Japanese woodworking - Cutting out a Curved Beam

Shoyan Japanese Carpenter
89 followers
9 Video Views·Dec 24, 2022
Hello, this is Shoyan, a Japanese carpenter.
Today, I'll process this curved decorated beam.
I've kept this one for 5 years after cutting off from my log.
I would like to shape this beam by chainsaw now.
First, decide the shape of the beam.
Mark on the timber a little long.
This material is pine.
It's a Japanese red pine.
This material is not very long.
It's 3 meters long.
I'll make a beam using the portion called akami.
I'd like to make this beam look like a log.
Actually, it's a straight material.
So, I draw the curved line based on my imagination.
Then, cut out the shape roughly by chainsaw.
If the portion to be removed is too big and heavy,
make a small cut at the bottom side first
before cutting full height of it.
If you cut it only from the top side
without that small cut at bottom side,
this material may tear and cause damage in the beam.
Cut it along the marking.
This time, it's a curved line.
So, it cannot be cut by circular saw.
It's dangerous due to kickback.
Then, it's better to cut by chainsaw.
It's still dangerous a little bit,
but I think it makes sense.
Rough cutting is completed.
The next step is to adjust the shape by electric plane.
This electric plane is only for logs.
Its surface is warped to fit curved timbers.
It's called sawedai,
which is a special electric plane that is warped.
After planing it by warped electric plane,
finish the shape by straight electric plane.
The four corners of the section of the beam
should be made vertical.
Otherwise, the finishing will look strange
after fixing it at the position in building.
It's difficult to finish the curved line by straight plane
if you are not accustomed.
Next, finish the surface as well.
Keep the electric plane 40 to 50 degrees against the surface.
Plane the top side as well.
Top side is the portion that sticks out,
so it's easy to finish it by electric plane.
Plane the side surface as well.
This electric plane is a little heavy,
but it can plane 30 cm wide,
which is the widest in this type of electric planes.
It's like a handy type of automatic planes.
Now, the shape is fine.
Then, start marking.
First, draw a horizontal marking,
thinking about how to fit this beam in the position.
Draw a horizontal marking.
This horizontal marking becomes the reference line.
So next, draw the dimensions measuring from that line.
Basically, marking should be drawn with Japanese ink,
which is called Sumi.
But this time, marking is drawn after planing.
So, I draw the dimensions by ballpoint pen.
It's not the right way, actually.
Next, cut out the unnecessary edge portion.
This circular saw is the biggest one,
which can cut 150 mm deep at once.
Cut the bottom side to be vertical.
Then, make ari joints at the both ends of the beam.
A column will stand on the top side of this beam.
So, draw a marking of the hole
where the column joint will come.
OK, all marking has been done.
Then, start to cut out the beam.
Before that, let me sharpen the blade of the chisel.
First, make a hole where the column will be fixed.
This chisel is called kakunomi.
This can make a 30 mm square hole at once.
I can make the hole by pulling this chisel down three times.
This is an old machine, actually.
Then, make the joints called ari at the both ends.
First one, I'd like to process it by manual saw.
When cutting the top side,
put the saw at 1 mm outside from the marking.
Turn the beam.
And when cutting the bottom side,
put the saw at 1 mm inside of the marking.
Then, the cutting line is on the marking at the middle height.
So, the bottom is thinner than the top side by 4 mm.
After fixing this joint,
that 4 mm difference makes this joint sturdy.
Now, cutting ari shape is completed.
This chisel is called tukinomi.
Adjust the shape by this long chisel.
And shape the edge to connect them easily.
The column will fit at this position.
So, make a 60 mm hole.
I'll process the same joint at the other end by circular saw.
Change the angle of the blade of the circular saw.
It's possible to cut out this joint from side at once.
This time, I process the same joint at both ends
by both manual saw and circular saw.
A circular saw cannot cut out it as accurately as a manual saw.
So, it's necessary to adjust by chisel after circular saw.
So, it takes as long time as cutting by manual saw.
Cutting out it by manual saw may rather be faster.
OK, now whole of this work is completed.
That's all for today.
Thank you for watching my video.
I'll finish this beam by plane later.
I would appreciate you watching that video also.
