David Lienbenberg (@jumbosailing) does professional #sailing and shows us how to make an Amsteel loop with a chafe cover. He does three wraps with 1/8" Amsteel and we break it afterwards with surprising results. Eye to eye, 1/8" Amsteel breaks at 12.4kN or 2,787LBF so a triple wrapped loop should be 6x stronger in theory or 74.4kN or 16,725LBF minus some for "nothing works perfect". Because we pulled it "fast", then it broke at 34.1kN or 7,666LBF when it should have been over 44kN or 10,000LBF. So David made another and sent it to me and I pulled it "slowly" and we got 49.95kN or 11,228LBF before I had to reset it because it didn't break, then ironically partially broke at 41kN or 9,216LBF then fully at 36kN or 8,092LBF.
00:00 What is an Amsteel Loop 02:49 Splicing the loop 13:56 Finishing the Chafe cover 19:17 Break Test 25:46 Bonus Break Test
All right, yeah. What is the episode about? What is this called?
So in this episode, we're going to be building a Dyneema loop.
With the chafe material.
Woven in.
Over the top of the load-bearing 12-strand Dyneema.
Okay, I've done continuous loops for highlining, so I'm familiar kind of with that, but I'm new
to the chafe world. But this chafe material, in case you don't know what it is, it's not
12-braided Dyneema. It is Dyneema, but it's like snakeskin. So if you make it bigger on
the inside, then it's, what, not going to hold the load.
Correct.
It's like a sheath, for a rope has a sheath and a core. Very, very, very much like this.
It is literally...
The Dyneema version.
The same thing.
Yeah.
Yes. So we're going to put probably three passes of three mil Dyneema.
Oh, that's why it's so strong.
Inside.
You're literally making an industrial sling.
Yes. And then you can customize it to whatever length you want. You can make it long enough
that you can girth hitch it onto something.
That's going to be strong.
Yes.
Okay. This, we just tested in a video for soft shackles. We pulled straight eye-to-eye
so we could compare it to the actual soft shackle, which proved to be like, what, 21, 22?
Soft shackle is 28 with a button knot.
With a button knot, it was even more. And this is eighth inch, so freedom units. So 3.3 millimeters.
Yeah.
Give or take. Not bad for an American, right? So straight, if straight was 12, a loop would be
20, not quite double. You're going to do three acts. We might have to put the two-to-one on
our hydraulic just to break this, but you build all that inside of the chafe material.
And then cover, and the chafe material sort of gets tucked inside itself and stitched together.
So it's a nice, it's a loop where you can barely even see where the joint is.
Wow. That's so innovative.
So let's see. An industrial sling or a span set is a lot of little fibers wrapped
a lot, probably over a hundred times, if not a thousand. It's a lot.
And I can't even find, where is the seam on this? There it is.
So this is chafe material over, yeah.
Over a loop bearing.
I've actually never seen this, so I'm very excited. So what we're going to start with
is him showing us how to make it. And then afterwards we're going to break it.
Hi, my name is David. I'm a professional sailor. And today we are going to be building a
chafe covered Dyneema loop. Sizing the loop right now. It's going to be about that long.
Just going to cut chafe cover a little bit long. Has a tagline in it that we don't need.
A bent over wire to help pull some Dyneema through the Dyneema chafe cover.
Anything special about that wire?
No.
Okay. Just a wire.
Just a wire. Bend the ends.
So you don't go through.
Yeah, it'll slide off the end if you're not careful.
We have chafe material on some of the soft shackles you can buy for highlines.
Oh, so you go through it.
You don't go to the end.
So that's sort of one pass. You can see the blue gets joined together and it starts to
form the loop. You can use a fit instead of the wire as well.
That's true, yeah. You're pushing it through instead of pulling it through that way.
Yeah, personal preference. So I'm making sure I'm straight coming out in exactly the same spot.
Oh, the same spot.
Exactly the same spot. Otherwise you end up with some unhappiness later.
So now we have sort of two passes.
Right.
And we're going to do one more. You can get thinner Dyneema and do more passes or
fatter Dyneema and fewer passes. Say you need a loop that breaks at 10,000 pounds.
Do a little bit of math and that's one thing I want to learn today is has my math been correct?
So you can size the loop and strength
accordingly based on the number of passes and the diameter of the Dyneema to get your
desired strength.
Do you know what size sheath this is or what it's called?
It's 8 to 10 mil Dyneema chafe cover.
And that's outside diameter that they're basing that on?
It is the outside diameter. So if you were to put a single piece of 6 mil Dyneema inside,
it would be probably around 8 mils outside diameter.
And if you were to put an 8 mil of Dyneema inside the white chafe cover, it would be
9 or 10 mil diameter.
