390. Throwing a Roller Texture Lidded/Covered Jar with Hsin-Chuen Lin 林新春 滾花瓷蓋罐拉坯示範

Soul of Siberia
114 followers
7 Video Views·Dec 1, 2022
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/potterysquare
http://www.etsy.com/shop/hsintools
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook page: Hsin-Chuen Lin Ceramics
Today I'm going to make a cover jar with a texture, a rotor texture, this
texture. The rotor and the texture is from MKM. Nice rotor. They got lots of
selection too. To be able to roll the texture deep enough, first I would throw a
cylinder and then I'm going to insert this cardboard inside and then color in
so the clay is fitting nicely and tight so my texture will be very deep, deep
enough. So that's the tool you need. Texture, rotor and then a cardboard. I
already wrapped with two layers of newspaper here and using the slip to
stick together. So that's the cardboard. You might want to have another tool
that to measure the diameter of the cardboard so when you are throwing the
cylinder you don't need to throw very wide or too narrow that you won't be
able to insert. So you can use the caliper to measure approximately the size.
When you throw the cylinder just throw accordingly. Again for throwing a lid
part, you need to have a gallery either on the body or on the lid. So you need to
have a nice 90 degrees of rip or something 90 degrees to push that. Okay
so let's start to throw my first cylinder. This piece of clay is about
maybe three pounds. This porcelain. I'm first centering my clay. You can see
that when I'm centering I'm pushing the clay onto my right hand and my right
hand is kind of a service of a very solid wall. So when I'm pushing the clay
against my right hand, my right hand is brazing the arm right there on the
splash pan so the clay has nowhere to go. While I'm using my right hand
this is what I do. I actually curve my fingers. So I'm not using the center of my
palm to do that. I'm using the tip and the palm pressure. So I curve my fingers and
actually the right fingertip is very powerful. So I use the right
fingertip to move the clay around. So when I'm pushing it and my right
fingertip is moving up and down to get this clay into the center. Okay that's
the centering technique. And then to open it usually I'm using my right thumb to
do the opening. You can use the both thumb but don't recommend you hanging
your hand there without having the support. So put your hand right here on
the surface on the already centered surface and then so brace your arm here
brace your hands here and then use the thumb to drill. So do the initial
drilling using the thumb. Push down and then I kind of widen it. So that's the
initial opening. And now this thumb is only this long and I also don't
recommend you use your thumb all the way down. Unless you are controlling the
wall but it's hard to control the wall that way. So after I initially drill my
hole and actually put my hand here on the side and brace it right here on the
splash pan. And then I move my left hand over here and brace my left hand on the
right so everything the hand is connecting together. And while I'm
drilling it down okay I saw a lot of people try to widen it. You don't
want to do that okay. You want to drill all the way down until you got the right
thickness and then you widen it. If you start to widen it you're gonna end up
with a clay in the center. So drill it down and in the meantime my hand is
compressing, controlling the wall. Keep on going until I get to the right
thickness which is around 3-8, between 3-8 of inch to half of inch. Now I am
taking all the way down and then the fingertips start to widen at the base.
Move the fingertip toward my right hand to make the base wide and flat. You can
compress a couple times to make the base to make the bottom stronger. You can
pull it even wider making a little indentation on the inside. Because a lot
of people tend to not using the clay in the corner so they are wasting a lot of
clay because that corner you have lots of clay there. If you are holding your
finger and making it wider that indentation. So that's the opening
process. Now for the initial lifting. Since my clay isn't that big, if I have a
bigger piece of a clay then I will just hold on here and then use my left hand
to lift. But this piece of clay is not very big and thick so I'm just going to
do my initial lifting by using my left hand and grab the clay and then just
move up. But by doing so the hand is loose without stability. So I'm putting
my right hand there to support it. So this is connecting together. Connecting
together and initial lifting using my left hand. Slowly but steady raise the
wall up. That's my initial lifting. Put the slip back to work especially on the
inside because you don't want to use... I personally don't like to use the water
because the water is not going to stick on the wall. It's going to create a puddle
in the center in the middle of your clay. So using the slip is better. Just
grab the slip from the side of the wheel head and also remove it from your
fingertips and then just coat it before your next move. The lubrication or I call
it slippery is important when you are trying to lift your clay. Slippery. In the
meantime I want to keep my cylinder narrow. The size is fine but I'm going to
put it taller. So by coloring clay in and then squeeze the wall slowly up.
