How to Make Wood Drawer Pulls | Mid Century Modern Woodworking

Bourbon Moth Woodworking
201 followers
43 Video Views·Jan 8, 2023
Hello! In this video I'm going to show you how to make these cool curved wooden mid-century style
drawer pulls. I got this idea from my buddy Cliff Ham over at Ham Built. If you don't follow that
guy on Instagram you're a fool. Go do it right now. Watch this video. I'm going to show you the
entire process and you might subscribe if you feel like it. Enjoy!
So to start out you're going to need a board approximately one inch thick by six inches wide
and the length is going to be determined by the length of your drawer. You want it to be just a
bit longer than the drawer that you're going to use in combination with this pull. Now on said
board you're going to want to make a line a quarter of an inch down from the top of the board. This is
us laying out where our pulls are going to be cut on this board. Then you're going to mark another
line three-eighths of an inch over from the end of the board and then you're going to mark a line
a quarter of an inch off of that line moving towards the outer edge of the board. In between
those two lines should equal one quarter of an inch and we'll make up the outer edge of our
drawer pull. Next we're going to set up our table saw to cut the cove on the underside of our boards.
So you're going to set your board on the table saw then raise or lower your saw blade until it is
just even with that line that is a quarter of an inch down from the top of our board. Then we're
going to put an auxiliary fence on the top of our table saw to cut a cove at 15 degrees across the
table saw blade. The easiest way to determine 15 degrees is to simply take a scrap piece of plywood
on your chop saw set at 15 degrees and just make a cut. Then you know you have a template that will
get you exactly 15 degrees on your auxiliary fence. To get our auxiliary fence in the proper alignment
we're going to take that same three-eighths inch setup block we used to mark out our board
and with the saw blade raised to the appropriate height we're going to make sure that the end of
our cut is exactly three-eighths of an inch away from the start of our fence. Then making sure that
the board stays exactly at 15 degrees you want to bring the fence over so that it is touching the
base of the board. That will hold the auxiliary fence in place at the front of your saw but you
still have to hold it in place at the back of your saw. Now I have an old ratty outfeed table so I
just put a screw into the table to make sure that it stays nice and firm and isn't going to go
anywhere. Making sure that the blade stays that three-eighths of an inch away from the fence.
Now if you were to try and make this cove cut with the blade at its full height you would either
lose a finger or destroy the board. So you want to drop the blade down to about an eighth of an
inch. You're going to do a lot of small shallow passes raising the blade after each pass. Now the
board is six inches wide which is much too wide for one drawer pull. We do it this way so that we
can actually make multiple pulls at one time. So once you run the board through on one side
flip it around and run it through on the other side. We're essentially making two pulls at the
same time by doing it this way. Remember that after each pass you can raise the blade slightly
and we will keep doing this until we get to our desired height. As you can see in the footage
I am just slowly raising the blade after each pass to creep up on that line that we previously
drew a quarter of an inch down from the top of our board. In all honesty it's probably okay if
your cut is slightly below that line. You just don't want to go above it or your drawer pull
will be too thin. But with our cove cut to the correct depth we are going to redraw a line a
quarter of an inch away from the front of that cove cut. This is going to determine the thickness
that we want for our drawer pull. Then we're just going to slightly draw a reference of what we want
the pull to look like on the front of that board. Then after removing our auxiliary fence we're
going to change the blade angle on the table saw to 15 degrees and we're going to run the board
through that 15 degree cutting off as much material as we can without crossing over our
quarter of an inch reference line showing where our pull is going to land on that board.
It should look something like this. Continuing on with this theme we're going to change the blade
angle once again this time to 30 degrees and we are going to repeat this entire process over again.
A reminder to cut as much material as you can without crossing over that quarter of an inch
reference line as you can see here. And hot dang we are going to do it once again this time changing
the blade angle all the way to 45 degrees. Again removing as much material as possible
without removing any of our quarter of an inch referenced line. As you can see in this wonderful
film footage we are starting to get a nice curve to our board after making those three passes at
the different angles. But we still have a little bit of material to remove. This annoying little
tab here on the end needs to come off. For that we will leave the table saw and we will move to
the joiner. Now I don't have a specific angle for you to set the joiner at. I simply put my board
on there and move the fence until it looks like it is roughly in line with our referenced mark on
the end of the board. With that we've done about as much shaping as we can do on the big machines.
So next you're going to want to get a very sharp hand plane and just start knocking down all those
little corners that you created on the table saw and joiner. Then I decided to take this little
piece of three inch pvc pipe and cut it down to create a curved sanding block. This will help us
maintain the curve on the front of our pole as we sand it smooth and get rid of any remaining
ridges or bumps that might have been left by either the table saw or the hand plane. Now I
should mention that there is a little bit of art or personal preference involved when you are doing
your sanding. There's really no wrong way to do this. You just want to get the look that you are
going for. I noticed there was one more ridge I wasn't happy with so I went back to the hand plane
and then continued sanding and I removed the block, did a little bit of sanding with just
the sanding pad until I was happy with the curve of the overall board. Then I flipped it around
and I did the same exact thing to the other side. Just remember when you flip the board around you
are also flipping around the grain direction so you need to start on the opposite side with your
hand plane than you started before. I almost forgot. But after a little hand planing and
sanding you should have a nice rounded edge on your board and it should look something like this.
With our board all shaped it is time to start cutting out our actual drawer pulls. So the first
thing we need to do is take that board which is essentially two pulls and cut it in half to two
separate pieces right down the middle of the board. Then with our board sitting on a flat surface you
are going to take a straight edge and put a mark just behind where your pull starts to curve.
Then from the back flat portion of your drawer pull you're going to mark the distance to that
mark you just put on the edge. Then you're going to flip around the piece. You're going to find
that same measurement and put another mark on the opposite side of your drawer pull. Then with a long
straight edge you are going to connect those two dots putting a line across the entire surface
of your piece. Next using a tape measure we are going to find the center of our pre-cut piece
and we are going to map out where we want our actual pull handles to land. Now personal
preference is the name of the game here. You can make your drawer pull as big or as small as you'd
like. For these I'm doing a six inch drawer pull in the center of our pre-cut piece. So after
marking out three inches from either side of our center point I'm using a five inch sanding disc as
a template to get a round reference from which we can cut out our handles. Now cutting along our line
that we already drew onto our piece I'm cutting as much of that distance as I can on the table saw
first. You just don't want to go too far or you will cut into your pre-drawn handle and you'll
have quite a mess to clean up. After cutting as much as I can on the table saw I cut the remaining
shape out on the band saw. Just remember to go nice and slow. It's better to cut just shy of our
referenced line and then clean up later rather than cutting off too much. After completely cutting
out our shape on the table saw and band saw I take the pull over to my oscillating spindle sander
to clean up any excess material that was left behind bringing the profile just to the edge of
our pre-drawn referenced line. Then the only thing left to do is to cut the entire drawer pull down
to a quarter of an inch and you should be left with a nice beautifully shaped curved drawer pull
that you can then laminate on the top of a piece of solid stock or veneered plywood and it should
look something like this. To show you what it looks like all glued up here is another drawer
face that I have done previously with it all trimmed down and sanded. As you can see it is
quite a handsome drawer front. Look it even works to open a drawer. Cool. I hope you enjoyed that
video. Now go make yourself some curved drawer pulls and hey if you haven't subscribed to my
channel well get the heck out of here. No I'm just kidding you don't have to leave but maybe
it would be a good idea to just subscribe before this video ends right now.
