Learn how to make a circular saw guide for quick and accurate cuts. A guide for your circular saw is good for cutting all sorts of sheet goods and shelving material. Inexpensive and simple to build, you’ll use this DIY circular saw guide again and again!
Compact saw guides and track saws are a must-have in the woodworking shop. Even with a table saw, these devices allow larger panels and sheet goods pieces to be efficiently and accurately cut down to smaller needed sizes by bringing the tool to the material rather than the material to the tool.
A saw guide and a true track saw are two different things, but they are similar in that they are designed to create accurate cut lines either lengthwise or crosswise on the material.
There are several track saw products on the market today, ranging from premium high precision tools systems, such as Festool®. There are other less fully-featured products that give much of the functionality of higher grade systems but are made of less durable materials, or are not fully commercial systems. Kreg® offers such a system.
One key feature of a genuine track saw system is an integrated saw base that interlocks with a guide rail that assures the saw closely follows the path of the rail without lifting or shifting.
A saw guide is set up differently in that an “off the shelf” saw (outfitted with the correct blade for the task at hand) can be used with the saw being butted against the edge of the guide to steer the cut. Reasonable accuracy can be had by making sure that moderate pressure is maintained on the saw against the guide so that the cut doesn’t wander. The problem is that just a few seconds of inattention can ruin the cut and send you on another trip to buy more material.
In this episode, Dirt Farmer Jay will show you how to make a saw guide that will assure the saw stays on course, is easy to position and clamp in place, and can be made in various sizes to commonly cut sheet good sizes. Only basic materials are needed. The version DFJ has made uses a DeWalt® 6-½” 20 Volt battery saw with a 60 Tooth Laminate cutting blade.
While the saw base will likely need to be trued, and there will be slight play in the dual guide set-up, the resulting cuts will be accurate enough for pieces to be sized correctly and edged in such a fashion they can be assembled tightly. For a guide that allows you to cut 24” wide material, you can expect to spend about $25 (not including the saw!).
Let’s give credit where credit is due - the inspiration for this tool came from this episode at “The One Minute Workbench” - you can watch it yourself at https://youtu.be/H0BZLbW1lvQ. We added a few little features and have been really pleased with the results for a very modest investment!
While there may come a time where a fully-featured track saw makes sense for your shop, you can get started with this great shop-built tool - and you can JUST DO IT YOURSELF!
Follow us on Social Media to know when we’re building projects or releasing new episodes!
You can help support this channel by buying our merchandise or supporting us on Throne or Patreon! Merch: COMING SOON! Patreon: https://www.patreon.com/dirtfarmerjay
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. We love having a circular saw like this in our
shop to cut down sheet goods. And whether you're using a cordless model or a corded type,
these are really handy saws. But if you really wanted to work harder for you and to get great
straight, crisp, square edges, then you need a saw guide. I'm going to walk you through in
this episode how to make this saw guide, the kind of different materials that you can use,
and what the difference is between the saw guide and the saw track.
Stay tuned and I'll tell you all about it. Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Well, we love having this saw and we've really gotten it to the next level by creating this
saw guide. And I'm going to show you the different materials that you can use to construct it.
In this case, we simply use some clear pine that was really stable and straight and beautiful.
And we used tempered masonite, was the actual brand masonite. And tempered is really smooth
and hard on the other side. And besides, it smells good when you cut it. It's not the untempered
side or type, which is kind of fuzzy and soft. This is pretty dimensionally stable. So I use
that. This is about a three sixteenths, a little bit thicker than that for the base on the saw guide.
You could also use these types of plywoods where you've got solid core plies in here,
and there's a lot of plies. These are Baltic birch type of plywoods,
very dimensionally stable, a little bit thicker, but very smooth. So whatever you've got on hand,
and I even know of a gentleman that built one of these using plastic on the bottom,
a really nice thick plastic for dimensional stability and being able to mill it.