Okay.
And it comes in different sizes. So you can make it a smaller range,
a middle range and a big range often. So, you know, there's 4 to 6 or 4 to 8 mil,
8 to 10 and then a 10 to 14 mil.
And right now we're looking at the 8 to 10 and you're putting eighth inch.
Yeah. 3 passes.
3.3 mil inside of it.
All right. So we have our three passes in. So it'll be three passes.
These guys are going to end up spliced together.
Okay.
Which we will show. And then the white cover will get pulled over all of the blue
and stitched together.
If you have to build it a perfect length, you should be like Sharpie marking to make
sure everything is repeatable and, you know, you measure everything out. But I'm
I'm not doing that today.
Yeah, we're not.
Can you guess how long it's going to be? Like, can you make it precision?
Yeah. It'll take, it takes a few repetitions of building something.
Okay.
And then once you build it, it stretches and sets in a little bit as well. So you have to
know how many wraps you have and displace.
So that's a trial and error thing.
Yeah. It takes some experience.
Okay.
But you can end up building them like really quite precise.
Gotcha.
So we're going to have to taper both of these guys to make sure we have maximum strength.
Ah, so you taper way back.
Oh yeah. So I'm pulling strands out.
So you pull two strands out.
In opposite directions, which helps maintain the braid. If you pull all the strands out
in one direction.
Yeah.
Because twelve.
It'll undo itself.
Twelve strands. Six are going that way. Six are going that way.
Yeah.
So if you pull six out this way, you don't have a braid anymore.
That's how I've always done it.
Oh, so you just pull them all out, then cut.
Yeah. And having a sharp pair of scissors. These is quite nice.
Because Dyneema will dull a knife if you're cutting with a knife.
Even if it is sharp, it will become dull.
And scissors don't become dull.
Scissors. These are special Kevlar cutting scissors.
Oh.
That don't dull. They're serrated on the other side.
They're both serrated. Little tiny serrations.
Wow.
I know what I'm going to be getting next.
And I'm going to do the same distance taper on this guy.
So I'm going to taper both of them.
All right. So I'm going to do a two-step
bury here to help make my life easier.
I've already pre-tapered both sides. I'm going to pull through about two inches.
What are your homemade span sets called again?
Loops. Just Dyneema Loops.
Wow. You'd think these would have a fancier name.
So I'm burying bits that don't have a taper.
I'll be able to show you in one second.
So pull that together.
So that looks sort of like a normal butt splice.
The taper starts here and the rest of it is going to get tapered more.
I'm going to stitch this middle joint together so it doesn't come out.
Then finish tapering or bury and finish tapering both of these from there.
So they're just inside of each other?
They're just inside of each other right there.
And we're going to do a little baseball stitch.
Oh, this is actual whipping twine.
Yep.
Dyneema.
Dyneema on Dyneema on Dyneema.
You got it.
Wow. I thought I was into Dyneema.
Tying a knot at the end of...
This is an overhand.
Just an overhand knot.
Melt the tails of this knot to make sure it doesn't come out.
So it's a loop of Dyneema whipping twine.
Okay.
And it's okay if it just goes through whatever part of it?
Yeah, this is not really structural.
It's just keeping the splice together.
Yeah, it's the finger trapping.
When it's unloaded, it can work itself out.
When it's under load, it all crunches on itself.
And takes the load.
But when you're not using...
When you're not loading the loop, it can wiggle and sort of walk itself out over time.
So this is sort of like Loctite on a fastener.
If that's an applicable metaphor.
Yeah, it's not for the load.
It's for the jiggling.
Finish this by coming out the same hole I went in.
Going under with the needle.
And if I wrap like this, it ends up tying a half hitch around that guy.
And that makes me happy.
I either go straight back down that hole and along the rope and out.
And when you pull, that half hitch you tied gets sucked into the rope.
And now the compression of the blue Dyneema is gonna hold that knot I just tied in place.
Wow.
I'm learning a ton.
Snip that.
Bury the tails.
This is gonna go straight back in.
So I need to, just like I did before,
make sure the wire is coming out in exactly the same spot that this rope is coming out.
Okay.
Because you want it to be completely inside.
So I'm gonna suck that in.
And because I pre-tapered four of the 12 strands, it's easier to do this with the wire.
It's already a smaller diameter.
And then that sucks completely in so you can't see where that was out.
Okay, so it's not brummled or anything.
It's just a pure splice.
It's like a butt splice, I'll call it.
The two ends of the rope sit right up against each other.
So why don't you just go all the way through,
pull it tight, pull the two tails, splice it, and then milk it?
