Buy your DFJ T-Shirt, Cap, or Coffee Mug at https.//www.dirtfarmerjay.com/shop
If you live in your house for over 15 years or have bought a home that is over fifteen years old and still has the original bathroom ventilation fans, the time is coming when you’ll need to service or replace the bathroom vent fan.
When I was on home construction crews, these fans were called “stink fans” (or the less genteel “fart fans”). The reason is pretty obvious, but an incomplete description of the important work this fan accomplishes. Not only does it whisk away undesirable (that’s an understatement!) odors, but this device also removes moist air that occurs with showering and bathing, as well as steam coming from the sink when hot water is used. Unabated steam leads to condensation on the room’s surfaces, which can lead to in-wall moisture that can easily encourage mold and mildew. Not good.
As an aside, when running, the ventilation fan can also create “negative pressure” in a smaller bathroom, assuring that both humidity and offensive odors are not forced into the adjacent living areas.
If you think that lubricating the motor bearings is all that is in order, here’s a video from another “YouTuber” that can help you do that.
However, there will come a time when the unit has to be replaced. If the unit is 25 years or older, the housing may no longer be a standard size and both the housing and the fan will need to be replaced. Replacing an older fan is not the subject of this video. This is a more complex process many times simply because the parts in older units weren’t designed to be modular, allowing you to “swap out” components like newer models do.
Because of this, taking out a very old bath fan and putting in a new one is an extensive process, requiring access from the attic in most cases. If the old fan wasn’t properly vented to the outside of the home (not just into the attic - a real “no-no”), then that needs to be installed as well.
These units are rated in CFM (cubic foot per minute). The basic minimum ratio is that you need one CFM per square foot of floor space. The dimensions of our demonstration restroom are 5’ x 9’ = 45 sq. ft. So, a 45 CFM fan would be the minimum. The contractor installed a 50 cfm unit, so they were in specification.
If you need to remove the old housing and place a new setup, the new unit will have instructions and diagrams to accomplish this. As an example, here is a link to the installation guide for NuTone®’s 80 CFM HB80RL ventilation fan with integrated light.
However, in THIS episode, we will feature the NuTone® 696N Ventilation Fan. This is one of the most common bath fans and has been in use for many years. This allows you to leave the housing, vent outlet, and electrical connection all intact, and simply “swap out” the motor/fan module - literally in minutes.
The basic steps are:
Remove the cover to the ventilator fan unit and set aside. Unplug the fan motor from the plug. Locate the mounting tabs of the motor/fan assembly. Locate the inscribed directions in the unit telling you where to lift the component and where to push the housing side out to allow the motor/fan assembly to swing down from one side. Remove the motor/fan assembly from the housing by swinging out the unit and having the component tabs release from the housing. Clean the inside of the housing, and assure the damper is working properly on the duct outlet. If servicing and not replacing the motor/fan assembly, then clean the unit, and lubricate the bearings with light oil. Don’t use WD-40® as it possesses only mild lubricating properties. Re-install the fan/motor assembly, plug it in, and replace the cover. If you are replacing the motor/fan assembly, take the assembly to your favorite home/hardware store and find a match for your unit. They tend to be standardized. Our replacement unit came from Home Depot®: https://www.homedepot.com/p/Broan-NuTone-50-CFM-Replacement-Motor-Wheel-C350BN/202191734, and cost about $17. install the new assembly utilizing the mounting tabs. Assure that the tabs are securely attached! Plug the new unit into the outlet, and clean and replace the cover using the spring mounting clips.
To do this, you’ll need only basic tools and the skills you’ll learn from DirtFarmerJay as he demonstrates how to easily accomplish this home maintenance project. And, you didn’t need to hire someone to do it. You know you can JUST DO IT YOURSELF.
Hey, Dirk Farmer Jay here from DirkFarmerJay.com.
If you've lived in the house you're in right now
for 15 years or you bought an older house
that you know is older than 15 years old,
sooner or later, you're going to either have to service
or replace your bathroom fan.
The good news, it's not that difficult.
Stay tuned and I'll show you why.
Hey, Dirk Farmer Jay here from DirkFarmerJay.com.
Sooner or later, you're gonna need to service
your bathroom ventilation fan.
Well, in this brief video,
I'm gonna walk you through the purposes of a fan,
how to service the fan if it's just lubrication it needs,
and even if it does give up the ghost,
what it takes to replace the modules in these.
Lastly, I'm also gonna show you in case you have
an older fan that parts are no longer available
and you need to actually take out the fan
and replace it, some resources to do that.
And as is our habit, we always give you more resources
in the description below,
including a couple of ordering links for these products
as well as instruction sheets and what I'll tell you later
when you're putting a whole replacement in.
And so check those out down there
and that'll help you to review anything
that I cover in this video we have together.
Well, number one, what's the purpose of the fan?
Well, you know, everybody may think like
when we were on the construction sites,
they always called these stink fans
or the less genteel fart fan,
but that is only one of the purposes
and that is to remove, shall we say, unpleasant odors.
Just as importantly, and probably more importantly,
the idea behind this fan is to remove humidity
from the restroom when hot water is running the shower,
the bath or the sink.
Why is that important?
Well, you may see humidity or condensation
form on the surface and usually that wicks away
pretty quickly when the door's left open
or window's left open,
but what's really especially insidious
is when moisture gets behind the wall
into the framing members and the insulation
and you get all sorts of bad things happen
like mold that can really cause problems, dry rot.
So the real important reason is to remove humidity.
Now, how about sizing these fans?
They come in different ratings called CFM,
cubic feet per minute ratings,
how much air they remove out the vent
on the other side of this fan unit.
