood.
Now basswood feels soft to the touch, but it actually has really really tight grain which makes it really good for cutting boards.
To make these easier to deal with, I set up a stop block on the miter saw and then cut the long planks down into 18 inch sections.
Each of these is going to get cut down into strips, but rather than pushing the entire board through the table saw,
it was easier to go ahead and cut them down to length.
I took each piece over the jointer to make sure I had one nice flat face.
This face will be the guide that I use when I cut them down to strips on the table saw.
When I ripped these down to strips, I set the position of the fence and cut 12 strips.
Then I moved the fence and cut 12 more, and I just kept doing that so that I had a variation in the width of the pieces of wood.
I didn't have any more basswood milled down to 1 inch, but I did have these nice big basswood timbers that were about 2 inches thick.
They had one live edge, which unfortunately I couldn't really use for this, so I cut it down into sections and then took them over to the jointer.
I also ran them through the planer to clean up both sides of the piece of wood.
It needed to be really nice and smooth for the glue up later.
These were so thick, I had to flip it over on the table saw and make two passes to cut it down into strips.
After everything was cut, I organized the pieces by size and then went through and made a kit for each one of the cutting boards.
They didn't really need to be the same, but since I had cut 12 of every piece, it just made sense.
Then I was ready for the first glue up.
When you decide on what glue to use, make sure you do your research.
There's a lot of discussion about it and differing opinions, so decide what's best for you.
Go ahead and use a little more glue than you think you need and make sure you cover the entire surface of every piece.
You want it to be thick enough to fill any little tiny gaps in between the pieces.
Tighten them down in the clamps and then add another clamp from the other side and on the ends to make sure you get everything clamped together.
I scraped off any excess glue and then I ran it through the planer.
When you do the glue up, not everything is going to sit perfectly flush.
So running it through the planer at this point makes it look really, really nice.
I decided to keep going and cut the piece that I had just made down into different size strips.
Strips are really random widths.
I made sure to set the fence and cut the pieces from both ends to get rid of any unevenness there.
And then I did the same process for glue up just like I did before.
In this glue up, I spun around every other piece so that I ended up with an alternating pattern.
I clamped it up just like I did before but this time tried to make sure that the edges were as straight as possible so that I would have less to cut off after the fact.
I often talk about how helpful it is to have a lot of clamps and this is why.
Even with all the clamps I have, I had to do glue ups in two or three different sessions.
After they were dry, I went back and scraped off the glue again just like before and then ran it through the planer.
This is the last time they'll run through the planer so you want to make sure you do enough passes to get the surface completely down flat.
If you had a drum sander, this would be a great time to use it too.
At the table saw, just square off all the edges.
I wanted to drill a consistent hole on each of the cutting boards so I made a simple little jig and marked where I wanted the center of the hole to be.
I clamped it down to the table of my drill press and that made it really easy to cut the exact same hole in each cutting board.
I used my router and a round over bit to smooth out all of the edges.
And then I sanded pretty much forever.
I wanted to make sure that every surface, every round over, everything on every board was really really smooth.
This is kind of the end of the process.
You want to get it as smooth as possible and change grits up to about 220.
For the inside of the hole, I used a sanding sponge because it fits in there and gets off any burrs.
I used wire nuts as standoffs when I was ready to finish.
They're great because they're cheap and plastic.
And for finish, I used 100% pure tung oil.
This is one of my favorite parts because the oil just really brings out the grain in the wood.
I love the way it looks.
Don't be afraid to use a lot of oil.
You really want to make sure you get every piece of it covered and you want plenty of it to be able to soak in.
Let it soak in for about 24 hours before you add a second coat.
And this is how they turned out.
I was really happy with them and more importantly, so was the client.
And there you go. Making a cutting board is really not that hard.
You can make it more complicated by making more cuts and more patterns.
And the more specific pattern you want to make, the more you're going to have to plan ahead and be really precise about your cuts.
If you're looking for a random kind of pattern like this, you can't really do it wrong.
If you wanted to make an end grain cutting board, the process is almost exactly the same.
You take smaller pieces, glue them up into a large block, and then cut it down into the shape that you want.
When you do make your cutting board, there's two things you want to keep in mind.
The wood type and the finish type.
You want to make sure that the grain in your wood is tight enough so that juices can't get into it and spoil.
That's going to make it stink. It's going to make it not last very long.
The finish has to be completely food safe.
I used tung oil, but you could also use mineral oil and beeswax or any combination of things like that.
Just make sure you do your research, get the right kind of wood, and the right kind of finish before you get started.
I hope you like this project, and if so, let me know in the comments down below.
If you have some photos of ones that you've made, you can leave them on my Facebook page or in the comments at ILikeToMakeStuff.com
I'm on all the social networks, so you can find me on whichever one you like the best.
I've got a lot more project videos up here.
I've got a new podcast with David Picciuto and Jimmy DiResta.
It's called Making It, and we talk about creativity and design and just life.
It's not specific to woodworking.
It's just about being a maker and doing stuff with your hands.
I've also got a playlist of past episodes of Brain Pick, the live Q&A show that I do.
And if you want to find out about upcoming episodes, you can do that at ILikeToMakeStuff.com.
Thanks for watching, guys. See you next time.
