Modifying a new Axle for my huge Gooseneck Trailer - Break Out The Welder

My Brother Donnie
257 followers
Jan 13, 2025
we went out and we bought a new one
it's a dexter axle it's a
um 5200 pound is what it's rated at
so 52 and 52 on the other
is 11 000 or
10 400 is what it's rated at
but the trailer says it's 14
000. this same axle that come out from
under it
so we're uh we'll see what we got going
on here
i'm going to take these off and take
those springs off
slide the springs up under it first and
then uh i think i'm gonna have to move
these spring perches
um they didn't have the exact right one
so i bought one that's one inch longer
which yeah ideally you want it the exact
same
but i don't want to wait a month on it
so we'll have to grind this off and
move them over half an inch on each side
to get it right so ain't no big deal
we'll just uh grind it off
move it
simple right let's get to it
okay this uh
this bracket's in the wrong spot it
needs to go
that way one inch along with the other
one
on the other side and they both need to
come in they're at 72 inches center to
center i need a 70 inch center of the
center
the hub face is just about right it's uh
like an inch off
which won't bother us any but uh we
didn't want to wait two weeks on a
special order axle so we're gonna use
this one
we're gonna cut it um we're gonna cut
this off
and move it over and i'm gonna try to
use
this bandsaw to do the trick
um i'm thinking i might cut it right
down in the center here
the center is about one inch and then
you know i put the new one on
and then i'll have a nice good surface
there to weld to
but i'm not sure yet what i'm gonna do
i guess we'll both find out depending on
how hard it is to get it off of there
so i've cut it down the center i started
cutting up this side
put up to a point here then i cut across
into that hole
i'm gonna try to tap this side off and
see if it'll come out
the whole trick is i'm trying not to
hate the axle
other than welding it the only reason
i'm doing what i'm doing here
or i'll take the cut torch and just cut
it off and i want to leave this
where i know what's flat there so i'll
have the brakes correct
first dissection i'm going to take
another cut
on this back side come up here and try
to
leave a point there and then i'll run
across the point
so i'm going to cut this other side next
come up
like so and i might even be able to cut
all the way across i don't think i will
be able to
but i might be able to cut all the way
across
and i'm making sure not to get into that
too
i don't want to cut that tube at all if
you look there
i just cut the weld it's got a little
scrape there
but that's just great it just took the
paint off my fingernail won't even catch
it
so we should be good to go
cut a little more on
so we cut the old moved it over
an inch welded them back down
you can see it needed to be right where
the old one was
so i've got this side done and i've got
that side over there done well not done
i've got them tacked in place
i ran out of gas on my wire welder
so in my stick welder there ain't no
rods here for some reason
so i'll take it to the house and weld it
up i got another welder there
the house and if that won't do it i'll
run to the other
side and get another one and welded up
but
i tacked it in with no gas so
i got four attacks ain't going anywhere
but got that done and um everything
looks to me
it should be on the same plane there
along with that one down there
so we should be good to go
[Music]
damn he's got another one at his house
fixing a little light to it i'll show it
here in a few
damn he knows how to do everything
it's gonna be hard to get up in there
somewhere it's gonna be hard to get up
in there
so i'm gonna get up in there i think
it's gonna be easier
match up perfect that's when you know
you're doing it right
two black spots that's where the
ember falls in your hand and you just
keep right on getting it
so we got that side welded
we got it welded up in there got a
little welded over there
we've got that side welded and
now it's time to stick it up in there
got it up under here
so now i gotta roll it forward a little
bit
get the shackles back on
um and the bottom plate back on
and then get it jacked up and get that
back bolt in there
so this is gonna be fun
well we screwed ourselves
bracket goes there the bolts can't go in
because we left that little piece to
make sure we had it on the same angle
so the bolt sits right on top
so now
we've got to cut that out but i think
what i'm going to try to do
is uh put it in like it sits
and uh get it up a little bit here
where i can slide under there with the
sawzall and just cut it off
it's going to be easier to cut it from
the bottom i believe
but i got to get it up in there and
there's can y'all see any of these mats
there's a half million that's eating me
up
i think y'all can see it but anyway
it's always something so we'll get on it
again
well we got both the tires on this side
and uh
the hub face you know i told you it was
an inch or so difference
right there's the difference you can see
it this tire sticks out
i don't know maybe a half inch more
than that tire maybe an inch more but
it'll be fine this ain't going to touch
it we got plenty of clearance
and we should be good to go now we got
to do is get over there
and put that whole side together we've
done nothing over there yet
so that's next on the agenda
here's a little trick we can't push the
edge of that spring up in there because
we're hitting the outside here
just lay your boat in there
and then you jack it up
and then it'll push right through and
you'll be good to go
[Music]
okay i'm down here basically i had to
jack that side up
because it was already attached now i
jacked this side up
and i had beat this axle back this way
then i had to beat the spring in this
way and it fell in
to the pin now i'm going to put this on
there
and put my u-bolts in
and bolt it up
okay we got our u-joints in
here's a little piece we had to cut out
it went in there
it was right in the way it went like
that
it was right in the way of where you
joined or another usual
u-bolt so we got those cut out on all
four sides obviously
and now we've got them in we've got to
tighten them down here
i've got that one pretty tight by hand
but the other side we need to tighten
down i'm going to jack it up a little
farther where i can get my milwaukee in
there to tighten them up
it's laying out there i'll tighten them
for up real quick
and we'll slap a tire on it and set it
back down on the ground
voila we have our back axle
it's in it's bolted down it's lined up
it's got tires it's got rims she's ready
she's a little wider you can kind of
tell there
but it'll work
i don't believe it'll touch i don't
believe there'll be any problem
see this one see that
the tire is offset more
i could turn that rim around and make it
suck in that much more
but we should be good
give us a thumbs up subscribe to the
channel
thank y'all we'll catch you on the next
