Hello, my name's Kramer Ammons and I
like to build bows and I actually like a
tillering stick over a tillering pulley
system. The pulley system is unmatched
when it comes to measuring draw length
at a certain draw weight and exercising
the limbs, but when it comes to actual
tillering, it is way nicer to be able to
draw the bow and look at the limbs
individually and take measurements. If I
could only have one, it would be this.
But this one is not very good. Don't get
me wrong, it works fine. It just doesn't
look good. This was the simplest
possible way to build one. I drilled
screws in with a smooth shaft to put the
bow string on. Made a tea on the bottom
so I could screw it into my workbench.
And then I extended the top over the
screws so that it would draw straight
down. It works just fine, but let's make
a nicer one today. We're going to
improve on this top section by making it
a custom fitting handle to most handles,
but allowing it to be adjustable so that
we can do all types of handles. You see,
a curved handle like this doesn't work
great on a square board like this. Now,
it can fit in place, but it's pretty
finicky. And then when I can put
pressure on it, it'll hold, but it's
only those corners hitting. So, it's
messing up the handle a little bit by
making marks in it. This flat part works
great on a flat self bow like this
because it fits perfectly. So, with a
new one we make, we're going to be able
to adjust that in a second. We're going
to fix that problem on the top and we're
going to use nicer wood to make it look
nicer and put a nice finish on it. If I
take the time to build a really good one
today, then I'll be able to use this
forever. So, I got some scraps laying
around. We got some
hickory. We've got some wing. And we've
got I believe this is a piece of koa
wood from Hawaii. I may also add some
more accents later. This will be the
top. And the first few inches we don't
need any marks. So I'm going to come
down to 8 in as our first spot. The
reason we don't need anything before 6
or 8 in is because when the bow's strung
well, it's already beyond that spot. So
you can start the notches below brace
height. Often people will do every
single inch. I think that's a little
tighter than I need. I'm going to do
probably every inch and a half until I
get down further closer to that 26 in
draw length. And then from 26 to 32,
I'll do every
inch. Instead of adding screws, I'm
going to cut notches in. And I'm going
to do it at 3/4 of an inch in. So, let's
mark our depth now.
Next, I'll take a 45 degree angle, and
that'll allow us to easily insert the uh
bow string
in with the notches cut and cleaned up.
I don't want this to be a straight line.
I kind of want it to be curved like that
because that's how it is when you hold
the bow string. So, I need to sand down
the corners on all of these notches. But
because it's a tight area, rather than
sanding, I'm going to use a rasp and
flip it upside
down. That will allow me to come into it
so I don't chip anything out and get
that nice round look I'm looking for.
This will also make your bow string or
tillering string not cut. Even if
they're serving there, you just don't
want to put it on any sharp
[Music]
corners. It's kind of odd to clean up
the notches here with the curvature and
everything. I'm going to do a little bit
of hand sanding with some sandpaper to
get deep into the cracks and then we'll
move on to the next step. The next step
is going to be putting the top piece on.
Here's what I'm thinking and then we'll
see how much I deviate from this. But
I'm going to put this on here. So, I
will notch out the wenge to let it sit
over top and then put two really long
screws in. Pre-drill it and then I will
curve the top of this wing to the shape
of the most common riser I make.
Different bows have different styles of
handles, but there's a typical kind of
shape for most of them that should fit
on this piece. And then what I'm going
to do is take the inverse of that so
that I can have a flat top as well.
Basically, I'll be able to set on top of
the curved piece another curved piece
that has a flat piece on top. And then I
think I'm going to magnetize it so that
I can drop on the piece to make it flat
and then pop the magnets off and put it
on the side for later use. That way if
I'm using a bow with a flat handle or a
bow with a curved handle, either one
should work just fine. Now I'm going to
try to do that. Will I do that? We'll
see how it ends up working.
Okay. Haven't tried it yet. See if it
fits. Oh, yeah. Awesome.
