How to Make a Curved Outdoor Garden Bench

Make Build Modify
66 followers
21 Video Views·Dec 8, 2022
Welcome back to Make. Build. Modify. I'm Justin and today we're going to make a curved garden bench.
About 10 years ago I built a cedar deck around a log cabin and around that deck we poured a
decorative concrete patio. And that concrete patio had curves in it and the owners want us to build
benches to match those curves. So I had to cut curves in the planks with the jigsaw
and today I'm going to use similar methods to build this bench. I started by drawing a
1 quarter scale drawing of a 2 by 6. This is an 8 foot 2 by 6 and I'm going to draw a grid on it
so I can draw arcs to represent the curve I'd like to get out of the 2 by 6. The arc is going
to be a 3 inch wide piece of wood and I want it to be fairly consistent and not fall outside of
the 2 by 6. So that's what this exercise was for. Now I know what shape I'm after I can draw it
Masonite is a high density fiberboard and it's really good for making stencils. I'm drawing the
same set of lines or the same grid that I drew in the scale drawing on the masonite. This is to help
me find the arc's location more accurately. I'm drawing all the parallel lines and I'm going to
draw the lines perpendicular to that to establish the sections for each arc. I'm cutting the grid
out of the sheet so I can flip it around while I'm drawing the arcs. It's a lot easier to handle
with it just being a narrow strip. I'm clamping it down to the bench so I can create some
registration lines to draw the arcs. What I'm going to do here is use these little I think
five penny nails to establish a point where the arc starts and ends in a section. An arc is a
circle and in this particular instance it's 58 and a quarter inches for the radius.
So I'm pulling that measurement from each nail and crossing the two lines
and finding the center of what would be that circle. This gives me a common point that should
be able to draw an arc from those original two nails from point to point. This first arc is from
the nail I just set. The second arc is from another nail I set exactly three inches back from that.
So I get a three inch wide board. Now to draw the next section I have to rotate the stencil
and realign it with the registration lines I created when I drew the first arc.
I'm going to swing these two arcs from the same original nails that I placed for the
center of the circle. I did that two more times and now I have the same curve that I had in my
scale drawing. I'm using a bandsaw to cut this stencil out but you could use a jigsaw to do it too.
It's really important to cut up to the line and not beyond the line. There's going to be
inconsistencies in your cut and what I tend to do is come back with a belt sander and kind of smooth
them all out. You can see here I've got a few spots that were not great and it goes right up
to the line after you're done sanding it. I purchased seven 2x6 cedar boards and two 4x4
boards for the legs. I'm choosing the pieces that will be the best for the top of the bench.
Now I'm going through the planks to find the best surface of each plank and I'm going to organize
them in the order in which they're going to be on the bench. Once I found that I'm going to flip
them upside down so I can apply the stencil to the bottom of the planks. I'm applying the stencil
to the bottom of the planks because I'm going to fasten it to them. I'm using screws for a couple
reasons. I want the stencil not to move while I'm tracing it and I'm also going to remove the stencil
to cut the the plank on the bandsaw and then I'm going to place the stencil back using the
to flush cut it at the router table. I also marked an X on the end of the stencil and the planks so
I could orient them again later. When I cut the planks I'm trying to leave a little bit of wood
between the blade and the pencil. That's because I'm going to flush cut with a router and it's
going to do all of the final cutting. If you go past the line you'll leave a divot you can't recover.
I'm reinstalling the stencils and I like to back the screw up until it falls into the original
thread. That way I know the registration hole is lined up perfectly. I'm adjusting this so the
bearing rides on the stencil and the blade cuts right at the top of the plank. I'm removing the
stencil for the last time. I'll save that for another bench and now I'm going to adjust all
of these to where the curves fit together as tightly as possible. The wood kind of warps
when you cut it and you just have to shimmy the wood back and forth until you get those to fit
tight. I'm going to pull them all together with clamps and that way I get the best possible
orientation. Once I get these clamps all together I'm going to flip the wood over and draw some
registration lines so I can bring those planks back to this location when I'm installing them
on the bench. I'm lining the stencil up to one of the planks temporarily to use the parallel lines
as a guide for square for the end of the bench. That way I can cut the end off
square to the original geometry. I like to use round objects to round over corners. It's the
simplest way to mark a corner and find an aesthetic as far as I'm concerned.
Compasses work but you just have to find that center and I usually use a bottle cap or something
round whatever I see that seems like it's going to make a nice corner. I'm using a right angle
grinder with a seven inch disc sander on it. I think it's 60 grit and then I finish up with a
belt sander to smooth out the corner. This is a quarter inch round over and I'm going to use it
on all edges of the plank top and bottom. Western red cedar is a fairly soft wood and sometimes the
bearings and the router bits will leave marks so I'm coming back with a belt sander to clean up
that plus any milling marks the flush cut might have left. I only sanded the outside edges of
the two outer planks on the bench. Those are the only edges that will be visible once the bench is
put together. I also sanded the tops and the corners with 150 grit sandpaper. Now I'm going
to build the leg assemblies. These are the cleats that allow me to fasten the legs to the bench.
They do a couple things. They space the legs out and hide the bolts I use to fasten the legs
and they also allow me to fasten the planks to the legs from the underside so you won't see
any fasteners on the top of the bench. I decided to use a closet rod as a brace for the legs to
keep them from spreading. I'm marking the legs here for the location of the dowel and lined
them up for consistency. I'm using a square to find center. I drilled one inch deep in the legs
and I cut the dowel at seven inches. That way I have a five inch spread between the legs.
I used my plastic dead blow hammer to drive the closet rods into the legs. It's a little bit
harder wood than the cedar legs. Then I used a rubber mallet to drive the second leg onto the
dowel so as not to dent the wood. Now I need to draw some reference lines to accurately locate
the legs on the cleats. I'm centering them up and then I'm going to create a side line so that I
know that they're centered on the cleat. This is going to help me place the legs before I screw
them in. I'm going to use hot glue to tack them in location and that way I can flip the entire
assembly over and not worry about the legs moving. I'm using a forstner bit to drill a countersink
for my lag bolts that are going to be in the center. I'm also pre-drilling so I don't split
the posts. I'm going to use three inch screws on the four corners of these squares I drew.
Then I'm going to use a six inch lag in the center of each leg. I wanted a little bit of
space between each plank and I needed a way to space that out. I decided that bamboo skewers
would be a good tool for that and it worked great. I located the leg assembly about nine inches from
the edge of the bench and I used two two and a half inch screws in each plank. I installed the
middle leg assembly kind of crooked. I used the arc as a guide to determine where I wanted it
but I just used my eye and did what I thought looked nice. Each assembly ends up receiving
10 screws so they're very strong. Because some of this wood had warp in it the end of the bench
didn't align the way I'd like it to so I decided to add cleats to the end to straighten them out.
I used a water-based spar urethane in a rattle can. It seemed to work pretty well. This is a
satin finish and I did about three coats of satin and then I followed up with a semi-gloss
and I sanded right before the last coat. I think it really produces a nice finish.
I like how it's not too shiny and I think it really shows off the natural wood grain very well.
And here's a couple more shots of the bench out in the natural sunlight.
I think it was a very nice project. What do you think? Let me know in the comments. I have the
tools and materials listed in the description for this build and if you think I've earned it please
subscribe.
