How do you build a slackline spacenet? Detailed instructions on building a bomber highline spacenet

HowNOT2
100 followers
6 Video Views·Dec 6, 2022
Rocco Fucetola, Anthony Cresap, and Kevin Tayah built a 16ft sided spacenet and they share their journey in detail. You can find them at @ark_se
BEST PRICE ON PARACORD is at https://amzn.to/2vauJnR
If you want to create an episode on a subject you are passionate about, message me on facebook https://www.facebook.com/ryan.jenks.35 and we can collaborate.
Find slackliners near you at https://www.hownot2.com/slacklinegroups/
Thank you to my Patreon supporters who donate $1 per episode at https://www.patreon.com/howNOTtoHighline
What are space nets and how do you build them? Check it out on this episode of How Not to Highline.
Space nets are a great opportunity to bring an entire slackline community together
out on the slackline. They're also a great platform for other sports like
face jumping or just hanging out over the water. Space nets are a great project for anyone but
keep in mind you need a lot of slackline knowledge and some equipment to set them up
and use them properly. This is your space net build. We're just going to show you how we build
Who knew you need a lot of space to build your space net? When we started we tried to do it in
my backyard. Trying to build a 16 foot side space net in a very small backyard doesn't work too
well. So I'll advise you to make sure that the logistics of where you're going to set the space
set up and build it are already there. Not where you're going to rig it but where you're actually
going to build the thing. It takes a while. It's a very time intensive process and because of this
you want to make sure that you have a place to set it up for a long duration of time. I built
mine by myself over the course of four days and we built Anthony's over the course of two days.
That whole time we left it up. It was much easier, much more efficient and saved us probably an hour
a day breaking it up and setting it up and breaking it down. Therefore if you're going to
build it and before you go out and get all these materials and have nowhere to go make sure that
you have a spot that you know you're going to build your space net. Be it the park, be it behind
your house, a garage, anything just make sure that you have those logistics in mind before starting
the build project. To build a space net you're going to need a few extra materials besides what
the space net is just actually made out of. To start you're going to need some rope or extra slack
line to hold up the sides. You're probably not going to use your main slack line because it's
going to be up for a while but anything you can use works. You're also going to need a pulley system
or a tensioning system. You could even use a primitive system. You're going to use that to
bring a side to tension when you build it. You're also going to need some attachments to hook up to
the corners. Whether that be soft shackles or carabiners doesn't really matter. Soft shackles
are a great option because it keeps it light and also Ryan has a great video on how to make soft
shackles. Something else that's really really helpful and crucial is fids or a fid set. Fids
are awesome for weaving rope inside of other rope or burying rope and without it it's a huge
pain in the ass. Just get some good fids for whatever size rope you're working with. Something
that also helped us is we made a big plywood circle with nails in it. That way instead of
trying to estimate the size of the hole in the middle we could just wrap it around and find out
how much rope we need for the perimeter. Anything else you might need would be something like tape
measures, tape or markers to help the preliminary planning go a lot easier. To build a space net
and even set one up you're going to need no knots. Now the knots we used we were familiar with,
thought they were easy to inspect and were very strong. These knots involved the girthitch,
the clove hitch, the square knot, fisherman and a modified brummel. To build your space net you're
going to need some materials. You got to consider and properly plan your space net before actually
building it and buying the materials. So we broke it down to three main points. You've got your
outside perimeter which can either be very beefy static rope, very beefy Dyneema or some span sets.
With the span sets which is the traditional option you can opt to either double it back
or if you have a beefy enough span set so to do a pattern like this where you have single
strands. This can only be used if your span set is strong enough. This is what we opted for. Then
you have the second section is the infill or what kind of materials you want to use inside
the span set inside the span set perimeter. You can use either paracord which is very stretchy.
We use 550 paracord or you could use Dyneema which is not stretchy at all. The difference is
with paracord when you bring this space set to tension you're going to be able to lounge about
in it and you're going to be able to sag in it. Whereas with Dyneema you're going to it's going
to be very tight and static because Dyneema is a very static rope and it's not good it could
potentially be not as comfortable as paracord. This is all things to consider on your specific
space net build. Then you also have diverters when you get over 13 foot sides but we will explain
that more later. Once you have all your material you want to make sure you plan properly to be able
to measure it out and cut all your ropes down to size. Now when it comes to measuring you want to
take out your triangle of a span set or rope whatever you chose to do and measure your pick
your corners and measure them out. Then from there you want to actually measure out your static rope.
