Disgusting, she was in need of a new neck for sure! Gotta treat her nice. 203 Thermostat and new Billet Neck for the win!! She will love me long time!!
Guys what is going on and welcome back to the channel. Let me show you what I got for the
7.3. It's a small little mod but I think the 7.3s actually need this mod because Navistar actually
made these 7.3s to run with this but Ford decided to go ahead and change it in back in 96 I believe
and maybe Ford was thinking they're doing it a favor but honestly I don't think so. All right
let's go and see what we got. So some of you guys might remember when I was doing the water pump
my neck the water pump neck not my neck neck but anyways the neck right here was pretty corroded
it was metal it was messed up and I was going to change it eventually and I think and I decided to
go ahead and just get the whole kit and including this new thermostat. Even though I got a new
thermostat already installed from Motocraft I decided to go ahead buy this neck and this
thermostat. I got this kit on Amazon from KB Diesel Performance. I got the link in the
description if you guys want to check it out. Here's the reason why I decided to buy this whole
kit and redo the whole system shebam. Now when Navistar designed the 7.3 they made it so it's
most efficient at around 200 or higher operating temperature. Now Ford changed it and it has a 195
degree temperature thermostat in there right now and that actually maintains about 165 170 degrees
when you're actually normally driving it. So it runs pretty cool which is a good thing and a bad
thing because these engines are meant to run around 200 degrees to be the most efficient.
Now this thermostat which is 203 degrees thermostat was designed for this specific engine
from 99 to 03 7.3s because the older thermostats will not fit because they have a different water
pump system all that stuff. So this was specifically designed for this generation 7.3s. Now
this neck is pretty much identical to the stock one it's just billet aluminum so it's not going
corrode ever. So technically you can buy just the thermostat alone and just put it inside your
factory neck and that will work but in my case because I needed to replace it I decided to go
ahead and buy the whole the whole kit. Now since I bought the whole kit you get two little o-rings
one that comes with the thermostat and one that comes with the billet neck. I don't know which
one I'll use yet they seem to be the same one is a little bit more shiny than the other one
so I don't know we'll see and then plus you get two new three new bolts as well
and yeah so it's a pretty simple install since I've done it before it's gonna be pretty simple
you're gonna have to drain the radiator just a bit so you can remove the upper water hose.
Honestly I don't know if it's gonna improve anything and obviously it's not gonna improve
any performance wise but I'm thinking it's gonna run a little bit more efficient and maybe
it'll improve mpgs just a little bit but a little bit here and there that's what counts right so
let's go ahead and drain the radiator just a bit and remove the water hose and get this guy installed
all right let's go. So it's pretty simple basically we're gonna remove the cover
so we can get to the bolts right there into the clamp and in my case I'm gonna just pop the belt
because it's so easy to do just basically put the wrench in here onto the tensioner
pull it just enough and then we'll slide off and it's not going to be in the way pretty easy
pretty convenient actually makes it a little bit easier to work in this area because the clamp
right here on the hose is going to be a pain in the butt to get to with the belt in the way and
the pliers so I'm just going to go ahead and move the belt out of the way and it's not going to be
in the way to get this out it's going to be pretty easy to do before I remove the hose I'm going to
drain the radiator just enough maybe half a bucket we'll see how good how that goes if it leaks out
on the ground after I'm going to be removing the hose it's not a big deal but I'm just going to
drain maybe half a half a bucket out and while it's draining I'm going to open up this guy and
there we go so it's a baby bucket it's not a full bucket so let's see how it goes
all right that should be enough for now so I got about full baby bucket that's about half a
real size bucket but anyways and that drained pretty much the whole tank right here and I
think it should be good let's see if I can see if there's any fluid no no I just see air so I
I think we're good all right so now I'm going to go ahead remove this clamp right here see what I
mean by the belt will be in the way because even trying to grab it it's kind of a pain in the butt
okay there we go so now we can pop this hose off okay no fluid let's see if I can
no I think we're good but this one's going to be tricky because the neck is corroded so it's going
to be tricky to remove so what I'm probably going to do oh there we go we got it good thing uh
I had this hose off just a few couple months ago or a month ago so yeah it didn't get stuck on
as good even though it's still stuck come on boy let's go there we go all right we're good no fluid
okay I'm probably gonna go ahead and wipe all that stuff inside just from some corrosion there's
still some stuff in there and then I'll clean it up the best I can and I would suggest changing
the hose if your truck is maybe in the salty conditions and has a lot of miles on it
I would change the hose as well but in my case but in my case the truck is from California
with 130 whatever 35 miles right now it's uh it's not that bad probably hasn't seen
snow ever because it was from San Diego oopsies all right so this should probably needs a little
oh look at this see how dirty that is the corrosion and I did the water pump wet
just about a month ago so yeah if you can buy a new one when you do a water pump or thermostat or
anything really honestly or the hoses because you got to drain the radiator anyways
or a better option is buy a billet one because honestly I think you can't go wrong with the
billet necks all right there we go so the thermostat is nice and clean so that's perfect
it's the neck that sucks all right let's clean this up and install a new thermostat with the
new gasket all right so we're gonna put the thermostat in first like so then we're gonna
put the gasket on top here and then the billet neck goes on top of there and we got the bolts
and when we tighten the the bolts that's gonna press the gasket fully compress it
and we drop one again and these bolts are stainless steel so they're not gonna corrode either
all right that's done all right I went ahead and sprayed some WD-40 right here cleaned it up and
then I used a brake cleaner to make sure there's no WD-40 on there because you don't want to have
a slippery greasy surface so let's put this guy on here all right we're good on there
this guy on here make sure it's nice and neutral not bending anywhere all right we're gonna do our
clamp right here you want to put the clamp in pretty much exact identical spot if possible
there's usually some indication where exactly the clamp was for example if you got one line here two
lines here then you know exactly what that's supposed to be so you got two lines in one line
bam now we're gonna pop the belt back on
make sure it goes in all the tensioners and pulleys and not out of whack somewhere
and pull and install okay let's double check everything make sure all the pulleys are
aligned good with the belt that's good that's good that's good we're good good to go
all right let me go ahead and clean my tools up and then we'll refill the tank and then we'll
start up and make sure there's no leaks I had a can that was about a quarter full
so I took the bucket put it in here to make it easier to refill it because I have a feeling if
I was going to use a bucket right here it's going to be all over the place all right that's about
how much was left in the bottle before about one quart that's about how much we put back in
so we're good now obviously I'm going to keep an eye on this after I drive for a bit
and refill it but I think we put exactly what we took out so that's good and we got no leaks
not that I have seen yet so yeah and the only way I will know if there's any leaks is actually
if I drive the truck and it builds up temperature and gets to normal running
temps and then we'll see if there's any any kind of leaks but honestly there shouldn't be any
because we improved everything that we could and new gaskets and everything so that should be all
nice and good all right guys so I hope you enjoyed this video this little upgrade this little mod
I'm not going to do any kind of mpg testing or performance testing sorry got crazy windy
but yeah it's probably not going to be anything noticeable but it's just going to be I think
more reliable and it's just going to run maybe a little bit better and it's probably going to be
a little bit better for the engine in the long run but yeah like I said it's just one of those
things that it's a small upgrade but I think it's a well worth upgrade so if you guys want to
do the thermostat upgrade or whatever I got the link in the description if you guys want to check
that out and if you're gonna if you need to upgrade your water pump neck anyways might as
well do both of them at the same time all right guys so I hope you enjoyed this video thank you
for watching if you're new please subscribe and we'll see you in the next one see ya