There are many types of clamps for the shop, but parallel clamps are becoming really popular, even though they are a significant investment. Are you good for YOUR shop?
Buy your DFJ T-Shirt, Cap, or Coffee Mug at https.//www.dirtfarmerjay.com/shop
There’s an old adage in woodworking - “one can never have too many clamps.” This sentiment seems to have come from the experience that when it comes time to clamp up a wood project, it’s easy to use up a lot of clamps doing the job well.
I have a lot of clamps, but will probably continue to add more as the need arises. My inventory ranges from various sizes of “C”, “speed”, spring clamps, as well as “Pony” pipe clamps, originally made famous and commonplace in many a shop by the Jorgensen company.
In the last few years, I’ve noticed both in woodworking journals, shop YouTube videos and woodworking shows that many of the craftspeople are using parallel clamps. I decided to check them out, and I’m glad I did.
These types of clamps are significant investments. The brand I purchased, Bessey®, is available ranging in sizes from 12” (30cm) to 60” (152 cm). At the time of the production of this video, the 12” was $42, and the 60” was $68, with all the sizes in between priced between those two. These are the K-Body REVOlution line with fixed clamping heads (they do have movable head models so you can balance the weight of longer clamps when clamping small objects than the capacity of the clamp).
There are other parallel clamp brands available as well, such as Jorgensen®, Jet®, Gross-Stabil®, Woodcraft®, and Stanley®.
With such a significant price, why would I buy them, and why should you consider them? Two big reasons. First, they are called parallel clamps because the fixed and movable clamping faces are parallel and very strong, with very little deflection as adequate force is applied. This makes for a flat assembly. Second, you can simply put these clamps on a flat surface and load them up. They stand upright on their own just fine, and placing “alternating” clamps from the other surface is easy.
What are the disadvantages? Cost is significant, so these are only justifiable if you are going to use them ongoing. Second, they are HEAVY. There is a lot of material in these units, including the main bar. So you’ll want to have the best sizes for your projects on hand. Third, like any new tool, you need to adapt them into your workflow and setting. They do take a bit getting used to, but that’s no big deal. They need to be stored efficiently - we think hanging them up is best. You can get ready-made racks for this purpose from Rockler®, or you can make your own. Heck, we’ll likely do a build of racking that stores them efficiently, but makes them really accessible for day-to-day use.
Where are Bessey K-Body Clamps made? It took some research to find this out. Bessey is a German company, but these clamps are made in PRC (Peoples Republic of China). I try to support the economy of the country I live in (U.S.), but I was not able to find any of these types of clamps that were made in the U.S. If someone has better info, let me hear from you!
Buy your DFJ T-Shirt, Cap, or Coffee Mug at https.//www.dirtfarmerjay.com/shop
Follow us on Social Media to know when we’re building projects or releasing new episodes!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
One of my favorite maker activities is woodworking,
and recently I decided to upgrade my clamps,
specifically adding some parallel clamps.
Today, I'm gonna show you Bessie's K-Body Revo Clamps.
I think they're pretty doggone good,
but I'm gonna let you decide for yourself.
Stay tuned.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
I recently added these clamps to my clamp collection.
I have all sorts of different clamps,
most notably pipe clamps,
and I've got the quick-acting clamps,
but I wanted to make this investment
of these type of parallel clamps.
I looked all over, got all sorts of reviews,
and what seemed to be the best overall features
and quality for the price point was from Bessie.
Now, these are not cheap.
I ordered this set of four clamps from Rockler,
and it came with two 24-inch clamps,
two 40-inch clamps, and four riser blocks
so you could cross clamp across each other
without colliding, and this ran me about $230.
Whew, that's quite an investment,
but it is an investment
if it gives you the benefits you want.
So I'm gonna show you those benefits,
but first of all, let's go ahead and box it
and see what you get right out of the crate.
All right, the packaging, as you might suspect,
is very substantial.
We're gonna go ahead and roll that back,
and inside we have our 24-inch clamps inside their box,
and let's go ahead and roll these around,
and yep, cut the tape.
Let's go ahead and roll those back.
Nicely packed.
Let's go ahead and get those out.
These are our riser blocks,
and you can see the placement diagrams
of how you make use of those.
So when you're clamping 90 degrees from each other,
these allow separation of the clamps
so they don't collide with each other,
but they still grip the work square flat.
So these are a great little accessory
you should not be without.
These are substantial tools.
Okay, we now have this set up to actually do a glue-up.
