How to make a knife block (that can hold your cookbook) // Woodworking | I Like To Make Stuff

I Like To Make Stuff
23 followers
59 Video Views·Feb 7, 2023
Hey, I'm Bob and I like to make stuff. Today I'm going to make a knife block that can also hold your cookbook.
The idea for this project actually came from my live stream on Twitch which happens every single
week. On the live stream, my buddy Eric told me that he and his fiancee needed a knife block and
wanted to make their own. So Eric, I hope this is helpful. All right, let me show you how I did it.
I've got several large rough sawn pieces of basswood and I thought this was a perfect project
to finally use one of them. First, I took one side over the joiner to clean it up and get one flat
face. It's amazing how much different it looks once it's cleaned up. Then I took it through the
planer, cleaning off the two wide sides. I ran the joined face along the table saw fence to clean up
the opposite edge. I didn't put the blade all the way up because this piece was so large and I had
to run it through, flip it over, and run it through again to get a full clean face. On the chop saw,
I cleaned up one end of it and the blade didn't get all the way through but it was close enough.
Then I cut down the first piece to length and then used it as a guide to mark the second piece to cut
it at the same length. The blade didn't quite get through the depth of this wood so I had to use a
flush cut saw to trim off the back corner. It actually worked perfectly and I didn't even have
to sand it. I checked both of these pieces for square and they were close but not quite right,
so I took the sides that weren't square back to the joiner and ran them over until I got everything
nice and square. I figured out how I wanted these two pieces to sit together and then I made six
marks across the full width of these two pieces. I put numbers there too so I would remember the
order later. I ran both of these pieces through the bandsaw several times cutting along those
marks that I'd made. Each segment was two inches with the ones on the sides being one inch. I lined
the pieces back up in the correct order and then drew a little mark on each one where I wanted to
route out a slot for the blades to fit. I laid the pieces down with those markings facing up and then
laid the knives in the correct order. I centered each knife roughly within the piece making sure
that the handle was all the way on the outside of the piece of wood and traced the outline of the
blade. The only part of this that you'll actually see is the opening at the top where the blade goes
in, so the inside can actually be any shape that you want. You just want to make sure that there's
enough space for the blade to be able to fit all the way in. Next I got my router out and the
thickest blade to use as a guide. I laid it on top of the router and then changed the height so that
the bit was just a little bit taller than the thickness of the blade. For each one of these
pieces I clamped it really well down to the bench and used the router to cut on the inside of the
lines that I'd drawn. Again these don't have to be very exact on the inside but you want the opening
at the top to be right on the lines. I did a test fit with each one of the blades on each one of
these pieces as I was going along making sure that the blade could slide in the hole not just lay
down on top of it. One of the blades was a little bit curved but it actually worked fine. Then I
lined all the pieces back up in the correct order and it was time to glue them up. This was a very
simple glue up I just spread a lot of glue on all the surfaces and when it came down to it I actually
put glue in the areas that had been routed out so I really didn't need to do that. Really you just
need glue on the outside edges. Once I got all these pieces lined up and squared on the top and
the bottom of both sides I put them in the clamps and added quite a few clamps to keep everything in
place while it dried. I wanted all the joints to be very tight on this. While that was drying I
started on the little shelf and this was just a scrap of teak that I had so I cut it down to the
correct width. After the block was out of the clamps I used a scraper to get rid of the extra
glue squeeze out as much as I could before I started sanding. Then I went over it with the
orbital sander using a 150 grit moving to a 220 grit and it got really nice and smooth. I wanted
to put a small bevel on one end of it and I did this by raising the blade all the way up on the
table saw and running it through. That still wasn't quite high enough so I flipped it over
on the other side of the blade to take off the extra little bit. I sanded it smooth but it really
didn't need it. This thing's a little bit top heavy but it actually does stand up so I wasn't
too worried about it. Again I set the depth of my router to the thickness of my shelf piece
and ran it across the front of the knife block. You'll notice I started in the middle of the
piece and that's because I had the edge guide on and it's just easier that way. I also should
have cut it in two shallow passes instead of one deep pass but the burning doesn't really matter
because it's going to be on the inside. I added some glue into this slot and then knocked in my
shelf piece. Now this shelf piece is 90 degrees from the front of the block but the bevel on the
block is going to make it stick up at an angle. I used a sanding block over all of the corners
and then took a tack cloth to get rid of any sawdust on the entire thing before adding finish.
And for the finish I used 100% pure tung oil. This is one of my favorite oils to use on wood.
It always makes the grain pop and the colors really come out. This stuff turned out to be
beautiful with a little bit of oil on it. Now there has been some debate in the past in my
comments about whether tung oil is food safe or not. There is some concern about whether it's
dangerous for people with nut allergies. You'll have to do your research there when you use it
but I know in our house it's perfectly fine. I used an old cut up t-shirt to apply a really
thick coat of oil over this entire thing and I even put some down into the slots right at the
top. That way you wouldn't see unfinished grain up there when you put the blades in.
And this is it. All done and it holds a book really nicely. I didn't think we needed one of
these before but now that we have it I'm really excited about it. It turned out great. I really
love the way it looks. In fact this basswood is really deceiving. It looks like it's all basically
one color but once you get some oil on it it really looks great. There are a million ways that
you could do this project. The real key is being able to route out the slots for the knife. So you
can square it up however you want. You can chop it into pieces however you want and you don't even
have to use a router to make those slots. If you had a dremel tool or even a chisel and a hammer
you could make slots that would fit perfectly to the knives. This is a project that I think just
about anybody could do no matter what tools you have and no matter what skills you have.
So if this is interesting I hope you'll take a crack at it. I'd love to know what you think about
this one. Let me know down in the comments. I've got lots of other types of projects that you might
be interested in as well so be sure to go check those out. Don't forget to subscribe. I've also
got a second channel with some kind of non-project behind the scenes stuff. You might be interested
in that as well. That's it for this one guys. Thanks for watching. I'll see you next time.