Now, before we get any further, I wanted to give credit where credit is due. I
initially got the idea from this, from the One Minute Workbench. And I put a link down in the
description below. If you want to check out his video and his channel, feel free to do so. He's
a great creator and he certainly inspired my thinking. And I came up with a couple other
little enhancements or things that I wanted for my template or for my guide. So we'll go through
these. So I'm going to take you step by step, but before we do though, I'm going to ask you a favor
really quickly. If after you watch this, you find this video to be helpful, won't you like it?
And better yet, won't you subscribe to our channel? And when you do, ring the bell,
because then you'll get notified approximately every Friday of another great video episode
in the home, the garden, vehicle care, being a great homeowner, Maggie's kitchen,
and great heritage cooking. Well, you'll just learn how to just do it yourself. And while you're
at it, check out our great new website at dirtfarmerj.com where our new merchandise line is
coming on. There's a great there Maggie's blog. There's all sorts of stories that are out of the
kitchen and great recipes and resources you can download. And it's a great place to interact with
us. Well, let's get to it. Let's build this guide. So let's look at the basic materials you need. So
I just started out with a piece of masonite, as I showed you, and some one by two clear pieces that
were straight and ready to go to work for us. The dimension of the masonite was about 40 inches
long. And I found out later on that gave me the cutting width that I needed for common size of
cuts here that I do in the shop. More about that in a little bit. Now, so after you've got your
straight stock and you've got your masonite, the first thing to do is to glue on and affix one of
the edges along the factory edge. And I checked that edge to make sure it was true. Just because
it came to the factory doesn't mean it always is, but in this case it was. And so I was able to use
the straight edge and the good old finger pad to feel the difference to make sure it's absolutely
straight along that edge. And I put down a generous bead of glue, clamped it on, flipped it over, and
used my pin nailer to make sure it wasn't going to slide around until that glue set. And so that
was the first thing that we did. So now came time to do a little bit of dry fitting of the second
guide. And to do that, you use the base of the saw itself right there to determine the width there.
So I place the saw against the glued on edge that I've already done, and I dry fit the other one on
the other side to give the approximate dimension. Before we go forward, I just want you to see real
quickly what saw blade that I'm using there. It's a six and a half inch, 60 tooth blade that is
designed specifically for melamines, which we're actually gonna be doing in this project. But it
also allows just much smoother cuts on plywood and that sort of thing. More teeth in the work and
coming out of the work and little distance sharper teeth really make a difference on reducing
splintering. So that's the blade of choice for me. You can also get that blade in 40 tooth. It'll
work reasonably well. It's only a few bucks more. Get the 62. Now, when I started to put this
together, just out of curiosity, I wanted to know what the width of cut was going to be. How long I
could get of the saw into the work. And so I went ahead and put it in the end blocks in against
the glued in piece. Again, dry fit them. And then I put the saw down and lowered the teeth down till
it's touching the surface of the base. And I put literally a sharpie marker there just as a
temporary marker to show where the start of the cut was and then the end of the cut and then
measured the distance. And what I found is that this guide was going to produce roughly 24 to 26
inches of cut. It turned out afterwards that it was closer to 26, which is perfect for all the 24
inch wide stock that I cut. This in the background, you can see right here is all 16 inch, but there's
a lot of 24 inch in this that we're working as well. And you don't want to be in the middle of
cut repositioning. Another great thing you can do with all this is make different lengths. I plan
to make another one later that's about 54 inches long so I can cut 48 inch wide sheets. And if I
get it down to that size, I can probably run it through the table saw so I don't need an 8 foot
plus straight edge. At least now you may, but you can use the same basic construction and scale it
up and down. After I determined the width of the capacity, or let's put this the length that I
could cut through the jig now, it was time to go ahead and getting close to put in the second
guide rail, the one to the right, that would ride along under the motor side of the saw.
And what I did there is butt up the edge of the base against the left guide, and then I used a
on each the front leading edge and the trailing edge of the guide on the opposite side
to create a little bit of wiggle room so that the saw would slide through there. And at first,
all seemed really well. Things were going well, and I slid it back and forth a couple times.
