Thank you Rob Smith from Slimb Soap for prepping and breaking 100 samples to be SlackSnapped to help us understand dirt and webbing a little bit more. Thank you Dan Walsh, President of SlacklineUS and owner of Concord Analytics for creating this chart for us found at https://public.tableau.com/profile/dan.walsh2310#!/vizhome/slimb_soap/barchart
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap Raw Data spreadsheet + corresponding footage associated with each break. This all couldn't happen without you!
How much does dirt, sand, and sweat damage webbing?
Well, we did over a hundred SlackSnap rig tests on this episode of How Not to Highline.
Hi, I'm Ryan Jinks, and welcome to my gear room.
Rob Smith, the guy who makes slime soap, is out of the Michigan area, and he messaged
me and asked me if I've ever done tests on dirt, sand, and sweat, and how it affects
webbing, and I haven't.
I've only peed on webbing, which you can see here.
But something that's a little bit more relevant, especially when I've been at the beach, I've
always wondered, how much damage am I causing to my precious webbing when I'm letting it
just rub through the sand and dirt?
Well, he took the initiative to find out for us, since he is Mr. Slime Soap himself.
So he purchased the webbing and cut it into pieces and prepped all the samples, and he
flew out here to California and broke them on the machine here.
He also helped with our CRG 200 meter experiment that we did to test the Enub splits.
This video you can see right here.
And we found out how much dirt affects it.
And of course, we tested with soap to see if soap helps it or not.
And then Dan Walsh, the president of Slackline US and the owner of Concord Analytics, he
analyzes data, was so kind and analyzed our 100 samples.
Didn't realize how much work it got once it got over 30 samples.
And he made us a really cool chart, which we'll show you in a little bit of our results.
Before we dive into the data, I'm going to have Rob Smith show you how he designed the
experiment.
The way that this is going to work is I'm going to put six pieces of each type of webbing
into the saltwater mixture, also a mud mixture, and then a sand mixture.
And then I'm going to clean half of them.
So we'll have three breaks, you know, saltwater, three that are dirt, three that are mud, and
then we'll have three that have been cleaned just to compare what it looks like.
So what we have for webbings here is this Mantra MK4, just a tubular webbing from REI,
like climbing spec, and then Arrow 2, also from Balance Community.
And now this next part is why I love Rob.
He went above and beyond to do something somewhat silly to test sweat and body oils on webbing
just because it was funny.
We've gotten everything squared away as far as the saltwater, the sand, and the mud.
So what I'm going to do now is basically take six pieces of each and wrap them around me
like so, and then sit in a sauna until these are thoroughly soaked in human oils and sweat.
I will try and get some footage of it, however, I don't know how easy it's going to be to
have a camera going with naked dudes in a sauna.
So wish me luck.
So Rob Smith came to California and we broke stuff for days.
This is what 100 samples looked like in real time in 30 seconds.
Each of these bars here represents the average of the three tests that were done, and you
can see here on the brand new webbing that the Arrow 2 was, on average, a little bit
stronger before we cleaned it, and after we cleaned it, it went down to this.
And same with the MK4, this is pretty much the same, and these are actually the same
for the nylon tubular webbing.
And you can see here on our mud and our saltwater that our clean sample's stronger here and
here, but not on the Arrow 2 for salt.
It is for MK4 salt, and about the same again for nylon, but we could noticeably see a difference
with sand when we were breaking the clean samples versus the dirty.
These three cleaned averages were stronger than the unclean ones.
The sand inside a webbing, here, here, and here, damages the fibers as we are tightening
only once.
This doesn't even consider cichlid loading, where it could be causing quite a bit of damage
if the sand was left in it.
And sweat is basically irrelevant.
Cleaned is a little bit lower here, a little bit lower here, and a little bit stronger
here.
I don't really think sweat does a lot of damage to webbing, and we can compare it to our brand
new webbing over here.
They're about the same, that's about the same, and this is about the same.
Here's a fun one, is our permanent line that I had set up my Arrow 2 on my permanent midline
in the trees that I've done several videos with.
You could see the uncleaned version here, just the way I took it down after I de-rigged,
is significantly lower on average around 17 kN, whereas brand new Arrow 2 was breaking
around 28, 29 kN.
So we lost almost 10 kN, leaving it up for only one year in the trees permanently.
And you can see here how cleaned versus uncleaned doesn't really make a difference because the
damage is already done.
Basically you want to get the sand out of your webbing as soon as possible, and salt
water would probably cause damage over time, and same with mud.
These were only soaked in the mud and salt and sand, and it wasn't actually in the fibers
being oscillated over and over, cyclic loading, stretching, and being used.
I think when you use the webbing with mud, salt, and sand, it would actually cause a
lot of damage, and I don't think soap is going to make that stronger.
However, if you can get it out of your webbing, it will preserve the strength more and more
as you're using it.
Now if you have hundreds or thousands of dollars invested in webbing, it's nice to keep it
clean just for visual purposes also.
And soap versus just straight up water actually binds with the dirt and can pull it out of
the fibers better.
All you have to do is put your webbing into a bucket of warm water and pour in the amount
that it recommends on here, and then swoosh it around a little bit, let it soak, let the
soap pull that dirt out, and then you just rinse it two or three times.
Now Rob designed this soap with the Natural Soap Company in Michigan to not be slimy,
ironically, which if like a normal soap could leave a residue on the line that can make
it slippery and possibly slip in webbing or leave residues you don't want.
This is a natural soap that allows friction to stay on the webbing while still cleaning
it.
So thank you Rob Smith and Slime Soap for sponsoring this video and doing all sorts
of experiments to help us get one step closer to understanding how dirt, sand, salt, and
sweat affects our webbing.
And we can do some more experiments in the future with different kinds of soaps maybe
or webbing that was in sand and then used multiple times and then broke test to see
how fast it deteriorates as we kind of use and abuse this stuff.
This isn't magic soap that makes your webbing stronger, but it can preserve it and keep
it clean.
But even perfect clean webbing doesn't always break consistently, therefore you shouldn't
highline.
Hey thanks for watching, but don't be an idiot and think now that you know how to clean webbing
with soap that you can go out and rig your first highline by yourself without going with
someone who knows what they're doing.
There are too many slackliners today to learn from to try to do this stuff on your own.
Go to slackademics.com to see this chart and find slackliners near you and learn tons of
stuff more from everyone else from the internet.
And thank you to my patrons who help support this channel.
Those people who get involved or if you want to do a one-time PayPal donation gets the
Slack Snap raw data sheet, which now we have over 500 break tests.
And then we have all the videos correlated with each of those breaks in case you want
to see in detail how we did each one.
Now if you like this video, be sure to hit the thumbs up or the like button and check
out our other videos.
And until you have a chance to wash your webbing with slime soap, make sure you follow or subscribe
and hit that bell button so you don't miss any of our future episodes.
Cheers.