And the rule of thumb is that you need one CFM
for each square foot of bathroom space minimum.
And this little bathroom we're in right here,
this is five foot that way to behind me
and nine foot behind you over to the other wall.
So five times nine is 45 square foot.
This fan is rated at 50 CFM.
So it makes it, but it probably would have been better
to have something larger.
So exactly why are we replacing or servicing this fan?
Well, this house is 20 years old
and it's serviced a long time,
but take a listen and you'll see why.
That may not sound that loud,
but when you're in this little bathroom,
it drives you crazy.
So the first thing you need to do to repair one of these
or to replace the motor module
is you're gonna take off the grill.
And what you'll do is just tug on the grill.
And when you do, it comes down,
it's held by these spring clips.
You just squeeze the clip, it drops down, see there.
And there's another one that's going up
into this housing right here.
So let's go ahead and pull that, we'll get rid of that.
All right, now that we've got that open,
the next thing we need to do is unplug
the motor unit right here.
So we're just gonna reach here, unplug it.
And now this modular plate with the motor
and the blower can come out.
So there's inscriptions right here on the main housing,
right here, and there's one up in here
telling you what to do next.
What you're gonna do here is it's gonna tell you
push right up, up this way.
And when you do, push out on the housing over here.
And what you're doing is letting that tab
out of the little capture that it's in.
When you pull this down, it pivots.
There's two more up here, lift it out out of those,
and the whole unit comes out.
And as you can see, it's collected a fair amount
of dust over the years.
So if we were just servicing this motor,
we'd go ahead and vacuum this off.
And as you can look up in here, the first order of business,
let's go ahead and vacuum that all out and clean it out.
All right, now we've vacuumed that out.
You can see the circular housing here,
and right over here is the duct exit.
So you need to make sure that that's not obstructed,
that the flapper works well,
that stops air flowing back in,
and so that's all ready to go.
Now we're ready to either service the module
and put it back in or put a whole new one in.
All right, we're going to simply put in
a whole new one of these.
This is the existing old one.
But if you did want to service this
and oil the bearings here, this little simple motor,
we're not going to provide you that in this video,
but go to the description below
and check out the link there
where another YouTube creator has done exactly that for you
in case you want to just keep this and service that.
But now we're going to go ahead and get rid of this
and unbox a new one.
All right, we were able to buy
this replacement ventilation fan.
We actually bought the whole thing,
the housing that you see up here in the ceiling
that protrudes up into the attic, the grill,
and the whole module for about $17
at the Orange Big Box Home Improvement Store.
But you can get them for a couple of dollars more.
I just wanted to show you.
This is New Tone 696N.
This model has been around for probably 25, 30 years,
and this is a standard housing up there,
which then means you don't have to do a bunch of tear out.
You're just going to replace.
So we're going to go ahead and open this
and see what the new piece looks like.
All right, so let's slide that out of there.
And as you can see, there's a whole new module here.
This housing's already up there,
and we're simply going to do the opposite of what they did.
We'll go ahead and pop this out of here.
Okay, so let's go ahead and put this motor plate
with the components in.
You saw that it only took a few moments
to get the other one out.
We vacuumed this out,
made sure the vent outlet is working well.
Now we're simply going to reverse the process.
These two tabs go into the two slots
that are over here out of sight to you,
but I can see them here.
And then on this side is the main tab
that that single tab goes into.
And if you notice, there is a hole right there.
If you were unsure that it was going to stay in there,
you could drive a sheet metal screw in there to secure it,
but it's been up there this whole time
for over 20 years with no problems.
Now this may fight me a little bit.
Let's go ahead and put this in
just to get that tab in securely.
We're going to put this up in the housing.
Sure enough, it fits fine.
That side is in the slots on its side.
There we go.
We're going to push this up on that side.
And as you can see, it wants to resist a little bit.
So what I'm going to do is just use a screwdriver right here,
put that up, push it to that place,
and then push the tab in.
And when I did, notice the tab is inside.
I'm going to yank on this to make sure it can't come out.
And there you are.
Now we're going to plug in our outlet right here,
and let's go ahead and test it.
Well, there you go.
All right, let's go ahead and take the grate.
You're just going to squeeze together the tab
on the end there, insert that into the slot.
It holds on.
Do the same thing closer on this side.
I have to get around in front of you a bit to do that.
And once it's hanging like that,
you simply push up, clip, and the job is done.
All right, let's suppose this won't work for you.
You tear into this.
You find out that the unit is an older unit.
You can't get parts for it.
It was improperly put in place.
Perhaps you've got dry rot and you need to repair.
Well, at that point, you need attic access,
and you're going to need a new fan unit.
Now, that would be a fan unit, something like this.
This is one that was also at our Orange Big Box store,
a New Tone 80 CFM.
This has an integrated light.
You can actually get Bluetooth speakers
and all sorts of things, different grill configurations.
But that's the pretty side on the downside down here.
What you're going to have to do is get into the attic
and actually do some work there to support the unit.
And what comes in these units
are complete instruction sheets
that show you new construction, old construction, all that.
In the description below,
I've provided you a link to this actual PDF download
that you can take a look to see what you're getting into.
Another thing you may want to know
if you're doing a lot of your own home repairs
and it has to do with electrical work,
there are two or three testers you should not be without.
You can check out the video at the top there
that tell you about some testers
that we looked at recently
and that we depend on around here.
Check that out.
In the bottom video, YouTube has gotten into your mind
and is presenting a video that it thinks is perfect for you.
Check it out.
Until the next time, this is Dirt Farmer Jay
from DirtFarmerJay.com.