You want to make sure you're taking account if you have a circle in the middle or if you're just
stringing it across just for extra support and sectioning off those little sections that you're
making with all the triangles. When it comes to the infill space you want to make sure you're
measuring out on the actual span set or static rope whatever you opt to use the distance between
them. You want to make sure you set that up correctly so you have an evenly spaced out
weave between the whole net. We'll get to the actual weave later but make sure you just have
those set up correctly as of now. When it comes to cutting make sure you know what you're doing.
If you don't know what you're doing find someone that can help you. Now you want to plan properly
for it. You want to make sure you cut a little more than you need to leave some breathing room
for your knots and just in general whether you make a mistake or anything. You have all your
materials you've done all your planning so let's get to building this space net. So first we're
going to have to set up through the skeleton phase. So first you're going to set up your span set.
String it up in the triangle configuration that you'd like and that you've marked out
and if it's over 13 feet on the edges then you're going to need a diverter. Now a diverter helps to
equalize the forces throughout the infill and the edges of the space net and also creates another
point for you to clip into while you're on the space net. Diverters can be just simple lines from
the edges or they can be lines from the edges to the middle. The point being though is if you're
going to use diverters you need to measure exactly to the center of the given edge you're working on.
Another option that we decided to take was to add edging. Now edging helps to keep your infill in
place. It keeps the weaves from migrating up or down along the span set and it also provides a
bit more strength and security and simplicity when rigging your net. All right so now we're
going to explain to you exactly what we did. Here is a space net. We had 16 foot sides
on the space net and the corners are anchored with four end soft shackles. Then what we did
is we set up the diverter which is the midpoint so at eight feet from an end. We set up the diverter
static rope to the center. What we did is we tied a circle. I have a three foot diameter circle.
Anthony has a much smaller circle because he didn't want to fit through it. But we tied a
circle. You don't have to. It's completely optional but this is what we did. I'm showing you our design
specs. Then what we did is we strung it with the edging from the Dyneema. We did one continuous
loop. So we started at the side, we went up, over, we actually passed under, around, under, through, under.
Now that went under this way, under, and then under. And then we did the modified brommel knot there.
I would not recommend doing this. I would recommend doing one side, each side continuously on its own.
But I'm showing you our design specs. Then what we did is we did the infill with 550 paracord.
We were able to get 19 different spots segments throughout the side and we doubled it back to make
it 38 different spots each side, not including the diverters. These are 5.25 inches separation.
This is crucial because what essentially you do is since it's on the edging, if you modify the edging
this will shift with it. So make sure that all of them are parallel. We have more on that in later
videos. But essentially it's 5.25 between each one. Now you will also have some on here and
with this and also the ones on the diverter, we had a total of 21 different strands that were
doubled back to make 42 different strands of Dyneema. This makes it certified to roughly 22,000
pounds on each triad. The span set itself is rated for 14,000 pounds span set and the edging
which is Dyneema was 764 Dyneema which is 1,400 pounds MBS. This is crucial. You want to make sure
that your space net is not going to break before the line does. You want to make sure that nothing
within the space net will break and since you're doing this yourself you have to be very cautious
about how you're building it. This is how we did it. This is how we would recommend to do it and
we'll show you how we did it. All right so let's take a look at a close-up of how this was actually
woven. So you begin by alternating from the previous section that you did on termination
with the fisherman's. So you begin five and a quarter inches down with a fisherman's right here
which is then spliced through the rope through the edging through the other edging side and
then girth hitched on this side which then it comes back up midway between the five and a
quarter inch markings and is spliced through. This is when the weaving begins. It goes over
between the first the first one from above and then under and then over again under
over and then you always end opposite how you started so you end with an under. It comes back
up to the halfway goes through the edging and is clove hitched over here which is then tied off
with a stopper knot whether that be a barrel knot or a square knot however you decide to do this.
And with this pattern the edges continue to multiply as you go further down and the bowing
begins to create a circular shape which matches up perfectly with your diverter. First you got to
set up your space net. Now you want to pick a spot where all the sides will be equal. You don't need
to rig it in a spot where all sides are equal but it makes the building process of the space net
much easier. As you can see in my pull bar we made sure that it's essentially an equilateral triangle.
