Wie man ein Hoftor schreinert | SWR Handwerkskunst

SWR Handwerkskunst
8 followers
2 Video Views·Feb 3, 2023
Thilo Fritz is a carpenter at the Süßenberger Carpentry in Jugenheim.
The native of Rhine-Hesse works with wood every day
and most of the time something very large comes out of it.
Thilo's specialty is courtyard gates,
often up to 4 by 4 meters in size.
Such gates are still in demand in this corner of the country.
A Rhine-Hesse courtyard gate is a tradition for us.
It just fits into the picture of the place and the environment.
I've had it for years. We built five or six.
But usually two or three.
And that is the current project.
The Jochem family wants a new gate house
and has ordered a suitable courtyard gate.
Before it can be built, a measure is taken.
Are you just writing down the measure?
The locksmith will make the iron parts and fittings for the gate.
That's why it's important that he's with us today
and agrees exactly with carpenter Thilo Fritz.
You have to see how it works for me,
that you can see what the parameters are.
The wall does not hang, the floor is uneven.
Does the gate have to rise?
Can the gate rise straight?
These are all things that you have to pay attention to.
I then have to deal with the customer again.
What kind of door handle does it need?
Does it need a mailbox?
Should the gate open electrically?
Usually after the fair, when the 3D drawing is finished.
Then the customer can look at it again.
Then you can always say, you can still change that.
But these are details.
That's it.
Okay, that's it.
Step 1 in gate construction is the frame construction.
The beams for the two gate frames
are cut out of these wooden beams by the carpenter.
Marco Kaiser goes to his hand.
He works in the company as a roommate
and is just making his master.
We measure the wood moisture.
The wood should not be more than 18% wood for processing.
We have 10.9, 11%.
So that's wonderful.
Thilo first roughly tears the wood to the required lengths.
The bolts come from the trunk of a Douglasie.
We always use them for our gates because they are in the open.
The Douglasie is a bit hardy.
As a result, it is more weatherproof than on spruce and fir trees.
It is also a bit more massive.
The Douglasie is one of those woods
that are becoming more and more important
in times of climate change in the regional forestry industry.
Now we want to cut off the edge of the bowl at our deal.
We tear it off with a cord so that we get a straight direction
into the wood.
Then we take the hand saw and cut it to the width we need.
1.2 cubic meters of Douglasie,
that's about a ton of wood, lies on the bows.
From the over 5 m long trunk
, different large frame parts are created at the end.
Posts, bars, top and bottom belts.
With the different dimensions,
it is important to never lose sight of the overview.
As little cutting should occur as possible.
That is why several frame parts are cut from one bowl.
But the middle board, the heart of the tribe, leaves Thilo outside.
Because the middle is mostly torn, you can't see very well here.
I'll turn it around.
Here you can see it better.
We don't want the crack in such engines.
If the moisture pulls in, it will continue to tear over the years.
That's why we only want the outer parts, the beautiful pieces.
Because the customer also wants to have a beautiful gate.
This is what the finished gate should look like at the end.
The construction drawing helps you.
I have given all the dimensions.
I know how high my gate is, how wide my gate is,
where the connections are made, how big the door is,
how wide the boards are.
Everything is on the material list.
You don't need to calculate much.
We can start right away.
In the workshop, the craftsmen
align the pre-cut beams right-angled.
Beforehand, Thilo looks at which side is the planer.
There is a hollow side and a round side.
Legally, the hollow side has to lie down.
That means if the frame has a curve,
so that the first half and the last half lie on my machine.
If it were the other way around, it would tilt.
It's easier that way.
At some point we take the middle off and then we have a straight surface.
The angle must be exactly 90 degrees.
The smallest deviation would be drawn through all the follow-up steps
and the gate would be crooked.
The carpenter is not yet satisfied.
If the angle is correct,
the beams come into the so-called thick planer.
Here they are planed to their final width and thickness.
This happens in several work stages.
Only a few millimeters are removed each time.
The already aligned side is also planed again
so that all the waves really disappear
and the grain appears.
After planing, you can see what comes out.
The rough surface is gone.
You can already see what it should look like.
