Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine discusses and displays his techniques for achieving desired results in matching contemporary repair work to the colors of antique furniture. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, call us at (207) 222-2266, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
I'm Tom Johnson, Thomas Johnson Antique Furniture Restoration from Gorham, Maine.
This is a video in a continuing series where we try to answer frequently asked questions.
It's a companion to the video I made called Staining Wood,
where I show the different types of stains I use to stain bare wood.
In antique restoration, color matching is the key.
And in fact, when you look at an antique, most of the time the wood was not stained at all.
The color is the natural color, but been affected by age and numerous environmental factors.
So when you're repairing an antique and trying to match that color,
staining the bare wood would rarely achieve the desired effect by itself.
That brings us to today's video, where I'll discuss the
techniques I use to achieve the desired effect.
The word glazing typically means using a glaze coat.
And a glaze coat is mixed with different oil colors.
But I'm going to call glazing anything that we do over a sealed surface and between coats
to affect and change the color.
So over the sealed surface, I may use glaze.
I may use regular oil stains as a glaze.
I may use dye stains over the sealed surface.
And quite often, we use toners.
Frequently, people ask, why do I seal the wood and then use these stains for coloration?
And you have to think about how the wood of the piece of furniture achieved its present color.
It did it from age, oxidation, which is, I guess, is age, other factors.
But it wasn't stained.
And if you apply stain to the wood, it brings out the grain.
It does different things to it that it just will never match.
So sealing off the pores prevents that stain from bringing out the grain more than desired.
And it also allows you, using these other techniques, a lot more flexibility and ability
to reverse what you've done if it's not correct.
So in this real-life example, you'll see where I take a walnut carving.
And although I do use stain on the bare wood in this case, I seal it and then do what anyone
would recognize as conventional glazing, where I use, actually, asphaltene mixed in a glaze coat
to achieve the desired effect.
So asphaltene is exactly what it sounds like.
It's some kind of tar.
And I will mix it into a clear glaze coat.
I've already done that.
And I'll put it on, try to recreate the distressing I see here.
So I've mixed a little of the asphaltene in some glaze coat here.
The glaze coat is just a medium.
It's thick.
The kind I buy is extra thick.
And it's made just for this purpose, adding oil colors and things like that.
In this case, we added the asphaltene.
And now I'm going to apply it to my little piece here.
I will put it all over the entire piece, wipe it all the way off.
And then I'll go back and try to mimic what I see in the original, leaving bits here and there.
So that was a good example of conventional glazing.
This next clip shows me using dye stain over a surface sealed with two coats of tung oil varnish.
This is a good example of how you can use dye stains during the refinishing process.
This is a nice cherry chester drawers, but the top is veneered.
And on the end, you can see the end grain of the solid core.
I'm not staining the cherry.
It's going to be left natural.
I put on two coats, two thin coats of tung oil varnish, seal everything off.
Now I'm going to sand the end grain and tape off the cherry.
So now I'm going to use a little bit of medium brown walnut dye stain.
It may seem funny to use walnut, but I know that this has a lot of orange in it.
And it's not exactly this color, but I think it'll get me where I need to be.
And I have a rag at the ready.
Now I can make it a little darker if I like, or even it out a little bit
by putting some stain directly on my rag here and patting it along.
If I felt I had a little bit too much on, I can take a clean rag, a little bit of alcohol,
add some of the stain on.
I actually kind of like this color.
I don't know, it might be too light.
Better too light than too dark.
I'll put another coat on this whole thing, and if it's too light, I can always do this again.
If it needs a little bit more in the corner or a little bit more at the end,
I can take my brush, add a little color.
If it's a little bit streaky from my rag marks, that's okay.
But it kind of makes it help it look like wood grain,
even though technically the wood grain is not going in that direction.
I'm going to let this dry just a little while,
and then I'm going to sand the rest of the piece of furniture
and put a coat on everything and see how it looks.
Okay, I've got this all sanded, ready for a coat.
