Converting A Retro Mountain Bike To Single Speed - 1990 Carrera Katmandu
9 Video Views·Nov 16, 2022
Today I'm going to use the Katmandu for another video and convert it to single speed.
It's not quite as simple as a let's say an old road frame with horizontal dropouts,
you can't just bang a single speed cassette on there and pull the wheel backwards into the
dropouts to tension the chain. You've actually got to use a chain tensioner on these because
they've got horizontal dropouts as have vertical dropouts, much as modern road bikes.
So today I'm going to do that, it's going to involve removing all the drivetrain,
I'm going to change the crankset as well because this one I can't
take off the chainrings. So yeah let's get cracking.
Clearly once everything is off you can go ahead and put the brake levers back on
and put the grips back on and I've actually gone ahead and changed the bars on this
while I was at it because well the old ones were really narrow and they were slightly
uncomfortable for such a big bike. So yeah put the grips back on and then we'll get to
the conversion parts. Okay so first thing I'm going to put on is a chain tensioner.
With these dropouts on the bike there's no real room to tension the chain, same with
if they were longer actually on this bike it might be possible because they're
on the horizontal plane. If they're on the vertical plane as well there's no chance you can
tension the chain properly. So there's a couple of options available, well actually more than a
couple. There are ones that you can get for bolted axles which basically look like they just have a
hole, an arm and another arm and then they just bolt to the axle itself either on the
inside or the outside, probably best on the outside. Or you can get ones for the derailleur
like this which is this one. This is made by Mr Control apparently, it was about 15 pounds off
eBay and when it goes on it should keep the chain tensioned. So when it's on properly
the chain goes round and it will pull it down and keep it tensioned round. Without that you're not
going to have enough tension, the chain's going to slop around. So I'm going to fit this. This one
has a little pin on the back there which is for the tension so that just has to go on this little
nook here. So you do have to start it in the wrong position, that'll go on and then swing round
into place and that will tension your chain for you. And someone's come to visit, where you going?
Okay so next thing I'm going to tackle is the cassettes. Obviously with normal, I say normal
they're old now, with the screw on type three wheels you could potentially just screw your
old one off and screw your new one on. You might have to play around with adjusting the axle
length, axle spacing and dishing of the wheel, maybe. But with a cassette it's a bit different.
Yeah that's all right, that's nice and loose. Tall chain whip, badda bing badda boom.
And then I have this little kit here. There are so many of these kits on eBay.
They're just a standard cassette kit, cassette conversion kit. It's a single speed. They'll come
in, all this packs them up, they'll come in 1 8 inch size, they'll come in a normal I guess 5 32 inch
size, different speeds to use on your chain, different prices, different materials. There's
so many that you can get but this one was a dirt cheap one from the UK, so yeah you could probably
get them even cheaper from China. It's just anodized aluminium, it's an 18 tooth, it comes
with all these different spacers so you can adjust the chain line. I doubt I'm going to need all these
spacers because they will just sit over there. Yeah and your sprocket goes on, stick another
spacer on, another spacer and then you put your lock ring on and Bob's your mother's brother.
But before I actually do this, I should have thought in ahead, I need to actually find out
the chain line. In fact while I'm here, chain line. Chain line is obviously going to be measured from
the centre of your bike, so you're going to have to do a bit of maths. You're going to have to work
out where the centre point on this hob is. So you've got your over lock nut diameter from the outside
of this lock nut to the outside of the other lock nut. Half of that is obviously going to be
bang in the middle, but then you're going to want to know the dimension from the bang in the middle
to this cog. So just take the dimension from this lock nut here to there, take that away from
your half dimension and you've got your chain line. Simple on a single speed, absolutely simple.