You could have modified this based on how long we want the sides to be but we wanted to be
as even as possible. Now you can see me building the pegboard that Anthony talked about which is
a perfect circle for the inside. This will this helped me get a gauge for what the circle looked
like while stringing the Dyneema through the tridents. This isn't necessary but it was definitely
a useful tool with our first times doing it to have an idea of where everything's going to lay
in the long run. So we're out here rigging the space net at night trying to do the skeleton.
Bad video but I'm going to show you that how we tied the circle in the middle of the space net.
So we got a length of rope. We're doing a three foot diameter circle so we multiplied that by pi.
We used roughly nine feet of rope. We tied a double fisherman's at the end to stop it to make
one continuous loop. Then we're going to rig it up with some more static rope in the middle of
these space nets. We have the pull the space net rigged in my backyard to a pulley system
to two trees. We have Anthony and Kevin working on the interior what I like to call a skeleton
which is our static rope for the rope circle. Looks more like a triangle now but that's because
we don't have all the paracord helping to equalize it. It's looking beautiful. What do you say boys?
So the way we've woven this isn't exactly a science. This whole thing isn't exactly a science
but the way we've woven it is taking the 764th Dyneema and started from a knot and we'll run
this way all the way up the leg all the way down until we get back to one of these knots
and then we'll go through the middle of the of the triple fishermen's to the other side
and then down the back end of this leg and down this stretch and then repeat with the next leg
all the way down to here come back on this side go all the way across and repeat for this triangle
and that's the entire thing. You're live. All right so what we do here is we're setting up
each side of the triangle and set up what we do is we want to make sure that the Dyneema
is a little loose because it's going to bunch up with how many splices. We're doing 42 splices
each side so it's going to tend to bunch up. I've come to learn that this much sag is optimal
maybe a little less and to since we have it continually strung the way we have it working
is that at the end right here to begin doing the lines on each side we splice it straight through
make sure that the cord the paracord is straight we tie it and we tie it through the shackle so
the shackle stays here in this spot with the paracord and along the span set and what we're
going to do is we're going to base all the other lines and splices off of this place you want to
make sure that this place is perfect and you also want to make sure that the Dyneema strands are
running properly. If they're not running properly it might bunch up and it might be very difficult
and mess up the geometry of your circle in the center. Now the way that would happen is if one
of these is way too tight which is connected to an already done segment then it will continue
bunching up and continue to be tighter and tighter which you do not want. You want to make sure
that the Dyneema attached to the already done segment is optimally loose which is what I have
it as here. I have it loose in the center and that's what we have done. Now what we do is we
make sure that the Dyneema is strung so that this is going to be parallel strands all the way down
to the center. We want to move it so that's parallel that's about right and then we're
going to base five and a quarter inches all the way down 19 times. That's what we're going to do
we're going to do it and we're going to get back to you. So we've begun the weave and like we said
we spaced it off of our first knot up here which keeps the Dyneema in place and you can see it's
lining up perfectly. Every five and a half inches we've marked here on the Dyneema with some sharpie
where each splice begins and how you do a splice is that you run it through both ends
on either side and take one end should be I don't know about a foot some love for a knot and the
other ends in order to get the right length cut you pass it once all the way over and get
an arm length and some love on the end and that should be just enough about perfect for when you
start wrapping it around itself like this when it all comes together. So now we're going to run the
first strands of paracord. To run the weave pattern as Anthony already detailed we're going to run a
straight line across first from a fishman's knot to a girth hitch. Now we're doing it all from the
same side here and I would recommend to not do it all from the same side we should alternate but
we didn't know this going into it so ours is going to be a little messed up down the road doesn't
alter the strength any it does alter a little bit of the look towards the diverters that is the only
difference. Okay so we just got done doing the whole segment of stringing it out with a fisherman
on one side and a hitch on the girth hitch on the other. What we're going to do now is we're
going to send the rope that's all hanging on the other side back through we're going to loop it
through each string starting with one end there's going to be one loop here two loops three loops
all the way to 18 loops. The spacing here is about five and a quarter inches in between each segment
to optimize the spacing make sure that it's going to lay evenly and every line is in parallel which
is perfect it looks like that worked. We know the Dyneema is here to keep this all in place so that