Slippery again before my next move. Outside it's easy. Just touch it up
with a little bit of water. I'm going to lift with my thumb method. So the lifting
is like that. The elbow is tucked into my body and then the thumb is
attaching to the fingertips. My left fingertips point toward my left and
slightly hold it on the wall of the cylinder. Connecting everything
before I do that. Slippery. I can move my clay. Squeeze the clay in first. The
bottom is a bit thicker than the top so I will apply more pressure on the
Slightly lift. I don't want to be too tall either. Still leave a bit of
thickness there because when you stretch it the wall will become thinner.
stretching it out.
Now I'm going to insert the cardboard. This cardboard is already
wrapped with the newspaper. The bottom here is a little bit... you see
there's a lot of wrinkle here. If you put it in you might mess up the bottom so
I'll just soften it by dipping it in the water. Use water to soften it a little bit.
Then just carefully put it inside. Try to put it in the center.
Carefully do that and then I'm trying to color in so the clay is fitting tight on
the cardboard. You don't want to color in on the top first
because when you do that the air is already trapped inside. It's very hard for you
to push it very tight. You want to start from the bottom and slowly gradually
move it up. You want to use the wider... you don't want to have too much
finger around there so using the palm to do that. More of the palm pressure.
Slowly to push that.
There's no rush so you could do that slowly.
Okay so the wall is fitting nice and tight on the cardboard.
Now I'm ready to roll. Before I roll it, there are lots of finger marks there
so I want to remove them. Make the surface clean so the texture will show nicer.
Nicely. I'm using my wooden rib to clean it up.
I don't know if you noticed when I'm using the metal rib I was bending this way.
So using the middle curve so that the bottom of the corner is not
dragging lines. Usually people when they do the bottom they have this corner
that is dragging lines. Kind of move it away. So I don't have the line.
Then I don't want to roll my texture all the way here so I will
probably leave about inch, inch and a half without compressing all the way.
Because if you do that, sometimes the pressure is not even so your room
will be not even and it's super hard for you to try to close it later on.
So I don't usually roll it all the way to the top.
Now bring my roller. Make sure it's rolling freely. It doesn't want to be
stuck in here. Sometimes this is not quite rolling freely and you're stuck.
It's gonna be very hard to pull it out. So make sure it's rolling freely.
If not you can use a sandpaper to just grind. So this part, the middle part will be shorter.
So it will move more freely. And then to prevent the clay from sticking on here.
Because once you roll the clay tends to stick. So my suggestion is you dip it in water.
Dip it in water and then you want to hold the cardboard. Hold it to support it.
And then you roll from the bottom. You roll it up and I would do this angle
about maybe 45 degrees. And then when you pull up, you can feel that the pressure is more evenly.
If you do that, sometimes you are pushing it too hard.
So the texture is not evenly go up. Some part is lighter, some part is too deep.
So let's hold your handle here about 45 degrees.
Okay.
So you rolled about maybe halfway, maybe two-thirds. You have to calculate how many more
you can do. So that you will be able to distribute your texture more evenly in one full circle.
So here maybe four more times. So I can calculate like half here, half of that.
So four more times. So then the distance will be a bit smaller for each one.
Okay. So you can see that I evenly distribute so that the texture is evenly go around the whole circle.
Okay. So that's putting the texture on the cylinder with the cardboard inside to support it.
Now after that, I'm going to just lift and remove.
The surface is a little bit too dry, not smooth surface. So sometimes the friction, so it's hard to pull it out.
And also if you choose the cardboard, make sure that you have both ends that it's going through.
Because if you have one side sealed, when you try to pull out, it's going to suck the air.
Okay. So it's like a syringe. Okay. So make sure that it's open. And like I told you that I have two layers of paper.
So I'm going to lift the inner paper first. It should be very easy to pull out.
And then finding the inside part of that, and then slowly pull it out from there. And then kind of roll it.
Roll it. Okay. Beautiful. That paper is not sticking on the wall.
You have to do it quick though, so the paper doesn't get too wet and then stick onto the wall.