I can preview my staining job here with a little bit of paint thinner.
I think that looks good.
It's a little browner than the cherry,
but when you're trying to match something or get it to blend in like this,
you definitely want it to be less red than the surrounding area.
That way it doesn't stand out.
So this looks good.
I'm going to go ahead and brush a coat on.
So that showed one way to deal with end grain,
which is a good example, though, of how with end grain,
if you stained it, if you stained the bare wood,
it would just instantly be too dark.
So you really need to seal it off
and then go over it with a glaze or dye stain that I used
or anything that suits the situation.
So in this clip, I have a highly figured tabletop.
I know it needs color.
I don't want to stain the bare wood.
So I added stain to my sealer coat of tung oil varnish.
And when that didn't quite do the trick,
I, in a subsequent coat, actually diluted it a little bit,
but I still had stain in the finish and brushed that on.
So that's a toning effect or shading effect to get it to the color I want.
But layering color like this also greatly increases the depth of the figure.
Okay, this top's all sanded now with 220.
Now, I noticed when this top came in,
besides all the obvious water damage, that it was really bleached out.
It must have been in a really sunny location.
The top is substantially lighter than the base.
And I'm going to put a little paint thinner on here
just to see what the color is and compare it to the base.
The top is really light and I can really see a huge difference here.
So what I'm going to do, I'm going to experiment a little bit.
I have some stain here.
This is pigmented stain from a local manufacturer.
It's just brown stain.
It's just called brown.
Here's my tung oil finish.
And I'm going to add a little stain to the finish.
So maybe on the first coat, we'll be tinting a little bit.
Now, bear in mind, my goal is not to match the base.
And in fact, in any piece of antique furniture, especially tabletops,
the top should always be lighter than the base.
But I want to take it a little bit more in that direction.
It was a little bit too washed out.
I'm going to try a little bit more.
Okay, I've let it soak in for a few minutes.
And I just wipe it off.
All right, let that dry overnight.
All right, that first coat is dried overnight.
It doesn't need any sanding or anything.
It's pretty well soaked in.
Now time for the second coat.
And I think I'll use a coat with some more of that stain in it.
This is what I have left of the tung oil with that brown stain in it.
And I'm just going to add more tung oil, not any more stain.
I like the color I was seeing.
When brushing a coat with stain in it, you've got to put on a really even coat.
It can't have streaks that you wouldn't see with a clear finish.
I'm anxious to see how this color looks with the base.
I think it looks really good.
It's the same color as the base, but a little lighter.
It's just what I wanted.
All right, now I'll just let this dry overnight.
Okay, so this is dry.
It feels like it needs sanding.
You can't sand a coat that has stain in it.
It would make that coat uneven or your stain uneven.
But luckily with tung oil, you don't have to sand between coats.
I'm just going to blow this off.
And then apply a coat of clear tung oil.
The next clip is a continuation of a clip we used in the staining video.
And it shows a contemporary chair where I used dye stain, then oil stain,
which is a good way to achieve kind of this factory look.
Then sealed it.
The color was close, but I needed to tone it with aerosol toners to bring it in where I wanted it.
I've allowed the shellac to dry overnight.
And so now I know I've got to do some toning.
I can see from this sample I've been using that I'm definitely a little bit browner.
What I do is I have a piece of black construction paper here that I've drilled two holes in.
And that's what I use to check color with.
I place these on the two things and you can really see what you need to do.
And actually, I knew starting out that this sample was lighter.
And that was fine.
My color is good, but it's way browner.
It needs to be redder.
But what really matters is not this piece, but the rest of this piece.
So I'm going to cut the paper back here and compare what I've got to the crest rail.
So right away, I can see how much browner this crest rail is and the rest of this back
compared to my sample.
I knew that going into it.
But I wanted to use a sample that was lighter just so I didn't go overboard.
I think maybe I just need a little mahogany toner on here.