[Music]
[Applause]
One of the important things is that you
can pull it straight down. If this were
to be mounted back here, then it's not
pulling it straight down. And that
happens on some tillering sticks. So
that's why I moved this forward so that
it would be coming straight down. Now
I'm running into a problem with the one
we're working on right now because I cut
in instead of adding screws. Our second
screw right here in the top is right in
line with where the handle needs to go.
So I may not end up leaving a second
screw there. I'll pull it out. I'll
shape this properly first and then we'll
deal with that problem next.
We want the pressure of the tillering
stick to be right where your palm goes
in the riser when you shoot it. That way
it pulls the same way. And then you want
the pins, bolts, notches to be right
where your fingers are going. So I
actually tailor slightly different for
someone who shoots three under versus
split finger. So for this piece right
here, we basically need to create the
inverse of this.
[Music]
We have the Wangay wood on the top. And
originally I was going to use this koa
wood for the bottom. Um, but I found
another scrap of this Wangay that will
be good for the bottom and that'll keep
with the color continuity. And so let's
do that next. Heat. Heat.
[Music]
[Music]
[Applause]
Uh oh man.
[Music]
Okay. So, let's mark the different draw
lengths. Now, when you measure draw
length, it goes to the back side of the
riser. So, I'll bring that down. Okay.
The first one's at 11, and then we're at
every inch and a half beyond that. I'm
really happy with how this turned out.
It's pretty simple, but here's the
features that you may want to know about
if you want to build your own version.
First, you want it to go as low as any
draw length you would have. I have mine
going down to 33 in. Early on, I have 1
and 1/2 in gaps. Later on, I have 1in
gaps. The reason I did this is because I
don't really need to tiller 1in gaps
early on. It just made it less work of
cutting in the notches. But the notches
I rounded. I wanted them curved so that
when the bow comes on and pulls down,
it's naturally curved with the string.
Now, I wrote the distances from the back
of the handle. So, these distances could
be slightly off if I have a different
thickness of handle. Also, I created the
curvature up here so that the most
common shape that comes in that I build
will fit on here nice and cleanly. But I
discovered something off camera here
that's pretty cool. Originally was going
to build a system that magnetized that
would allow me to put flat pieces on.
But because the deepest part of the
curve is still there, a flat board works
just fine as well. But if you flip that
around and do a reverse, if you do a
flat board, this will not fit. So do a
curved and then flat will fit as well. I
don't know why I didn't think of that
earlier. The base plate is two screws,
so I can screw it into any workbench
anywhere. So, it only takes a second or
two to unscrew it or screw it in and
then I can put it up on the wall and
store it away. The positives of a
tillering stick is that while you're
tillering, it'll stay in place for you.
With the pulley system, you have to hold
it back here. So, if you want to
approach the bow with the pulley system,
it's a lot more difficult. But here, I
could rub a tillering gizmo very easily.
I can continue to exercise the limbs. I
can step around to this side and look at
it. I can take measurements eight inches
down the limb and see how it's bending.
Eight inches down the limb, see how it's
bending. There's a lot of flexibility
you have with a tillering stick that you
don't have with a tillering tree. The
downside is that it makes it a little
harder to exercise the limbs. You have
to pull it like this, but you can also
just grab a bow and pull it like this to
exercise the limbs. The other thing
that's more difficult is testing the
draw weight. Still pull it down and test
the draw weight by looking at the
measurement on your type of scale.
Fishing scale, anything like that works
fine. It's a little more finicky and
it's a lot harder, I guess, than the
pulley system, but because of the
benefits here, it's more versatile. If
you're looking to build one bow or three
bows, weekend projects, taking the time
to build a tillering stick is going to
be well worth it. But if you plan on
making bows long term, I would set up
both systems. It's going to be worth it
long term. Thank you so much for
watching today. Check the description
for links. I'll see you on the next
video. My name's Kramer Ammons. It's a
pleasure that you're here. I don't have
the most followers, the most watchers,
but I've got the best ones. You are
awesome. Catch you soon.