These are our frame parts.
We have to put them together for the finished gate frame.
The company values traditional construction.
Therefore, the frame construction is not doubled,
but is held together by a classic slot and pin connection.
That means that long slots come
into the vertical gate posts where Tilo is working.
Pins are then cut at the ends of the corresponding crossbar.
This way the frame parts can be inserted into each other,
a bit like a 3D puzzle.
Tilo marks on all posts where he saws the slots.
If I have torn one,
I can transfer it to the other beam.
This is a marking gauge.
It tells me where to put my hole.
The middle third is cut out with the chain mill.
But first the carpenter has to do a little pre-work.
You have to cut off the slot a bit.
It could be that the machine damages our outer edge
and then the wood will burst away until we align it again.
This is complicated
and could take several hours at the worst.
So it's better to invest a few more minutes now.
The chain mill is a fixed stem machine.
This allows Tilo to mill the slot for the frame connection
once through the entire height of the wood.
While Tilo trimms the remaining beams,
Marco does the fine work
and frees the slots from the remaining wood fibers.
Next are the bars in the row,
the counterparts to the slotted posts.
The pins come to their ends.
The carpenter saws them on the stationary mill.
And rework again.
Now I tear the pins a little smaller and cut them out.
That means I rejuvenate them here
and then cut an oblique cut with the jigsaw.
And then the wedge that holds our connection in there will come later.
First I cut this in here at the top.
When gluing, the previously mentioned wooden wedges are driven
into these slots .
But more on that later.
Now I have to work a little more with the grinding machine
so that it goes into the pin hole cleanly.
You have to repeat this process as often as the pin fits.
A traditional gate frame is very time-consuming.
Yes, until you have adjusted everything.
For such a gate, the days are over.
The next day begins with a crucial step.
The frame parts are glued.
The carpenter needs help for this.
Because this process has its tricks.
If you put too much glue on it, you'll get the parts worse.
You can't put too little glue on it, but you can't put too much on it.
And it is also not allowed to be fiddled with.
Okay, I've got it for you.
Okay, hold on to this first.
For the first time, there is a bit of hectic
in the otherwise quiet workshop.
You are tense. It has to be glued in.
It has to be pressed together.
It all has to go fast.
If it is badly glued, you have bad cards.
That's why we do the canal measurement again.
Then you can move it a little bit.
Then it is pressed together, wedged, and then nothing happens.
So that's 3.58.
57.5 centimeters.
We have to go down here a little bit.
Can you pick it up?
Let's see, it's half a centimeter.
Does it fit?
Three, wait, let's look at the other one.
Good. Wonderful. Okay.
The diagonal fits.
So that nothing can move anymore,
the craftsmen drive two wedges of oak wood into the pins.
They push the wood apart and sideways against the pin hole.
Nothing slips anymore.
Okay, that's it.
Wonderful.
About an hour later,
the carpenter gets back to work on the glue.
When the glue has dried a bit,
you can get it out of the joint better.
If it's still too wet,
just smear the stem and if it's too hard,
you can't get it off anymore.
It comes out wonderfully from time to time.
The joint has to be free, the glue has to be gone.
Two hours later, Tilo can install the strut into the frame.
So, okay.
She holds the gate in the right angle
so that the gate frame does not move
or the construction sags over time.
So, in the middle we make an overlap.
That means I have to remove half of the wood
and do the same to my strut.
Peace and precision are important in this profession.
And you need a lot of patience.
Tilo Fritz has been working as a carpenter for over 30 years,
25 of which here in the carpentry.
His craft still brings him a lot of joy.
However, it was more of a coincidence that he came to this profession.
A friend of mine learned carpentry.
We're looking for an apprentice next year.
Go with me.
I'll be there on Saturday.
The boss gave me 20 marks.
I thought, oh, there's money.
Next Saturday I'll be back.
Now we're doing the middle part.
And again the same procedure.
It is not only important that the strut sits well afterwards,
but also that it runs properly.
From the lowest point of the gate frame to the middle.
The strut still has to be adjusted to the frame.
With the circular saw, the carpenter cuts the ends accordingly.