It's easier to, if you have to be very precise with your lengths,
to do this little berry and then you stitch this in place so it can't come apart
while you're doing the rest of the berry and the taper.
You've already nailed your length at that point in time.
Okay, and remember, for anybody who's not familiar with this,
when you put this rope inside of here, it makes this part smaller.
So everything you do to this changes the distance.
If you don't taper, the sudden change in diameter is going to weaken that spot.
But I'm curious.
If you got three wraps, at what point does it not matter anymore?
It's probably super good enough.
I'm wondering.
Of course, do things according to the manufacturer's specifications.
Oh wow, look at you.
That's nailed it.
That's sucked all the way in.
Yeah.
And repeat the process on the other side.
So now the load bearing part is done.
Sort of milk it back around so all three sort of get equalized.
Yeah.
All the same length.
That right there looks strong.
So what do you got there?
We call it millionaire's tape because it's so expensive.
But it's a Teflon tape, like low friction tape.
That is millionaire's tape.
Little bit slippery and pretty good.
So I'm taping that to the cover or the core.
Yeah.
So that I can then milk.
Oh, so that stays on it.
So it just stays in there.
Oh.
And then.
You just use millionaire tape.
Yeah, solves all your problems.
God.
So then we're going to bury this cover into just the other piece of the cover.
In the same way we buried the core.
That sounds hard.
So we're going to taper it and then pull it through with the wire.
I'm excited to see this.
I have no idea how you're going to do that.
Using the point to grab the little strands.
What is that tool called that you're using?
It's also called a FID.
Okay, that's a FID.
Yeah, it's a different type of FID.
There's three or four different types of FIDs.
Okay.
I don't know which type this is actually called.
Okay.
Same thing as before.
I'm pulling in pairs of two opposite directions in the same point on the rope.
Just working my way up.
And this doesn't need to be super tapered for load bearing stuff.
But it leaves sort of an ugly bump in the finished product if you don't taper it.
Okay, so after you unweave it basically.
Yep, cutting.
And I've cut a third of them out progressing towards the end.
Going inside of just the cover.
I'm trying not to hit any of the individual strands inside.
And you can sort of see the wire, the bump right there.
Yeah, I can see how you can be able to tell.
Slide along.
So can you buy these things or does everyone make their own?
You can buy some of these, yeah.
They're, uh, Harken is one company that makes, makes them.
They're not cheap, so if you can.
I just know like after I watch a video like this,
I usually just want to go buy one instead of making my own.
I'm just gonna pull.
Oh, you literally pulled a whole potato through.
Oh, yeah.
Pulling that same through.
And then I have to walk that guy around.
That keeps getting sucked into it.
So then that's what the join.
Gotcha.
Looks like.
And I'm just gonna trim that guy.
Already tapered.
And it's gonna leave, because I didn't taper more,
it's gonna leave just a tiny little bump right there.
But it's not, it's visual only.
And then I'm going to do a baseball stitch all the way around this join.
Okay.
You don't want to stitch through.
Yeah.
Because the three loops are going to move and equalize.
You need them to be free floating.
Exactly.
Okay.
Exactly.
And you said that people can,
they have different chafe covers for color coding?
Or how do they do it?
Well, you can build a white and black Dyneema.
And then there are coatings that can go on top.
So the chafe cover comes in white or black.
And if you get a white one, you can then paint this plasticky coating over the top of it.
That improves UV chafe and helps you identify it.
So you can build them.
You can color code them to the strength.
Or you can color code them to applications to look cool.
Because there's different things you might need them for in different parts of the boat.
Exactly.
So I'm trying to catch both sides of the cover here
without catching the core.
So I'm doing this stitch that looks like that.
And this brown thing is just...
It is a burnt end of the knot.
It's like a stopper knot.
Gosh.
Oh, and you're just going to go all the way around.
All the way around.
And the cover doesn't see any of the load.
Yeah.
So again, this is...
You would have to stretch it back to original length.
Exactly.
So this is just keeping the cover in position.
Yeah.
Super bummer.
I'm excited to break this.
Yeah.
I think it's going to make a loud pop.
All right.
So you got one on the way around.
And how'd you finish it?
So this is the join.
And it's the two covers where they're joined.
It's stitched through one and all the way around the circumference of it.
And then you just stop or do you tie off?
The same way I tied off in the blue dyneema.
I sort of tie a half hitch and bury the tail through it.
That.
How strong do you think that is?
12,000 pounds.
Do you even need it that strong?
It depends.
Sometimes.
I feel like your boat would break first.
Let's go test it.
Okay, we're all set.
We're ready to pull this.
But what was your thought about splicing?
One of the reasons that you have to do multiple passes of smaller dyneema inside
rather than one, say, seven mil loop is the berry has to be a certain length.