it doesn't slide around because this is able to slide around the span sets able to slide around
but the Dyneema keeps it in place. Now what we have is at the end a little bit a little knot right
here with a fisherman's a girth hitch all the way around to another stopper knot which is I tied a
fisherman's again to cinch down the girth hitch so that this will not move at all. This will keep
the Dyneema in place wrapped around the soft shackle the soft shackle stays here this never
comes off the space net and I'm going to check back in once I'm done looping everything. Hello
everyone so we're starting it off with the first five done and I'm going to show you how to weave
it through properly. So as you can tell you start from the girth hitch side you splice it halfway
between so that should be 2.125 inches in between you run it over one strand under over under you
keep running it over the strand closer to the end and then under the strand closest to the circle
and you want to make sure that you hit every single in between and then you're going to end
with an over you're going to end with an under since you start with an over and that under is
going to go straight through we're going to splice it halfway through bada bing we're going to splice
it and it's going to go straight through to a clove hitch. So I'm just going to tie a clove
itch right here that way we can adjust it as we're trying to tension it much easier than a
girth hitch and then we'll tie a stopper knot once it's all to tension. All right we're going to do
the rest of this. Notice how when we're weaving it the weave generally tends to pull the span set
in making it less of a triangle and more of the circular path that we were talking about in the
video. Also how the paracord tends to make a pretty perfect circle as it's getting closer
and closer to diverters as you get closer and closer to the diverters the way the weave pattern
sets is that it forms to a circle towards the inside. Okay so on the first go around of making
a space net on Rocco's what we did and on this trident is what we did is we tied all of the
started on one side and so what that did what we didn't realize is that when you start stringing
it through and pulling tension the way that friction builds up and the tension begins
is that you get these really uneven sides with all this weird bunching and these big gaps
and you get these other sides that have weird bunching and it's it's not very symmetrical you
can kind of notice it once you start working with it for a while just based on the way that
everything tensions from the girth hitches and all. What we did the second time is we alternated
so as you can see every once in a while we have we have a clove hitch, then a fisherman's,
then a clove hitch, then a girth hitch, then a fisherman's, then a clove hitch, then a girth
hitch, then a fisherman's. It keeps alternating because on the other side we have the other
alternating fisherman knots and that way if you look kind of look at this you can see this middle
arc is much more symmetrical this side can be pulled out a little bit but it just kind of
pulls the line in equal directions and kind of mitigates the weird bunching a little bit.
So what happens is when you string the tridents and you do the weave pattern the amseal has a
tendency to bunch up so before threading all the amseal to the center what you want to do is you
want to make sure you go through the whole trident and you pull on the girth hitches
and the clove hitches and the fisherman knots so that the amseal is as tight and aligned as
it can get so that you have all the slack fed into the middle and so that you don't have any
bunching here because if you have bunching here it'll allow it to slide around more and we don't
want that. We want the amseal to thread it properly. Now we're going to have a few bunching
over there because this side of the space net is a couple inches shorter than the other two sides
and to add the 19th strand that we're going to do on each side we need a little extra space
so that was calculated but if you have the space make sure that you elongate it out so that it
works much better. So once you've elongated the amseal I would recommend now to tie the brummel
knots. I would also recommend again to emphasize to do the edging the amseal in trident sections
and not the entire thing. If you did the entire thing like we did we already tied the brummel
knots and we have a bunch of extra amseal in the center because of how the sides start to arc in
with the tensioning of the paracord. So what I would recommend to do is tie the amseal to the
midpoints while you're working on each end and then tie the brummel knot to have the amseal go
together in the middle. Then what I'm doing here over this time lapse is I am running five vertical
lines from the corner and then from the sides of the space net to the middle to more equalize the
circle for me to get a better idea of how the circle is going to look while I run the last
three sets of strands of netting. Then what we're going to do is we're going to run the last three
sets of strands of web netting and I'm also going to show you how we did Anthony's. He opted not to
go for a big circle that you could fit through with a plug. He opted to go for a smaller circle
with everything going with the netting going to that circle. I believe that that looks cleaner
but I also like mine as well because if I set mine up over the water I'll be able to jump out.
If you want to sit up really high you'll be able to hang off do just do fun things with it.