So I'll seal this back up, sand my shellac, and try toning this a little bit and see how
it looks.
I'm really going to sand lightly with just some 500 gold.
I don't want to pull up any color that I already have.
You can see color on the sandpaper.
So that's why I've got to be really careful sanding.
I've got a brown mahogany toner.
Now let's see what it looks like.
It's looking okay, I think.
I may have to let this dry to see for sure.
And although I'm a little unsure of the color, maybe a little browner, I still like what
I see.
So I'm going to go ahead and tone everything with the brown mahogany.
Then I'll decide what other kind of toner I need to use.
I've let the toner dry.
And so I'm looking at my color.
It's still different.
It's still a little lighter.
But it's actually really close.
One of the difficulties is that the factory finish here is a little more opaque looking
than my finish.
And it's very, very flat.
That's going to make a difference, too.
I pulled back the paper on the slap.
And the slaps are even lighter than the crust rail.
So I'm thinking that I'm okay.
I'm not going to mess around with this color anymore.
I'm going to bring one of the other chairs from the set over here.
Take a look at it, too.
Yeah, I'm going to call that a day.
The colors are kind of all over the place.
And I'm right there within the spec.
So it's good.
Now, all I need to do is pay a little bit more attention to my new piece of wood right
here.
I'm going to take that off and color it a little bit.
Okay, I've sprayed about, I don't know, maybe eight coats on all this, both sides with my
flat aerosol.
And it looks good.
It's nice and low luster, and it looks like a factory finish.
So now I'm going to remove all my tape and stand back and see how it looks.
Yeah, I think the color looks pretty good.
It looks really good with the crust rail.
These are lighter, but that's okay.
They're all in the same ballpark.
I'll know better when I hold this up and compare it to some of the other chairs in the set.
Comparing this to one of the other chairs, I think it looks really good.
So I think I can now proceed gluing the chair up.
As you saw in that clip, toners are invaluable to really fine-tuning your color.
In the next clip, you'll see where I've repaired veneer on the edge of a table.
And as I approach the final color, I've got colors all over the place, both from my new
work and old work.
And you'll see how I use a toner as the last step.
It just kind of brings everything together.
Okay, I finished sanding with 220.
And yesterday, I glued up a piece of the same veneer that I used for the edge.
And I've sanded it to 220.
And I'm going to try some stains out on it.
The first stain I'm going to try is some white gold milk.
The color is good.
It's a little light, but I like light.
I'd rather have light than too dark.
I think I may try this on the table itself.
And if it's light, that's okay.
I'll seal it with shellac and then add a little more color to it.
Okay, I've let the stain dry for a couple minutes.
And now I'll wipe it off.
I'll kind of pat it off.
Remember, the stain was light, so I don't want to wipe it off too much.
Now, this is fast-drying stain.
I'll set the timer and let it dry for an hour.
So the stain is dry.
And so now I'll apply a coat of shellac.
And first, I'll put a coat on the sample.
Well, that looks pretty good.
I was hoping to have a little bit more of a yellowing effect.
It doesn't seem to have much effect.
But I'll put my first coat of shellac on, and then I'll see what I can do about the color.
It's not changing the color too much.
The shellac is not.
But my new wood is lighter than the old wood.
And that's what's important.
I'll go back after the shellac dries and then figure out exactly what I'm going to do to
blend it in.
The initial coat of shellac has dried.
So now I've got to add a little color.
You can see my new patch, it's a good color.
But the wood surrounding it is a little bit darker, a little bit grainy.
And that's good.
So I'm going to try first to add a little bit of raw umber color to some shellac and
apply that just to the patches.
First, I'm going to go over this with a 500 paper just lightly.
Maybe a little too dark.
I'm not sure.
I can always add some more shellac.
But I'm going to try it anyway.
I can always wipe it off.
Yeah, it is a little dark.
But by then wiping it slightly, it gives me a little bit of that grainy effect and
blends in pretty well.
In fact, when I stood up, stood back a little bit, I had a hard time even spotting where
this was.