The exciting moment.
Does it fit?
So, the corner looks good.
Only here at the overlap you can see that we're sitting on the corner.
If I sit on the corner, I have to make another cut.
Before we knock something down, I'd rather cut it again.
Okay.
The beam edges are beveled by the carpenter with the top mill
at about 45 degrees.
These phases will later come to all gate edges.
So you don't get stuck at the edges
and the rainwater is drained cleanly.
It also looks nicer.
Then a last time for today is glued.
This ensures more stability.
A lot of wood requires a lot of material.
These full thread screws are over 20 cm long.
They don't fall off at the end, because the iron is applied over them.
A few days later, both gate frames are dry
and all edges beveled.
Tilo cuts off the protruding pin parts with the circular saw.
Marco already grinds the other gate frame at the same time.
He gets his touch-up right away, but only a primer,
because the customers are still thinking about painting the gate red again.
This is just a wood glaze
that serves as the first coat of wood.
No matter what comes on it later, or not.
I wouldn't paint it.
Hiding the grain of the wood,
hiding the color of the wood,
whether it's oak or Douglasia,
I think is a shame.
Well, after we've finished the two gate frames,
the next step is to make the groove and spring boards for the outer shell.
Then we take the Douglasia raw boards that we ordered,
cut them to the length,
and then the groove and spring are milled on it,
and a phase so that it looks fine.
And then we have them too.
Groove and spring work in principle similar to slits and taps.
Each board gets a spring on one side and a groove on the other.
This way you can put the boards together.
But first the already known pre-work.
The wood is aligned right-angled
and planed to the right thickness and width.
This time several boards at once.
This is more stable and faster.
In the beginning we finished the Douglasia boards,
but at some point there were complaints
because there were too many through-fall branches.
You couldn't use much of the groove and spring boards
that were sent.
At some point we said,
okay, we have to make use of the time.
We'll do it ourselves.
It takes almost a day longer,
but Tilo can also determine the board width himself
and adjust it to the width of the gate.
The groove and spring boards from the dealer
had a specified size.
Each board gets its spring
and then the matching groove on the other side.
So, our groove and spring boards are now 100% matching.
Very nice together.
Not too tight, not too far.
Now we just have to round the phase around the board
so that the joint is emphasized a little.
Groove and spring boards have a big advantage.
When the wood pulls together
over time due to the weathering,
the spring acts as a gap filler.
No cracks appear between the boards
and the gate remains optically closed.
The phases round off this impression.
With four phases per board,
this process takes almost an hour in total.
In the meantime, the locksmith
has finished the fittings for the gate.
So, after the locksmith has brought us the iron
to hammer on the gate,
we can now mount it.
That is, I tear it up and cut it out
and then we screw it to the gate wing.
The entire underside of the gate
as well as the upper corners
are covered with galvanized flat steel.
This serves as a protection
against mechanical damage
and keeps the gate in its original shape.
Thilo uses a jigsaw.
This jigsaw cuts to length, i.e. to the body.
Hikers brought this type of saw
to the carpentry shop about 20 years ago.
Since then it has been in use here regularly.
So, now we can almost mount the iron.
Now we just have to
grind the corner away slightly.
Yes, that looks good.
So, then you can attach the iron by force
and then you can screw it in.
The screws made of stainless steel do not rust,
just like the galvanized steel.
So, now we come to the assembly of the nut spring board.
If there is such a branch in here,
then we make sure
that the branch is on the back of the gate
and preferably disappears
under a frame part.
The lower part of the gate
is peeled first.
Thilo aligns the boards at the top of the stop.
This way he can bring them to the right length.
So, the first board.
Now we attach a little
and then pre-drill
and screw it on
so that the other boards don't move.
So that we have a direction again.
The boards got their primer the day before.
If you look closely,
the gate frame from the Douglasian trunk is slightly reddish.
The nut and spring boards have a more yellowish color.
According to the carpenter, this is not a problem.
After the final polishing,
the difference is almost no longer visible.
With work division.
One saws and drills, the other screws.
The two craftsmen only need
half an hour for the lower part of the peeling.
So, now we start with the upper peeling.