So for the front, what I said I'm going to do is put on a new crankset and that is exactly what I'm
going to do. You can obviously use your crankset that has removable rings, it shouldn't be a
problem. You could even strip all your rings off that crankset and put a 1 8th inch chain ring on
there as long as it matches the bolt circle diameter of that crankset. It shouldn't be too
hard. For me, I didn't have that option, so I've gone for a new chainset and I just picked this
up on eBay cheap, it's a used one. It's actually off a Victoria Pendleton bike, so it should be
1 8th of an inch because they tend to be single speeds and if that goes on there, that's actually
sitting not too bad, not too bad. I could bring it in a little bit and the way I can do that is
to change the axle length. The removable rings on here and on similar cranksets can be undone
using these bolts and you can add a spacer if you've got enough length on the bolt behind the
ring or even shift this ring to the opposite side to bring that in a little bit. But with
this crankset that I'm using, I can go ahead and put a smaller axle in there to bring the chain
line in. If I bolt this up now, I will be able to see what my chain line is and match that up
to the rear. So I've got that crankset in place now, it's just bolted on this one side just so
I can measure the chain line and what I need to do is measure from the centre of this tube
to the centre of this ring. So we're going to want to go around there to there and my chain
line is actually about 50mm on this, it's pretty much bang on 50mm. So I can check that against
the rear to see if I need to make any adjustments. Okay back to the rear, so front chain line is 50mm
at the moment, rear chain line is 135mm for the LRD divided by two which is 67.5mm.
Let's take away roughly like 23-24mm which gives me a chain line on the rear of about 44mm.
So I actually need to bring that out a little bit which is where the spacers come in.
So I do that up so tight with my fingers that I can't undo it now. So I need to sort of add
6mm is that? Yeah I need to add about 6mm behind this spacer to actually bring it
better in line. So if I measure, if I get my, how thick are these rings? Each one of these rings is
3mm. So let's add those on the back. So now 67.5 minus 10, 11, 12. Yeah that should be perfect. 67.5
minus 17 is 50. So that should give me a pretty much perfect chain line which is really helpful
with keeping everything straight. So this can go back on the bike now and then we'll fit the chain
and adjust the tensioner. Hopefully the light won't change again but this is the last job to
do now on this simple conversion, fitting the chain. I've gone with a 1.8 inch chain, it's KMC
and yeah it should be this pretty much standard single speed style. You can get 5.32s as well
but right first thing I need to do is check this.
Right this chain tensioner has a slight fit of adjustment on it here which I need my Allen
So you can just adjust this little, what would you call this? Spindle? Axle? I'm not sure what
you'd call it. It's quite tight. Why is it so tight? But you can adjust it so it sits directly
underneath the, oh that's tight, there we go. So it's directly in line with the sprocket.
So normally what you would do on a single speed is if it's got these horizontal dropouts,
the long ones, find your point where the chain is going to connect which actually on this one
is in links so that would actually be pretty good. There'd be a bit of slack in the chain
but the inner plate here matches the outer plate here which seems pretty much perfect for this bike
but with the chain tensioner I could actually have it this whole length that I've got here
and the amount of sag in that would be taken up by the chain tensioner as I can probably demonstrate
so feed it through chain tensioner comes around connect that together and there we go
that chain tensioner has taken up all the tension in that chain and you could actually ride it like
that. I think I might take out a link or two just to make it a bit neater, put the chain on
and then it's ready to ride with a little clicky. Where's that clicking coming from?
So if you watch the tensioner it's not quite meshing with the chain so I need to double check
that but boom that is a single speed conversion let's say 99.5% done. Nice single speed easy
conversion done. So what did that cost me? Let me just bring that up. I bought all these parts
for not too much. I mean the chain tensioner which I actually need to check the pulley
compatibility because it doesn't say in the listing I just assumed it was one eighth inch
that chain tensioner cost me £15.54 delivered. The single speed cassette conversion kit the
little red one that you see cost me a whole £10.95 delivered. The chain is only like a £4 chain
so that's all you would need unless you decided to buy the crankset as well which I managed to
get that crankset for £12. So yeah not too bad at all. It's a nice little conversion that you can
do if you just want to cruise around on a retro mountain bike. It really is as simple as stripping
off all that gearing so taking off the shifters the derailleurs. I took off the crankset and then
putting all this stuff on and as long as you work out the chain line properly it should be a nice
simple conversion and I hope I explained those chain lines properly. But there we go that's the
Carrera Katmandu now as a single speed with the chain tensioner and everything working nicely as
long as you enjoy that tick of the chain tensioner. So I hope you like this little video of this
single speed conversion. Plenty more where this comes from if you want to check the rest of the
channel out. I've got myself a nice whiteboard now so I can keep on top of all these projects
that I've got to do. So keep watching, subscribe for more and I'll see you in the next video.

