Modern Outdoor Chair _ DIY Build

DIY Creators
91 followers
12 Video Views·Dec 11, 2022
Hey what's up guys it's Glenn and today I'm making an outdoor chair using two by fours.
So this is one of those projects that wasn't fully thought out. I just had a sketch on paper
and I just went to work. I used my miter saw to cut all the sides down for the legs
and you can also use a circular saw if you don't have one of those. Now with all the pieces cut
you should have eight pieces for the legs and I ended up with nine pieces for the seat. With some
trial and error I realized if you cut where you want your router blade to stop when you run it
through the router table you would have a less chance of a blowout. Now this notch is only being
cut out for the top and the bottom portion of the arm on the two by fours. I marked the center
point for the location of the screws on both end of the two by four and now I came back with a
countersink bit to pre-drill the holes. Clamp it down and we can tighten it up by installing the
screws. At this point the arms are done for now so it's on to the seat. I placed the two by fours
within the box just to get a general idea where to put the bottom support and to reduce any splits
I pre-drilled the holes and then installed the screws. The way this chair is designed is suspended
by four six inch bolts two at the bottom and two on the back. The bolt for the seats is located
towards the front portion of the bench and I'm marking a center point for the bolts to go through.
The bolt should pass through this arm and into the seats we just drilled
finished off with a nut and a washer. This is all just a test fit so I can figure out
how I want to attach the back. So what I don't know is the proper pitch for a back of a chair
or if there's even one. So what I did was angle the chair down and then attach the back. As shown
in the video I marked the pitch of the arm onto a separate piece of wood. The responsibility of
this piece of wood is to hold the chair back to the chair bottom and now to install the second
set of six inch bolts that's going to be holding the back of the chair up. I pre-drilled and
installed four three inch screws two at the bottom and two at the top. Same thing will be duplicated
on the opposite side. To attach the top to the back of the chair I used biscuit joinery and you
can also use screws I just wanted to keep the top clean. These five pieces of two by four is for the
bottom of the seat which I marked pre-drilled and installed with two inch screws. I use a piece of
scrap wood for accurate spacing between each two by fours and now on to the back which I left for
last because I could not make my mind up how I wanted to join this section together. I was thinking
biscuits but I changed my mind and just went the easier route using screws. While installing the
back I realized I ran out of two by fours and before leaving I decided I'm gonna let the top
dry before I come back and I started thinking and overthinking and then I realized I did not like the
back portion of the arms extended so during the build I had a design change. I made the arms
shorter and I think it was the right move. I got my wood and now I can finish installing the back
before I start the prep work. Since this is an outside chair I'm not going to put too much effort
into sanding this I just want to make sure that there is no splinters in here and I knocked off
any rough edges on the wood. Now to get the stain to take well I applied pre-stained conditioner
before applying the stain. Let it soak in the wood, wipe it off, let the piece dry and then come back
to apply the stain. In the meantime I'm going to paint the legs. After sitting for about 40 minutes
I applied the stain by brush and removed it with a rack. I stained the entire bench from the front
to back and top to the bottom. This chair won't always have the cushion on it so it's important
for me to make sure I get a good coat of stain on it and have it looking as professional as possible.
I gave the stain an entire day to cure and then I came back and I applied two coats of polyurethane.
If the screw heads are a nuisance to you you can add some spackle in the hole,
sand it over and apply another layer of paint to make them go away. To reassemble this chair
it's pretty simple. Install the four bolts, two on each sides and tighten it up. And here's the
finished product of the outdoor chair. This is not meant to be put out in the grass in the weather.
It's more so for your patio or your front porch that you want to just sit back kick back and
relax. Hey want to know what I'm up to? Want to stay up to date with the stuff that I'm building
and see sneak peeks of that? Then you got to follow me on Instagram and Facebook. All that's
down in the description. Appreciate you guys watching this video. Please leave your comments
down below and also give me a thumbs up. This definitely let me know what you guys want to
see on the channel and what I should continue making.