It is boarded in the shape of a nut.
Then we have to bring the first nut to size
and then we can adjust it.
In addition to the nut-shaped peeling,
courtyard gates are typical in Rheinhessen,
which have incorporated a sun in the upper area
or vertical staccades.
The carpenter has often built such gates as well.
The fact that the tasks are always very different
is just one of the reasons why Tilo likes to work with wood so much.
First of all, wood is a warm,
warm material.
It's not like iron.
It's cold and a little dirty.
And with wood, well, okay,
you get a splinter in your finger,
but it's nice to work with.
You can build anything with it.
As I said, we do everything with wood.
It doesn't matter if it's a gate, a table,
or a corner bench or whatever.
And you definitely did it yourself.
So it's not a product of the rod.
Because it always has different dimensions
and has to fit somewhere else,
it's always a little more unique.
When the parts are cut to size,
they also get a phase.
And the newly cut edges
are re-primed again.
After all, everything has to be in order.
The upper shell is also visibly screwed.
Gluing is not an option here.
It would take far too long for the glue to dry.
In addition, a later repair
would then be unnecessary.
The inner shell is in place.
The carpenter builds ring by ring around the outside.
Each board is individually adjusted,
cut and screwed.
This is the only way he can be sure
that the boards fit together
and no gaps are created.
Another step that takes a lot of patience.
until the last board.
Excess material is cut off.
A rolled-out frame
is placed over these edges.
On the lower side,
Thilo also cuts a 10-degree angle.
Because in this gap
a profile bar is attached.
Okay, so the profile bar,
which separates the upper and lower shell,
we do it for the reason
that A, the hinge wood,
is covered by the lower shell.
And the upper shell
is then cut at an angle of 10 degrees
and then placed
on the profile bar
so that the water that splashes
against the hole
can then drain
over the profile bar.
The bar was built
by the carpenter
from the remains of the Douglasian tribe.
Wonderful, fits.
The frame can be attached.
Thilo cuts its corners on a gear.
The frame fits perfectly
to the groove and springboard
and protects its edges from water.
The two craftsmen
The first gate wing
is approaching the finish line.
The frame is in place.
The profile bar is still missing.
Thilo also cut the sides
on a gear here.
If you cut it straight,
it would be a straight cut
and it doesn't look nice.
We'll make a little corner
and then the profile runs
around the corner a bit
and then it just looks better.
In addition,
no moisture can penetrate the edge.
So, and at the end
of our tour,
we make such a small groove
We then lay it in the middle
of our field here
and then the gate is ready.
About a week later,
it's time.
The finished gate
is also installed
in the new gatehouse.
This is the corner field here.
Good, go on.
Helping hands are needed again,
because one gate wing
weighs almost 400 kilos.
So, and hop!
If everything fits.
Nothing can happen, right?
Looks good already.
Thilo invested
about a month's work time
in the gate.
Today it is shown
whether all the puzzle pieces
fit together.
Now we have to
put it together a bit.
Yes, but preferably with the left part.
Fine up.
Such a courtyard gate costs
between 10,000 and 15,000 euros,
depending on which wood for the gate
and which material
is used for the fittings.
Not a cheap purchase,
but one that is worth it.
After all, the courtyard gate
should last for the next 70 to 80 years.
Lift a little.
The hatch door is installed
and the gate ready for the last grinding.
The customers
asked for a suitable mailbox.
In addition, a few strips are missing
that can only be attached on site.
These are the last screws.
If Thilo has a favorite moment
when building a gate,
then it is this one.
When you have it in the workshop,
it always looks a little different
than when it is here now.
Because in the current state,
it doesn't look like it is now.
As I said,
if the customer likes it,
that's the main thing.
Then it's done for us.
And it looks great too.
Thilo is satisfied.
The customer too?
I like it very, very much.
They did a great job.
I've known Thilo for a long time.
I appreciate his work.
It really looks great.
We wanted to paint them first,
but since the gate has become so beautiful,
let's think about it again.
I think rather ...
No, it stays that way.
Are you fascinated by craftsmanship just like us?
Then subscribe to the channel now and don't miss a episode.