Obviously it's up for your up to your discretion what you want to do what kind of space that you
want to build. What we did here is we have all three triangles done and we did 18 strands each
so we doubled it back that's going to be 36 strands of paracord so far and what I did is
I kept the hole big and I brought it to the hole which I had as a three foot diameter
and did that. Anthony doesn't want to do that he wants to make this all one piece and not put a
cap in like I did. So what we did was instead of shortening the sides to fit the hole we kept the
sides the same page the same length and we shortened the hole. This looks like a triangle
only because it's not strung up yet. Now what happens here is because we did one continuous
loop of Amstel around the entire space net we have this extra Amstel here. I would recommend
doing one continuous strand of Amstel per triangle that's something hindsight is 2024.
Anyway it must you must put all the slack of the Amstel whether it was for one triangle or the
entire space net in the circle itself because we need these to be flush with the sides and because
these connect to each side and then the side of the static rope must be flush and you must not
have extra here that all the extra must be pulled through and left on the circle. Now what we're
going to do is going to string from the sides of the trident into the circle and then we're going
fill in the circle. All right so now everything's done we built the cap on the side for my space net
we're not including that in this video because it's not essential for making the space net
essentially you can do whatever weave pattern you want. I did a star like Captain America's shield
and surrounded it with a blue paracord so the star was made out of Amstel and the blue was
made out paracord which you'll see later. Then what I'm doing now is I'm tying off all the
stopper knots to the clove hitches. Clove hitches can potentially come undone if you don't have a
stopper knot on them. Every clove hitch on the space net has a square knot to stop it off.
The other knots that were used were the fisherman's and the girth hitch and both of those
either ends at a fisherman's or ends at a clove hitch and the clove hitch is stoppered off whereas
the fisherman's does not need to be stopper knotted off. Then what I'm doing is I made nine
small baby shackles baby soft shackles to hold the hole in place so the nine
baby soft shackles can hypothetically hold 3,000 pounds and each so nine of them should be more
than sufficient to hold the cap to the circle. We opted for a weave pattern over the original
random knotted technique since each paracord is strung and weaved across individually.
It will allow for easy replacement of paracord for regular maintenance.
Also this weave pattern has a very uniform look throughout the space net allowing for a nice
finished look as you can see. Most importantly though reducing the amount of knots used will
allow for the strength of the paracord to be better attained and reduces the weight of the
paracord and space net in general. The only visibly alarming part of this weave pattern
would be the rope and rope action happening throughout the net. However this is not a
concern since the paracord will not move enough for it to pose a real danger. It will only stretch
from those points of contact and not slide. And then it's done. All right now that we're done
building our space nets we're going to tell you what we did wrong and things you should look out
for in the future. So one thing that's really disappointing because you lose some square footage
on your space net but it's always happening is bowing. When you start to rig up your space net
to start it looks like a perfect triangle but as you notice when you start working it'll start to
The only way to really mitigate this is to when you start building your space net rig it up under
a pretty good tension. Not so much it would be out in the real world but enough that those sides are
pretty tight so when you start putting in your netting it only pulls in the sides so much.
Also with bowing keep in mind that you're going to start losing a little bit off your diverters
if you're using diverters and you'll need to cut off the extra rope as you tighten those in as the
Another thing that we found was using our weaving pattern we started with all on one side going down
to the other side and then coming back for the whole trident. What we learned is that creates
some large areas of weave that don't need to be there. It's not bad it's not going to make it any
less strong but going doing the fishermen's on the one side and then alternating it every other side
makes for a much more evenly distributed weave pattern and we show we'll show you some footage
on why that is but essentially doing our weave pattern you're best to alternate it.
Now when it comes to measuring make sure you measure correctly. When we were measuring out
our paracord we some of them were measured too short and others were measured incorrectly along
the span set which caused us to have to unsplice all of our paracord and re-tie it in the correct
spot and re-splice which took a lot of extra time very brutal. Our final tip is that if you have a
great idea or original process is that you should film it and reach out to Ryan and How Not to
Highline and share it with the community so we can all grow from it and if you don't you shouldn't
Highline. I just wanted to reach out and say thank you to the community to Ryan Jinks to Andy Lewis
and everybody that's helped us get here. We've been doing slackline for about two years and it was
wholly on the support of our mentors and people who we've learned from to get us to where we are
now. I personally love the community slackline is a big part of my life and I just want to reach
out and say thank you. Watch the video and thank you to the people who helped us get here.