And then I started getting some little jams here and there. I looked for straight,
had a little slight warp. You'll see in a subsequent picture a clamp that's kind of
going sideways, and that was to help address that with slight pressure. But here's what I
really found out. The edge of the guide, these are construction saws. They're not fine trim saws
like a true track saw, like from Festool or something like that, which are high precision
tools. These are for in the field and the construction trades, and so they're not going
to be super fine-tuned. And so what I needed to do was find out where I had some lumpiness,
and you can see where I put a straight edge along the edge, and you can see the slight
gappiness that's along one end, the closest to us in the picture. And so what I did is actually,
because it's a soft metal, I can actually run it along my stationary belt sander,
and I trued up that edge. It took several passes, a little trial fits back and forth.
And then you can see here, when I put the straight edge on again, we had a beautiful
true edge, and that solved the problem. Now we went ahead and dropped it back in in the guide,
put the cards in around it. And here, I'm just going to show you kind of a swing-around shot,
so you can see the front and back leading edge and trailing edge of the base with those spacers
and how that was all done. And once those spacers were in place, and I did one more
run up and down to make sure it all worked, then we went ahead and glued that in place, pinned it.
Once the guide was freed from all the excess material, I went ahead and laid out in the back
those reinforcing screws and did a nice pattern. Why not do them in a nice setup, do a little bit
of craftsmanship there, so you enjoy it every time you pick it up. And we laid out in a nice
repeat pattern around there, took it to the drill press with the appropriate size countersink bit,
and went ahead and drilled those in. Then I just took the opportunity to use a sanding block to
knock off all the edges, make it easy on the hand, and to soften the edges so they're more durable,
and got that all done. Then went ahead and drove all the screws slightly below the surface, and
that's the reason we countersunk them the way we did. But I made sure that there were no screws
standing proud, and we got all that in place. The next thing you can do is to run a very slight
score cut that just helps you to position where you want to drill the sight holes. If you're using
a Forstner bit, you don't really need to do this because Forstner bits are also guided not just by
the center point, but by the rim of the drill bit. But I like to have both ways to do it, so I went
ahead and just set this saw just slightly below the surface of the base, put it into the guide,
and ran it along there. And you can see the resulting line that's just barely cut along the
surface. It becomes a layout line. And to highlight a little bit more, I just took a metallic sharpie
pen, a silver or gold one, laid it in the line to make it stand out. Now at this point, I went and
took it over to the drill press, and using a one-inch Forstner bit, just laid out a line. I
didn't center them directly on the line. They're off-center a bit. That's just preference. If you
want it just perfect down the center, do that. But I went ahead and drilled out each one of those
after I laid out a nice pattern. So there are five holes, one on each end, equidistant in, split to the
middle. Again, that's preference, just so when you pick up the tool it looks cool. But I got those five
sight holes done, and now the jig is ready to use. Here we go. All right, let's get to work here and
show you how we put this fixture, this guide, to work. There's one important thing to know about,
in case you didn't know this, about circular saw, how they cut. When they're called a circular saw,
it's because they're not reciprocating straight up and down. The path of the teeth is in the
circular motion, hence the name. But that brings up an important point here. When this saw is running,
it's turning in that direction. What that means is on the trailing edge back here, where the
kerf has already occurred, where it's already been cut, the teeth are encountering or going by the
work in a downward fashion. However, on the leading edge, as you're going forward in the work here,
that means that the saw is cutting from the underneath and coming up through the work.