We'll not glue it up entirely.
I'm just gonna show you as a dry setup here.
A couple observations right off with these clamps.
These type of clamps allow you to simply set them
on a true table surface,
and the clamp is gonna set upright, ready to go to work.
It makes it really easy to load the clamping system also,
and these jaws will stay parallel,
so you're not gonna get this action going.
When you clamp them, it doesn't clamp
as the pressure happens.
They start to spread like this,
causing a rainbow or a bow.
These'll stay straight when they're used
within the specified pressure,
and you're able to develop all the significant pressure
you need to do a nice glue-up.
As long as your stock is true, it's jointed well,
you can close things up very nicely.
Now, notice under here that we rearranged
some of these right here as lifters
to keep these glued pieces of stock off of here
to reduce glue dribble.
Another thing you can do right here
is either masking tape, Saran Wrap,
or lay a piece of craft paper like this along the bottom,
and then glue everything up,
and then pull it out to keep your clamps clean.
But you go ahead and put your items together in here,
square them up.
The handles, when you raise them,
now they're in the adjust mode,
so you can just slide forward, lower it.
There you go, and now these can develop
the needed pressure to really put down some level.
Notice that the leveling here is really nice,
but let's suppose you needed to do
a little bit of leveling up and down.
You can certainly take a wood block, a hammer,
or you can use clamps on the joint line themselves,
but you can see you can develop a really nice piece here.
And then you can also, using an opposing clamp,
so I'm just gonna raise this forward here,
and then bring this down to where it needs to go.
And once you get it down to that,
layer it, and go ahead and clamp it in.
And now you have the opposing side, what you need.
This is a very solid assembly.
A couple of initial observations.
Number one, these clamps are not light.
The longer the clamp, the heavier it is,
the more room it takes, and it's just heavier to handle,
so you don't want tons of these
unless you're gonna do large panels, large glue-ups.
I could see right away that I could see myself
investing in a couple more of these 24s,
maybe a couple 36s, who knows, maybe four,
if I can work the budget out correctly.
And then you need a good clamp hanger system
to put these in here.
As far as what you can expect from brand to brand,
in all fairness, I've had a lot of people ask,
where are these made?
Are they made in the US, are they made offshore?
And it's really hard to get a clear answer.
As far as I can tell, none of these clamps
are made entirely in the United States.
I don't care if they're Irwin, if they're DeWalt's,
if they're Pony Jorgensen, or if they're Bessie.
The box that these came in said,
assembled in the United States from global components.
The riser box over here said, made in PRC,
which is shorthand for People's Republic of China.
So these are all things you have to think about
and say whether or not it's worth it or not.
One of the things I really like about these kind of clamps
is that you don't need to have some kind of bar
that's got slots cut in it to make these stand up.
They sit on a flat table automatically
because of the way both the ends are,
as well as the pads and the stationary end on the clamp,
it'll all stand up and you can just load wood into it
after you've glued everything up, clamp it down,
let it set for the appropriate time, undo it,
and pay and play again.
So it's really, really nice that way.
Now, there's another feature or another accessory
that I decided to buy with this, and these are riser blocks.
And what these riser blocks do,
notice that if you look one way, the slots are deep.
They go all the way to the bottom.
If I go to the side, they're shallow.
See there?
Shallow.
That means if a bar is set in that side,
it's gonna go down deep.
If it's set this way, it's gonna go shallow.
And by setting four of these around,
let's say, a raised panel,
where you're doing a frame and style
or a rail and style type of framework or cabinet door,
you literally can set up two clamps going one direction,
two clamps going 90 degrees to it,
and clamp the whole door up,
and let it set for your 30 minutes
for typical types of PVA glue,
and then move on to the next one.
So these clamp bases are really handy,
and they also have a removable base on them
that allows you to screw them to a table
if you wanted to fix these into a given position
for a clamping station
where you had several assemblies of the same kind.
Let's say several cabinet doors or something like that,
or perhaps cutting boards,
something that is gonna be similar over and over again.
Really handy.
Well, we think this is a really good clamping system,
and it is an investment,
but an investment pays off in the long range.
Another task that you probably do around your shop
is gluing up cabinet boxes or carcasses
for large pieces of furniture.
And when you do that,
you've gotta glue up a lot of corners all at once.
Check out this video where we show you a great product
we found from Rockler that'll help you.
And here's another video
that YouTube thinks you're really gonna love.
Hey, thanks for tuning in today.