And the bigger the diameter, the longer the berry needs to be to have a full strength splice.
So if you were to build one loop out of seven mil dyneema,
it would need to be longer in length than this.
Just to get your splice.
Just to get the two ends tapered together properly to get a maximum strength.
Yeah, but yeah, that makes sense.
Smaller diameter.
You can get small loops like this.
Way less strong than I thought.
I am blown away.
I think we've blown your mind all three episodes.
And this is hot.
Wow.
That looks like it's all melted together.
That's probably why it broke so low is because it it's literally melted to a point.
Is that blue from yours or from my soft shop?
The blue is the the load bearing part inside that melted.
So I think it got so hot that it melted.
Wow.
And that's why it broke lower than expected.
The yeah, time to equalize.
So they were sliding over each other.
Some loads and sailing are like going to be like boom.
But we'll often pre load them and let them sit for,
you know, at 30% of breaking strength for a while.
For a while and they'll settle in.
And they settle in.
Oh, all right.
Math is interesting.
So the soft shackle that we did was what, 21, 22 kilonewtons.
And that's technically four strands.
This is six strands breaking at 34.
So technically, the splices should have retained more strength than that.
We should have been getting 60.
Well, let's pull this part.
I think the splice is still good.
And the dyneema got so hot in the pole that the dyneema melted.
Another consideration is the bend radius.
But that's not a terrible bend radius.
You can see how much it was bending there.
So this is...
Oh, there we go.
This was taped there.
Yeah.
Okay.
So if we pull that tape off.
Can you even take...
Wow.
It's not millionaire tape for nothing.
Can we pull the rest of this off?
I want to see what the load bearing, the blue dyneema looks like in there.
I don't know if we're going to get to it.
What the heck is...
So the three strands of dyneema are there.
And then a little bit of tape left over.
Tape.
There's...
That's not where the splice is.
Okay.
They just got hot and melted off.
I think that's where it was touching the soft shackle.
Yeah.
It's where it went over the bend.
And that is where the splice was.
Yeah.
There's your splice.
It's not the splice.
The splice didn't pull out or break.
It was where it bent at the soft shackle.
Instead of breaking gear for you right now too, I think we're creating gear for you.
It's still pretty strong in my opinion, but I don't know.
Strong enough.
Yeah.
So it's not how many wraps you go around.
It's how you're bent over stuff.
Couldn't think of a better joke.
But we got a whole playlist for sailing stuff that we're starting now.
And we're going to kind of incorporate this into the soft shackle playlist.
And of course, not going to ask you to subscribe because that's annoying.
Thanks for watching.
Cheers.
David mailed me another loop because he had a theory that if you pull slowly and not so quickly,
basically, it would settle and all the strands would be working evenly.
And it would be stronger than what we got on the one and only test we did.
So he made us another one and shipped it to me.
And so I just got done breaking it.
We basically pulled it and it would settle.
So I'd push the button, get it up to about six kilonewtons and then it would just settle.
And a lot of that could just be my hydraulic or the other soft shackles.
But I also think it's this settling.
And then I'm all excited and I go for the gusto and try to break test it.
And I only can go up to 49 kilonewtons before my piston runs out of stroke.
And, uh, or strength, I should say.
And so I had to set up my two to one.
And so, so far we're like way above our first test.
Then I pull it with my two to one and it got 41 kilonewtons
because I rearranged how it was orientated.
I didn't massage it several times in that spot.
And I pulled it at a two to one speed, half the speed as I've been pulling things.
And I got 41 before something broke.
Wasn't quite sure what broke because it was still intact.
Then I pulled it again and I got 36 kilonewtons to get a full destruction of this sling,
which is crazy because one of the three strands in here broke at 41.
And then it took 36 for it to finish coming undone.
Just crazy.
That's, that's really high force for, uh, for what this is.
Uh, and it's kind of crazy how much of a variable we're getting, depending how we use it.
Now, if it's on a boat, like it's going to be loaded in a low enough force
often enough that it should settle to get maximum strength.
I also tested soft shackles for a different video for our Highline segments.
And by pulling slowly and massaging it and like cyclically, slowly, cyclically loading it,
I ended up getting 49, 48 kilonewtons on a soft shackle
that I otherwise was getting 34 kilonewtons on.
It's interesting that Amsteel likes being cyclically loaded,
but now if we girth hitch this, or if you attach it
any other way than just on two big shackles straight,
like we did in the slack set machine, you're going to probably get half.
So make sure you tell us in the comments, what you want to see next, what you think of this,
and check out our other sailing videos in our sailing playlist
and the other videos we got on this channel.
Cheers.