Bandsaws are one of the most useful tools to have in the shop. Eventually, the tires on the saw’s wheels will degrade or break and will need replacing. Urethane tires are the best, but they are intentionally undersized, making them difficult to mount. Here’s the best way we’ve found to mount urethane bandsaw replacement tires!
Buy your DFJ T-Shirt, Cap, or Coffee Mug at https.//www.dirtfarmerjay.com/shop
In our shop, the bandsaw is right up there with our table saw. There are very few projects that we work on that aren’t created using one or both of these great tools.
Such hard-working tools need to be serviced ongoing, and parts do need replacement from time to time. In the case of the bandsaw, there are routine items to address, such as blade replacements, blade tensioning, and setting guides. However, sooner or later, the tires on the main blade wheels are going to need replacement. This is especially true if the saw is equipped with rubber tires.
Rubber will eventually dry out, crack, and even break. They are easily replaced and are affixed to the wheels using an adhesive. They are slightly undersized and can easily be stretched onto the rims. The downside is shorter life than the newer urethane tires (“tyres” for our U.K. friends!).
In this episode, DirtFarmer Jay shows you how to install the latest generation urethane tires. They are significantly undersized and need to be properly stretched on the wheels, without putting pressure on any small area of the tire. The tires have a “weld” spot, and that area needs to be avoided when applying tension to the tire. The weld is strong, but it’s still the weakest spot on the tire.
Tires can be replaced on the machine, but we believe it’s a better practice to remove the wheels and work with them off the machine. This also allows for a simple jig to be constructed that will assure an effective installation of the tires on the wheels. The simple jig uses what you likely already have in your shop.
Having the wheels off the machine also gives you an opportunity to clean your machine and to do a thorough inspection of this great tool.
DirtFarmerJay purchases his bandsaw tires at Sulphur Grove Tools. You can visit them at sgtool.com or call them at 904-619-7935. They have a great wheel selection tool on their website. If you don’t see your bandsaw listed, call them and they’ll find the right one for you. That’s what they did for us - ours turned out to require 16” x 1” x ⅛” tires. We purchased our urethane tires from Sulphur Grove Tools, including shipping and tax, for about $47. These are made right here in the U.S.A. Wherever you are in the world, we think it’s good to support your manufacturing base, so if you are in the United States, you might want to take that into consideration, and not just the cheapest price you can find. Simply put, it’s our pleasure to recommend sources that we’ve had a good experience with.
To check out a great little tool to properly set the blade tension on your bandsaw, check out DirtFarmerJay’s review of this clever device:
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. We love having a bandsaw, and if you've got a
maker shop, it's one of the top tools. But there's going to come a time where you need to change the
tires on it. Stay tuned, and I'll show you how to do it with these great new urethane tires.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. We love our bandsaw. It's one of the most important,
useful tools in the shop. However, sooner or later, if you have one of these, you're going
to have to change the tires on the bandsaw. And recently, we put on these new urethane tires.
They are fantastic. They'll probably outlive me. Hey, join me over at the bench, and I'll show you
how we swapped them out. We took our time scouring the internet and YouTube videos to find out the
best process for putting on these urethane tires onto your bandsaw wheel. These tires are quite a
undersized, and if you just try to stretch them on, that's a lesson in frustration, and you won't
get the results you want. This technique that we're going to show you how to put this on
is quite simple and only takes a few general supplies you probably already have in your shop.
One's a piece of 2x4, about 24, 26 inches long. Another is a drill bit that matches, in this case,
a half-inch rod. We also use this piece of metal, which actually comes from a grommeting kit,
and we're going to drive it into here and mount the wheel with it. These create an axle to rotate
that around on. Now, let me be forthcoming here. Notice this was a prototype. We originally had
tried this. The holes were too loose. This was vertical, and you'll see why in a moment,
why it's better to tilt this. So the first thing we did is we took this 2x4. We went over and
drilled the correct size holes in it to match what we have for stock, and you can use all sorts of
different things. You'll also need a short piece of pipe. This happens to be a scrap piece of copper
tubing. You can see it was unsoldered from a job, but you could use a piece of galvanized pipe,
perhaps even some PVC, and you'll see why you're essentially creating a roller surface here. So
how does this work? So the first thing we're going to do is take the wheel, and we're going to place
it over this hole. Notice that the holes were spaced so that when we drive this in,
now I've got a pivot to work with. The second hole is outside about a quarter inch
from the outer edge of the rim of this wheel. Now notice this. When I put this piece of steel,
just happens to be a half inch, you could use a barn spike. Notice the angle that that's at.
There's a reason for that. If this was straight like the first one or leaned in, when we go to
apply the wheel using this technique, it'll continually try to pull the tire off the wheel
instead of placing it on. All right, so here's the next step. You're going to go ahead put this
down here. I'll just use the smoother end down here. That becomes a roller. Then we're going
to take this, put it over that, and then let's locate the splice. There you can see the splice
right there, and as strong as this tire is, that is the weakest point. Even though it's quite strong,
but why tempt fate? Let's protect that splice. So what we're going to do is put the splice right
there and then clamp it. I'm going to take a clamp here and just clamp it right there with the tail
of the clamp going here. Now we've protected that splice, and any tension that's going away from it
is spread out instead of concentrated in one point. Now we're going to rotate this around,
and as we do, let's work the tire into the center below the two or in between the two flanges,
and as we go around, you're going to find that we start to create tension here. This can't pop up
because it's clamped. This angle is helping this come down, so every time we turn the wheel,
we're going to force this tire down into the flanges right there, and as we get closer,
tension's starting to build here. We're going to go ahead and force these down in to get them to
click in. Notice that we're very close now to getting this completely mounted, and as we come
here, you can also come to the back side right there and kind of help get it onto the wheel,
and there we go. We'll rotate around again, force it down, get it centered, and then as we come all
the way around, we're now at a place here where it's going to be on the wheel completely, and
we're about there. There we go, and you're going to have to take some little finessing right here
to get that in, but as you can see it, notice how close it is right there where it's popped in
versus it's riding up a little bit, so go ahead and pop that all in, and when you've got it where
it needs to be, now the next trick is take this pipe right here and start to rotate it up. When
you do so, you're going to have to hold this down. There we go, we're now to that stage right there,
and now we're going to work out this, and as we do, it's going to snap the rod right up next to
the wheel. You can see a lot of tension in it. These tires are very durable, very strong.
There it is right there. At that point, roll it sideways,
roll the end out, let it snap in place, rotate everything around one time to make sure it's
all the way in, all the way around, and it is, and so now let's go ahead and pop that off.
There you go, perfectly, beautifully mounted. One thing you need to do is just run around,
make sure there's no lumps in it, and that the tire is not overhanging the flanges anywhere,
and we did a good job of checking that when we did it. This now is ready to remount on the saw,
tension the blade, and so forth. Use the manual of your saw if need be. You know there's another
thing that really can drive you crazy around the home, and that is when you're mowing the grass
and the grass catcher keeps clogging. Well, check out this video where we show you how to
stop that from happening, and if it has happened, how to get back on the road again. And then check
this other video that we think is pretty doggone good, but YouTube thinks is perfect for you.
Hey, until the next time, this is Dirt Farmer Jay from DirtFarmerJay.com, enjoying the bandsaw.