Highlining - Making Whoopie Slings

HowNOT2
100 followers
3 Video Views·Oct 11, 2016
Step by step instructions on how to make whoopie slings so you can add redundancy to your highline anchor. Samson Ropes instructions are at http://www.samsonrope.com/Documents/Splice%20Instructions/12Strand_C2_Whoopie_Sling_AmSteel_AmSteel-Blue_WEB.pdf
This is for entertainment only. Please don't trying highlining without an expert!
Support these projects through our new coffee company https://www.brewjuno.com
Highline University, Bolting Bible, Book of Slack... all the good stuff is at https://www.hownottohighline.com/
What are whoopee slings? How do you make them and how do you use them?
Check it out on this episode of how not to highlight.
I'm Ryan Jinks and welcome to my kitchen. Today we're going to show you how to make whoopees.
Disclaimer this is for entertainment purposes only. Don't go making whoopees that your life
is going to depend on after watching a guy in his kitchen show you how to do it.
Today I'm going to make a whoopee out of quarter inch or six millimeter
Amsteel 78. This whoopee will break at about 30 kilonewtons or almost 7,000 pounds. I use 12 and
a half feet of Amsteel to make my whoopees and they come out to a minimum of 20 inches long
all the way out if you stretch it to the tail to almost six feet long.
There are three parts to a whoopee. The bromo splice, the loop, and the end of the tail.
Let's start with our bromo splice. It starts with the tail and a loop. This quarter inch
sum of it has a specific length to help you know how long to splice certain things. Our loop is
going to be one fid long. It's five and a quarter inches and two fids long for our tail. So I'm
going to mark where I want to splice my tail and my loop. So I'm going to take my tail. I'm going
to put it through my second line until my first line gets to it and creates an eye. So now I take
my fit and go through the exact middle of the Amsteel. Be sure to have six strands on both sides
or your eye is not going to be full strength. Then take the tail and slip it in the back end
which has a little hook that holds it in place. Massage it through and now you have your eye.
Pull the first line and the second line together. Now the bromo locking splice needs to be spliced
twice before you bury the tail. You go about two diameters down and you're going to put the tail
through this tail. Now that I've run my long tail inside of the short tail, now I just cinch it up
and my eye cannot open. Now we're going to bury this tail down the center. You poke it through
but not all the way through. Stay in the center. Scrunch it up and before the end goes in there
you put the tail on there. There's a little hook that it gets stuck on. Make sure you massage it
on there well so it doesn't fall off. I find turning it will help it go down more. Then you
milk it over it. Stay in the middle. Milk it over it. Stay in the middle and you continue all the
way down until it's buried. Once it's buried you come out the end. Pull out your tail and then it's
ready to taper. In order to taper I'm going to go back about an inch or two and I'm going to unravel
the tails and I'm going to cut them progressively up the rope so it'll taper nicely.
Now that I've cut progressively up the rope I can milk starting at the top. Milk it all the way down
the rope so now I have a locked brommel splice that won't open, a buried tail, and a tapered end.
Now to create our loop we're going to put our Amsteel inside of itself two fids and come out
of the Amsteel before it hits our taper. So I'm going to measure two fids from where I feel the
end of my taper and that is where I'm going to enter my tail. I'm going to insert my fit at that
mark and go down the center of the Amsteel putting my other tail on my fid before inserting.
Stay in the center. Twist. Push. Milk over it and be sure to come out
before you hit the taper that you put in earlier and pull the tail all the way through
creating your whoopie. Now that we have our brommel splice and our loop all we have to do now is create
a stop on the end of this so it can't accidentally become undone when you're working with your whoopie
slings. What we do is we bury the end inside of itself like we're creating an eye yet we pull it
all the way through. So you push. Push it all the way down the center here. Milk it over it.
Milk it. Now the trick is to keep going. Go all the way to the end to where it creates no eye.
Come out the end and pull out your tail. Now because this isn't going to hold any weight
I'm just going to cut my end at an angle instead of doing a real taper. Pull off the extra tape
and I'm going to milk it but not so much that I get an eye and now we have a stopper.
If you want to see Samson's instructions for making a whoopie sling I've included the link
in the description below. So now you know how to make whoopies. They're a great tool to add
redundancy to your highline anchor but since there has not been thorough testing
with whoopie slings in actual highline scenarios therefore you shouldn't highline.
Hi I'm Ryan Jinks and this was another episode of the how not to highline series. It's a guide
for slackers interested in transitioning into highline. We are not here to spoon feed the right
rigging techniques. Instead we are here to empower slackers to critically analyze any system they're
using. Risk awareness can keep people alive. Please don't rig your first highline without an
expert. We have too many generous and wonderful people in our highlining community to go risk
your life after watching a YouTube tutorial. Let's keep this sport safe and remember since
no system is perfect therefore you shouldn't highline. Thanks for watching and please subscribe.