So I think I'm just going to keep going like this and wipe it off as needed.
Actually, I seem to have just the right amount on the brush now.
And it goes on pretty well without even the need to wipe.
As I work my way around the whole perimeter here, there's lots of areas, even where I
didn't work, the old veneer where there's color variations.
There's a lot of color variation in this edge.
And so I'm able to even go and touch up some of these light spots too and take the curse
off of them a little bit.
A lot of different areas.
The touch-ups look good.
It's funny, when I'm up close like that, I can really see a lot of variation.
When you stand back and look at it, it looks a lot better.
Thank goodness.
So what I'm going to do though is I'm going to take some light golden oak aerosol toner
and I'm actually going to go over this entire edge.
I think that will really pull it all together.
That was definitely a good move.
Some of these areas I may hit a second time.
I'll let this dry a bit and then I'll check it again and hit it wherever I think it might
be necessary.
It's really looking good now.
Okay, I've let the golden oak dry for about a half an hour and now I'm going to spray
it again but with clear gloss lacquer.
So there you saw how I used the yellow toner just on that edge to kind of bring everything
together.
In this next clip, I have new wood.
I've made new pieces for an 18th century antique.
I stain the pieces with the dye stain, seal it with the aerosol shellac, glaze it with
the umber glaze, fix that glaze with the aerosol shellac, and then use a green toner to kill
the red a little bit.
Okay, I've let the dye stain dry for about 45 minutes and now I'll seal them with shellac
and then once they're sealed I'll decide if I need to do some more color work.
Yesterday evening I sprayed these with another coat of shellac, let it dry overnight.
You'll see that my samples here, my new pieces rather, are much redder even though I stained
with Van Dyke brown stain.
That's to be expected.
All wood, especially mahogany, loses its redness as it ages.
So anyway, I'm going to cut back this shellac with a Scotch-Brite pad and then I'm going
to glaze it with the raw umber glaze.
So after using the abrasive pad, I just went over it real lightly with a little 500 to
really cut the fibers and make it really smooth.
You're always worried about cutting through the color, you know, down to the raw wood,
but I managed to do that and get it really smooth.
So the glaze coat, glaze is just some medium, some oil-based medium, and then it's got oil
colors in it.
And in this case, raw umber, which has no red.
So the nice thing about glazing, it's just very versatile.
It, you know, it does add a little color and this, in this case, adds color and I hope
decreases the red.
It also darkens up the corners and shows little defects and stuff to help make this look older.
And you can, you know, you can control it.
Because it's on top of the finish, you can wipe it off complete, you know, almost completely
if you like, just leaving it in the corners.
Or in this case, I'm wiping it lightly, very lightly, to get off some of the excess.
And then taking a dry brush and just sort of evening it out.
But I'm leaving a fair amount of glaze on here.
It looks good.
It helps it look like the old piece that I'm sampling to.
And then when I'm done, I'll let these dry for an hour or two and I'll spray on another
coat of shellac to fix this glaze.
You can see already that the color's a lot better.
So I gave the moldings another good coat of shellac.
They're still a little too reddish.
They're not bad, but they're redder.
And what I have here is a green toner.
It's actually green.
And I'm going to mist some on these moldings, see if I can kill the red a little bit.
And that definitely, just that little misting took the red away.
I'll let that dry for a few minutes.
Then I'm going to give these a couple coats of satin lacquer.
So I hope you've seen in this video and my previous staining video, everything that I
use in my color work.
And there's a lot of different stains, a lot of different techniques.
There's no one set way to do things.
We're constantly bobbing and weaving.
Every piece of furniture is different.
It's a very good idea to get yourself a color wheel.
Sometimes it's really obvious if a piece is too red, where you tone it with green.
But you may not know if that piece is too yellow, that you tone it with purple.
Color wheel comes in handy.
Good luck.
Everything you need is right at the hardware store.
I hope your project comes out looking pretty good.