DIY Projects — Wood Coasters — How To Woodworking

Blacktail Studio
97 followers
65 Video Views·Jan 8, 2023
Hey this is Cam with Blacktails Studio and this week I'm going to show you
what I do with my scraps. These were two maple burl scraps I had after making a table that
weren't really good for anything else so I turned them into these little coasters here and a lot of
people do wood coasters. I haven't seen many like this, not at all saying that I invented it,
but I'm going to show you the process here in just a couple minutes. I started over at the bandsaw
and this is my Laguna 14bx and you want to make sure the entire piece clears. I've done this
where you get the cut started and then the very peak of it doesn't quite clear and here's another
good tip is I found eight millimeters to be the perfect cut point. That makes it thick enough
after it's all sanded that you still have a coaster that's not going to break on you,
so eight millimeters is a good place to be. While I'm looking at it I have a three quarter inch
carbide resaw king blade that most people tend to put a little bit thinner blades than this on
their bandsaws and I used to as well. I find most of my cuts I make with my bandsaw are straight
or pretty straight anyway. I have another three eighths inch blade that I haven't put on in about
six months, so I really like the three quarter inch because you get to a really clean cut for
tall resaws like this. Realistically to make coasters like this you do need a bandsaw,
but I wouldn't say you need a drum sander. It does help to get them a perfectly uniform thickness,
so that's why I ran them through the drum sander there. Get everything just the right thickness,
get those saw marks out. Don't make the mistake that I've made too many times when I first made
these coasters and wait to start sanding them until you get them to the final size.
So what I'm going to do here is I'm going to sand everything to 180 grit while they're in as big a
piece as possible. That's going to save me from having to hold tiny little coasters in my hand
and sand one at a time. And if you're curious what this funny looking device is, it's a Festool vacuum
clamp. It's pretty handy, it's definitely not necessary for something like this. What I used
to use is just a rubber pad set on my workbench that I sand on that kind of keeps the vibrations
down. So I'd really just recommend using a rubber pad for this type of work, but the vacuum clamp is
obviously pretty nice. I played around with the different sizes of coasters over the years I made
and I found that four inches is a good standard coaster if you want to make kind of an XL one,
maybe for beer steins four and a half inches. But with a live edge you're obviously going to have
some fluctuation there, so I tried to get everything to about four inches wide by roughly
four inches with the live edge. And about half the coasters I did in this batch were perfectly
square and the other half were with a live edge. Here's some of the square ones and for no particular
reason I did just a chamfer bit here. It's a 45 degree bit and just made the edge a little more
interesting than rounding it over. For the ones with the live edge I just went with my regular
1 1⁄8 inch round over bit, which is kind of my default alternative to just hand sanding over
a corner. The 1⁄8 inch gives you a nice uniform rounded over look that just looks
more finished than doing it by hand. So here's a shot of the 1⁄8 inch round over. Again,
just a nice look. Here's the Porter Cable Restorer which does a nice job of taking any
bark, loose stuff, dirt off without scarring the wood itself. Moving on to the finish process,
I've used a lot of different finishes for these coasters and this time I'm going to go with an
armor seal. It's a urethane type finish and it's a wipe-on finish but it's not quite as easy as
Osmo or Odie's oil. It does take a few coats but since these had a lot of softer wood in there,
this is spalted maple and the spalted parts can be really soft. This does a nice job of
penetrating and giving a really hard durable finish that'll be nice for these coasters.
While you're watching my hyper finish here, I'll explain the process. The first coat is pretty
heavy. You can even brush it on if you wanted. I prefer to wipe it on, come back, sand it,
then apply a second coat and then if necessary, a third or fourth.
These sanding sponges work really well because they don't really scar the material. They just
take off the the dust nibs and the little imperfections in there. I go through the
whole thing, sand it with these sanding sponges. You don't have to use this exact type. Any of
the ones at Home Depot are fine. 220, 320 grit, I think this was even a 400 to 500 rated sanding
sponge. Get everything nice and flat and then apply the second coat. Oh, and after you blow
them off with some compressed air, these microfiber towels are the best thing for
getting all the last little bits of dust off of there. Then just like the first coat, add the
second coat. This coat you can go a little bit lighter on, kind of wipe off any excess and it'll
make it a little bit more uniform. You can see here, this is that spalted wood and how
it's absorbing differently. This will take a few more coats, especially one like this.
This piece was really nice, probably good after two coats. I think I put three on anyway,
but the other ones may take a few more. I'll spare you having to watch me add the third,
fourth, and fifth coats on there. As I mentioned here, the more solid pieces took three coats,
the softest took five coats like this one. I liked it with a crack, you may not be into it
with a crack. Here's all the different styles. These all came from just those two pieces of wood.
Since I'm always looking to streamline my business, I'd be curious to know which ones
of these are your favorite and maybe which ones I shouldn't bother making.
Because the cool thing with wood is everything is so different, but the frustrating thing with
wood is everything's so different. Like this kind of punky, soft, spalted maple.
This one was some crazy colors. I like that one quite a bit. There's a bookmatched of the more
solid ones. These are really pretty. And then these square ones, which aren't quite as exciting,
but still neat in their own way. I'm hoping some of you out there are watching this because you're
looking for ideas on things to use your scrap wood for. I found these have sold really well
around Christmas and Mother's Day. They don't really cost anything other than your time,
which obviously isn't free, but if you have some downtime and you're looking for something
to expand your catalog, I think these can be a nice addition. With 60 coasters made,
it'll be about 600 bucks, which isn't bad for zero cost of materials, just a little bit of time.
Okay, that's the whole video. I appreciate you tuning in. Don't forget to comment with
which ones you liked best and which ones you liked least. It'll help me with my next batch.
And if you enjoyed this video, please subscribe for more like it. Thanks a lot.