Right now, so I'm ready to stretch it. But since the paper is absorbing all the water and the slip,
so the wall is kind of dry. So I want to put a little bit of water on the inside of the wall.
Make sure my hand is clean.
And wet without dry clay on it.
A little bit of water inside on the wall.
Okay. So initially, you might want to use the sponge to stretch it.
So I'm using the sponge inside. Hold it there and stretch it.
But later on, I will just use my hand, my fingers, because I feel the contact of the finger, I have more feeling of it.
But initial shaping, I could use the sponge to do that.
And since I already have a texture, so I won't be able to touch the outside.
So basically, it's just the fingers inside and the sponge inside to make the shape.
So I'm going to compress this part first.
So I'm taking my time to blow up the volume. And my eyesight is usually looking at the curve here.
See which curve I need to push out. My eyesight is not here. It's looking further to see the profile of the shape.
Slightly close the top.
So the base is fine now. And I'm going to stretch more from this point.
Widen a little bit so the foam is not so slim. Kind of a little bit fatter, a little bit fatter.
Maybe a tiny little bit more here.
So that's how I carefully grow the foam, taking my time to do that.
So that foam, the profile is fine now. The foam is nicely done. And then taking care of that top.
Putting my fingers inside to support it while I'm compressing the shoulder.
So before I push my gallery, I'm going to put the gallery here.
The rim is not even, so I will cut it even.
Okay, and now I'm going to use
the ordered rib to press the gallery here. So to do that,
90 degrees, I'm holding my rib this way. Okay, so the 90 degrees will be on here and then push it
down. But while I'm pushing it down, you need to have a support while you're pushing it down.
Put my finger there and connect everything together so that it brings in all my fingers and my arms.
So
I have the rim here. Using
the chamois to smooth it. People ask me what is this, the blue thing.
This is what we call chamois oil. People use that for washing the car.
It's also called absorber. If you go to Amazon or Walmart, they have it. Something to absorb
water. It's called absorber. They come with a large sheet of this material. And then
I use a scissor to cut a small piece. This is working very good for smoothing the rim.
Making the rim smooth. So that's the body of the
cover jar. I'm going to make some line here.
So I'm going to draw some uneven line and then just cut exactly off the foot.
So that's the body. Actually, I forgot to put a bed here. Now it's hard for me to lift. I could
lift the whole piece but I will probably mess up the texture. So I will need to have some
heat gun or hair dryer to dry it so that I could remove it.
And then I will show you how to make the lid.
For making the lid, you can make a simple lid but usually I like to put the gallery on both
the body and the lid. So for that, it's a little bit more complicated because
you need to measure the inner part of that and then the outer part of it. So you have to measure
twice to be able to fit your lid in nicely. So I will show you how to do that later on.
So I'm using this small piece of clay to make the lid for the body.
I already measured the inner part of the diameter of the body and then I will do that. And then
later on, I will measure the outer part because I have a gallery on the body.
And I like to also put a gallery on my lid too. So if you have a gallery on both the body and the
lid, it's a little bit complicated to make your lid. But usually you could do on either one of it,
not for both of them. So for making the lid, you want to open up a shallow dish
with the outer part a bit thicker, this part here, because you are going to
make your gallery right here. So put the finger there to hold it and then
the right index finger too. You can squeeze it a little bit. So it's almost the shape of
the gallery. Making sure that the width is okay. It's too wide now. So I'm going to move it in.
And also use my thumb to push a nicer curve. There's a curve here that is nice and fitting
on the inner part of the lid. Still a bit wide, so remove the clay a bit inside.
And again, I use that 90 degrees on the rib to push it and put the finger behind it
when you are pushing. I guess this is still a little bit wide, so I'm going to push.
Okay, so it's about right.
Do the final compressing.
So right now, taking care of that outer part. First, I will throw it out and make it thinner
before I cut it to the right size.
Then I measure the outer part of the gallery on the body. Okay, a bit wider now.
I'll use my number 10, a very pointy knife to cut.
I'm using the wooden knife to trim. You can trim it later, but I prefer to trim it
when it's wet so I can save the clay.
So the inner part of the lid is about here. So from here to
the wheel head, I still have about, I would say about at least three quarters of an inch.
So I could use that to trim the nut. Okay, so that's the lid. I'll cut it up and
trim it later. Okay, I will show you how I trim it.