That means it's prone to chip out right there. So one of the tricks that many carpenters do when
they're doing finish work is, number one, use as high a tooth count as you can. Number two,
is to put the good side of the material down because it won't chip out as it's coming up
through it. The back side of the material would chip out or would be more prone to it. There's
ways to fight that, cutting through tape, scoring the line and all that, be that as may. In this case,
what we're cutting here is a melamine board. There is no bad side. Both edges or both faces
are going to be showing. So what you have to do is be very careful about cutting that. So the first
thing that we do when we run this through the guide is I have lowered the blade just deep enough
that it will score the surface of the material without going all the way through and minimize
chip out. And then we'll take a second cut through it, full depth. Now, one other thing you got to
see really quickly here is around the side here. Whenever you're doing this material, I love
stacking material on material so you're not handling it multiple times, but you've got to use riser
blocks to raise all this off so that when your blade is below the work here, that you're not
scoring the faces of all this and everything's clear. It also gives you clamping room that you
need to clamp on the guide. All right, well, let's go ahead and make this cut here. This particular
layout, I need a six foot piece. And this will be the third one of these we're cutting. But I'm
just going to go ahead and do a layout. I always do two layouts, even though I'm going to be using
a square. And if you really want to go overboard and really get it accurate, do what's called the
three witnesses type of approach. And that is lay it out three times. And then what we're going to
do, so I have three 72 inch marks from the left end. Now I'm going to throw on my square and I'm
going to bring that right up there. And you know, if those three witnesses line up, I got it. So you
can see right there. Look at there. One, two, three. So let's go ahead, keep that pencil nice and
vertical and sharp. Let's lay out that line. We now have our line to cut. Now we're going to go
ahead and put on our guide. Now, a couple of things I did on this guide real quick. I also should write
this. No clamp. You don't use the clamps on this side because that's the side that the saw motor is.
And when you go to clamp or to run it through, if you've clamped it there, you're going to collide
with this. Don't ask me how I know that. But anyway, you're going to go ahead and clamp only
on this edge. So now what we're going to do is we're going to line up our guide and I'm going to
have you look straight down if you can. That's a little bit of a weird angle or down the guide
until you can see it. And we're just going to line up those lines using those holes to tell where the
line is going to be here. And if you can, in this case, I'm actually going to back this up till I've
got three lines showing again. And I've got one in the middle, one there, one down at the bottom.
Look at that. They're all lined up. Then we'll go ahead and slip a clamp on it. Clamp it down nice
and tight. And when you do, you know, depending on what the material is, you may have to put a pad on
or piece of paper. This is pretty durable. I'm putting moderate pressure to stop it from sliding.
Do another check. Let's go ahead and throw another clamp on it here. And there we are ready to go.
One final. It is a beauty. All right, let's go ahead and we're going to do our scoring cut.
So how do we do? Well, you take a look for yourself here and see what we've got here.
That is, I'm going to put it together. Look how clean that is. It's pretty doggone close.
And if I pull this apart, chip out is really minimal and it's interesting. It's more on the
wayside than over here. This is a good cut for the amount of investment. The investment to build
this tool is around $20, $25. Now that brings up another point really quickly. What's the difference
between a guide and a true track saw? Well, you're looking at two different things that have similar
functions. Both are designed to put straight edges onto either sheet goods or to take something down
to size. But in the case of track saws, a lot of times those are actually used to edge rough lumber,
especially hardwoods and that sort of thing. So there are more precision. The track saw though,
the big difference is, is the interlocking base that rides along in the track that doesn't allow
to lift, to rotate, to do all sorts of distortions. It's very precise. And so this depends on this
guide here. That depends on you keeping the saw down on the track. And if you're using a single
sided guide, which many people have done, I did many years as a trim carpenter, building out
cabinets and all sorts of things like closets. We would use a single edge guide, but that depended
heavily on you paying attention and keeping that saw to the left as you cut. Well, the track saw
takes care of all that, but the price point is significantly higher. Now, in the meantime,
you can build these kinds of guides. They're not an absolute replacement for, but they're somewhat
a substitute that will get your work a lot closer. They're kind of an entry level. You'll see whether
your work and the method, the way you work really lines up using these kinds of devices. And perhaps
down the line, track saw is a wise investment for you. And there's some moderate level ones like
from Kreg tools. There's a high end ones from Festools and other that are coming on the market
right now. If you have a device like this or some insights you'd like to offer to your fellow
readers or back to us, then feel free to do so in the comments below or over on our website at
DirtFarmerJ.com. If you found this video to be helpful, won't you like it and better yet,
subscribe to our channel. And when you do ring the bell, so you'll be notified
approximately every Friday of great video content about things in the shop, being a great homeowner.
We can just do it yourself, taking care of appliances and all sorts of home repairs
and some great heritage cooking over at Maggie's Kitchen, great blog content and recipes over in
her section on DirtFarmerJ.com. Until the next time I've got some cutting to do. We'll see you soon.