Economical and Sturdy Hose Hanger & Yard Hydrant Combo!

DirtFarmerJay
310 followers
2 Video Views·Nov 30, 2018
When form, function and economics come together, it's a beautiful thing! That's what you'll find in this combination yard hydrant (faucet) and hose hanger that is constructed of economical and readily available supplies from your local hardware store or big box retailer.
The design uses a steel tee post, 3/4" galvanized pipe, faucet head, hose hanger, band clamps, and basic PVC plumbing parts to give a durable and attractive result!
You can build one of these in half an hour and have a great addition to your yardscape for years to come.
Hey, this is Dirt Farmer Jay from DirtFarmerJay.com. If you have a yard scape of any size,
you need water handy all over your yard. Well, we've come up with a great way to do a combination
hose hanger and yard hydrant using commonly found materials at any big box store.
Stay tuned and we'll show you how. All right, let's get to work building your own yard faucet
and hose hanger combination. The great thing about this approach is that the materials are readily
available at any hardware store, big box or local, small town, and the price point is very,
very reasonable. So let's look and see what you need. The first thing you're going to need is
a T-post. I prefer to use a six foot T-post so that you get enough depth in the ground because
you're going to support a lot of hose. I put up to a hundred foot of hose at a time on these.
So you want it in depth down far enough that it'll hold a big loop of hose and it'll keep the faucet
up at a height that's handy to you. The next thing you need is a piece of three quarter inch galvanized
pipe. This happens to be 60 inches or five foot long. The next thing you need is a fitting. Here's
it's three quarter by three quarter, this elbow, but this side right here is threaded. This side
is slip. You'll need that to put on the end of the pipe. The next thing you need is a short piece
of PVC pipe that'll connect this to a slip by slip tee that's threaded here.
And the purpose of this is you need a drain, this little fixture right here that screws in,
and that's going to allow when pressure is taken off of this at the end of the season for this to
drain out, therefore getting water out of the pipe so you don't end up with a split when freezing
weather hits. Then of course you need the faucet itself, and I like this style because it puts the
hose approximately 90 degrees off to the side and reduces the amount of pressure, sideways pressure
on the hose, and reduces fatigue on the hose itself. Next thing you're going to need is a
couple of these kind of band clamps. You can get these in different sizes. These are a little large
for this project, but we'll trim off the tails. If you've got something that fits a little bit
better, that'll be fine as well. And then of course you need a little bit of glue to assemble
your parts. You'll also need some pipe thread sealant, also known as pipe dope by many people,
to make sure you don't develop leaks in the joints that you thread together. And then lastly you need
the hose hanger itself that's going to mount to the T-post. These are fairly inexpensive. They're
only probably seven to eleven dollars, and so this works very well. It's reinforced, but you have to
do a little modification to the T-post to make this work. All right, let's assemble this. We'll
begin by assembling the plastic components. Make sure to assemble this opposite this side because
this drain needs to go down in the ground while the pipe up to your faucet goes straight up into
the air. Be sure to apply pipe dope both to this connection and when you put the piece of galvanized
pipe into this end of the fitting. Now that we have this portion assembled, let's take it
and our pipe over the vise and assemble it. Okay, let's go ahead and get this portion affixed to
our metal pipe. Of course you want to apply some pipe compound. Make sure that those threads are
filled nicely. Now that you have adequate pipe dope on the metal threads here, it's time to
put this fitting on. Now be careful though because this fitting is soft and of course this is a lot
harder and you can end up inadvertently cross threading this. So take care to make sure you're
threading this on properly. Well let's go ahead and go around slowly till we make sure it's threading
and there we go. I can see that we're straight and we're using hand pressure can go ahead and take
this around until it really starts to cinch down. And then I don't try to over tighten because you
split the thread here, but go ahead and just take a couple turns using like a water pump
plier or something like that. There we go. All right, let's turn our attention to the other end
and put the faucet head on itself. Okay, we've already flipped our pipe around in the other end.
Our plastic fitting is down on the other end and we're going to go ahead and put the faucet head
on. As you can see, we've already put pipe compound on. Let's go ahead and thread this on.
Again, just take care because brass is a little soft and get that threading on correctly. All
right, it's got a nice shoulder here where you can put a wrench on it and let's go ahead and tighten
that head up. All right, now we've got this assembly done. Now it's time to move on to the
hose hanger portion. As you can see, this hose hanger has these two mounting holes here. The
cool thing, it actually lines up perfectly with the nubs that are on the T-post, but there's one
problem. The tail down here collides and you can see the next nub actually stops us from setting
down properly. We're going to go ahead and grind that off real quick. Well, let's see how this
looks. Hey, not bad at all. That lays down flat. This size down here is laying down flat. When we
install this, we'll use one of those clamps, actually two of them, to clamp this on and to tie
the galvanized pipe to the post. Before we move on the next step, let's go ahead and touch this up
with a little bit of paint to protect it from rust. All right, let's go ahead and put it together out
in the yard. All right, we've now installed our yard hydrant with the metal pipe down in our
underground plumbing and we need to now drive the T-post beside it and then we're going to go ahead
and mount our hose hanger. So to get started, let's go ahead and orient this in such a way that
the nubs are facing this way where the hose hanger is going to be. Notice that I've oriented the
direction of the outlet on the faucet so as the hose spills off it, it's already going in the
direction that the hose hanger is going to be set. That reduces stress here and keeps a kink out of
your hose. All right, let's go ahead and drive this post down and make sure that you put the bottom of
the post in such a way that it does not damage the plumbing in the ground. Notice how that nests in
there very nicely. So we're going to go ahead and affix our hose hanger here, put band clamps around
this and tie it all together. Let's see how this baby works. Here we go. All right, let's tighten on
a hose here. You can see the tails down here. You can clean that up by clipping them off and burnishing
the ends. But let's go ahead and coil the hose up here. All right, that's 50 foot of hose, but you can
put up to 100 foot on this and it'll work great. As you can see, this really, really works well. It's
economical, easy to make. Hey, if you found this video to be helpful, why don't you like it and
subscribe to our channel and also check out these other great tips that we have for you. Until the
next time, this is Dirt Farmer Jay from DirtFarmerJay.com.
