How to Winterize your RV / Motorhome / Camper water & sewage with RV Antifreeze

C.L.S. All-IN-ONE
129 followers
472 Video Views·Dec 9, 2022
Hey what's up everybody this is CLS all in one. In today's video I'm going to show you how to
winterize the water and sewage systems for RVs such as a motorhome or camper trailer.
Winterization will protect your water and sewage system from freezing if you live in an area with
freezing conditions. So the first step is locating where the water drain is which will usually be
near the water tank. Mine happens to have two drains one for just the cold water and one for
both the water tank and the cold water. So I will just open both of these valves and this will begin
draining the water through a tube that routes to the underneath of my motorhome. Now while the water
is draining I'm going to go ahead and turn on the water pump then open both the hot and cold valve
on any faucet. Now the water may not run very long through the faucet but should continue to run
through the drain underneath. So you should just be able to leave the water pump on until the tank
is empty. Now it's time to locate my water heater and I can access mine from the outside on the
driver's side. So what I need to do here is drain the water from the water heater tank by removing
this plug right here and as you can see it's already been drained. But if it does have any
water inside of it just wait for the water to drain completely then reinsert the plug. And keep in mind
with your water heater you may have a different style of drain. Now it's time to find the water
heater bypass valve if equipped. This water heater holds approximately six gallons of water so if for
some reason I'm not able to bypass the water flow to this water heater I will need an extra six
gallons of RV antifreeze to fill the water supply system. So the bypass for mine is located under the
sink right here. So this valve is currently in the bypass mode which basically cuts off all water flow
to the water heater and allows cold water to run to both hot and cold valves at the faucets. And now
that all the water is drained I can go ahead and close the drainage valves. Now it's time to drain
the sewage system at an approved location and make sure to drain both tanks if equipped. And
once drained go ahead and close all the valves. The next step is to add some RV antifreeze to
the water supply system. Antifreeze such as this can be purchased at most of your hardware and
auto parts stores by the gallon for around three to five dollars. The amount of antifreeze needed
will vary. For my 30 foot motorhome I need around five gallons but for smaller RVs two to three
gallons may be plenty. Now I will pour five gallons of RV antifreeze into the water supply system
through the water fill inlet. And you want to make sure during this step that the drainage
valves are closed so you don't lose any of the RV antifreeze. And depending on the size of your
water fill inlet a funnel may also be required. So here's a look at my water tank after adding
five gallons. And as you can see it's not very full but this should be enough to get the job done.
Now I will turn on the water pump and let it pressurize with all the faucet valves closed.
So it should pressurize here for a couple seconds then shut off on its own. Now I will head to a
and open one of the valves and let any remaining water and air pass through the line until I see
just pink antifreeze. Once it becomes pink I then let it run for an additional five or so seconds
to ensure that the sink drainage is filled with antifreeze as well. Then I just repeat the same
process for the hot water side. Now this kitchen faucet is done so it's time to move on to the
and repeat these same steps again. Let it run until it's pink plus an extra five seconds
then move on to the next valve. So any water related fixture inside your RV will need these
same steps applied including your toilet. And if you happen to have a tub and shower combo
you'll want to make sure to let the antifreeze run through both the hot and cold valves at the tub
So now I have just one more faucet to go and this one is located on the outside of the motorhome
on the driver's side. And this is actually a pretty cool and handy faucet that can be used
for all kinds of stuff. Okay I'm almost done now just one last step. I'm going to go ahead and
open both of my drain valves for just a few seconds to ensure the antifreeze fills the end
lines. Then go ahead and turn off my water pump. And now my water and sewage system for my motorhome
should be safe from the harsh freezing winter weather conditions of Wyoming. And next season
when you're ready to use your RV again when the weather gets nice you will need to drain the
antifreeze then thoroughly flush all the water lines by adding clean water to the tank. Then
running the water until it's clear again at all the faucets. Okay it's now time for me to go.
If you like this video if you could hit that like button and please subscribe.
And have yourself a great day and I'll see you next time.
