Ecowarm Board Radiant Heating Installation Tips

HansonCarlen
46 followers
21 Video Views·Dec 8, 2022
I'm Ryan Hanson with Hanson Carlin Architecture and Construction and we're here today to talk
to you a little bit about the EcoWarm Radiant Floor Heating. So I have a couple of tips that
I'd like to give you as you think about starting to install this on your job. Number one, make
sure that you have the right tools to put all of this in place. So you're going to want a really
good caulk gun, buy the heavy duty construction grade adhesive, and you're going to want to put
a really good bead of caulk around the entire board before you put it on your subfloor. If
you're going to all this work, the last thing you're going to want is squeaks. Number two is
get the right screw gun to put this stuff down. You can see on this floor, we put in somewhere
in the neighborhood of 4,000 screws. It's about a 4,000 square foot house. That's a lot of screws.
So we actually used a gun that's modified from drywall where you can just, as you stand, be
able to attach the screws right into this. It helps save a ton of time and it's also going to
save your knees in the back as you go through this. So make sure that you get the right tools
as you're putting this in. Make sure that you get your subfloor really clean. So you're not going to
want to have anything on the subfloor that would get in the way of your adhesive product. You're
also going to want to make sure that you clean off any of the little bumps that'll create those
squeaks. So number three is, as you're cutting these boards, so they come in 23 and a half inches
by 47 inches long sheets. They're pretty small actually. You're going to want to cut them in a
way where you do it on a table saw every time. We tried doing it with a skill saw and I'll tell you
what, you get just a little bit off and your layout is just going to kill you the rest of the way for
the install. So make sure that you use a table saw. It's a little bit more time consuming, but
then you'll get a nice clean cut and all of these are designed to click together in a way that the
tubing will connect to the next one. If you get that off, now you're using a router or you're
having to modify every single subsequent piece. That is not an afternoon that you want to spend
and it'll kill your productivity. So make sure that you get that right. The other thing is we
snap lines on the wall like this. So you snap a line. I went about half of an inch off, so 24 inches
off the wall. So that way if there's a little bit of variation out of square, we're able to keep a
straight line. And so then as you run your pieces across the floor and you get to a corner like this,
what we found is the best practice is you actually want to come over here and lay out
all of these pieces before putting any glue down. So you have the panels running in, you're going to
cut and lay out these pieces and then you cut the ones in the middle between them to the correct
length. So what that does, you can see an example here, so you have a really small piece. So we laid
this one out at 24 inches off the wall. We had come into this way, so we knew we needed about a
6 inch piece that would go right here. You don't want to get to where you're fighting it against
the end or having to cut these. So if you lay it out beforehand, get everything ready, then you flip
them up, glue them, screw them down, and you're going to get a really nice finished product.
The next thing I want to talk to you about is where you route it into the manifold.
So I use this little Milwaukee router. Might actually suggest something a little heavier
duty. This was quite the workout for this little guy. But you're going to want to take these pieces
of plywood, and before you screw them down, actually work to loose fit them in here. I drew
some lines on here of how I wanted the tubes to go, and then you can see as we've done the tubing
install here, actually just cut the piece off and I'll fill it with a little bit of concrete there,
just self-leveler, to get it into the manifold nice the way that you want it. Okay, so EcoWorm
is actually going to send you AutoCAD drawings that lay out each floor. Now there's a couple of
really important things to know here. I actually like the page that they send you that shows you
the tubing route and the directions that they're going to be sending the flow. What you'll find is
this isn't always 100% accurate, which is okay. I actually, I stopped stressing about these numbers,
and really if you get the cuts right and you're able to follow the routes in a way that makes
sense, it's not too bad. So don't stress if you get to a place where you say, I actually don't
need a two here because this is a little bit different on the actual job site. That's just
fine. You just want to make sure that the tubing is going to run in a way that makes sense. The
other thing that really confused me is they'll send you this list, and this would be feedback
to EcoWorm. The numbers that they send you on how to cut these boards don't actually match the
numbers on the AutoCAD drawing. That was just horrible for me for a while. So all you really
need to understand is the theory of you have two types of boards. You have straights, you'll see
over here, and then you have combos, and you're going to cut the combos horizontally. So half a
23 and a half, 11 and three quarters, or you're going to cut them vertically like this, two pieces
at 23 and a half. Then from there, you can cut them into additional smaller pieces,
and those will make various loops that they show in the AutoCAD drawing. They actually do a really
nice job. That's where the numbers are helpful to say you might want to combo 15. But again, just
know they're calling a 15 a 9 on the plan. I don't know why that is. It's super confusing. So if you
look at it on the plan, you'll kind of be able to figure it out, but don't get too caught up if you
don't know the exact numbers or you have to make changes on the job. The last thing that we want
to talk to you about is plywood filters. So there's going to be a lot of places where you're not
actually going to run heat. Obvious places like underneath cabinets here. The other thing to pay
attention to is if you think about a toilet, you're going to have a wax ring that goes here.
You're not going to want to heat up next to that wax ring, or you're going to have a lot of problems
and be tearing stuff out. So they recommend to offset it back about eight inches. I, you can see,
went quite a bit beyond that just because I didn't want to risk it, and I figured this room is going
to be plenty warm the way that we have it laid out. So that's another example where you can tweak
the plan a little bit as you go. Well, the other thing I would say about the plywood is cut this
and do it as you go. It is very time consuming. It's overall not a super fun task. So each room
that we did, we'd lay out the EcoWarm, and then we would actually go ahead and cut the plywood
and just fill it all in as we go. Helps make the job a lot easier. So if you're considering,
should I or should I not do EcoWarm? I'll tell you what, it's a lot of work. It's not the cheapest
solution out there. Having gone through and done this as our first job, I would say I would
recommend it to customers moving forward who do really want a premium experience. I would say the
service level of their AutoCAD drawings is outstanding. The product itself is phenomenal.
We've had this down on the floor for a couple of weeks now as we've been doing window jams and
other work. It's held up exceptionally well. There's no tears, no holes in the plywood or in
the aluminum cover. So it's an excellent product. Total time that we had in this job, again, about
4,000 square foot house. There's a lot of twists and turns in this home. We're at about 100 hours
for laying down the board itself. An additional probably 35 hours running the tube and hooking
it up to the manifolds. And that doesn't count all of the hours we placed back in the framing stage
into getting the manifolds in the house. So it's very labor intensive. It is an expensive solution,
but it's probably the best solution that you can get for a really nice heating solution for your
home. So I would overall recommend it and think that it beats a lot of the competitors on the market.
