1989 Marin Palisades Resto-Mod - Vintage Mountain Bike Restoration & Upgrade
10 Video Views·Nov 16, 2022
Welcome back. This one is a bit of a mess. It's a 1989 Marin or Marin Palisades
and it needs a lot of work. It's nasty. It's covered in dirt from being stored in
sort of a barn slash garage. The spokes on the front are completely rusted so the wheels have
to be rebuilt. Actually the spokes on the rear are just as bad. Obviously it's got that comfort
saddle on it. It's not very nice. The shifters have been replaced at some point with some Altus
C10s. The original brake levers have actually had the original shifters cut off them for some
reason because it should be running the mountain LX groupset all round. The rear derailleur has
actually been nice. It's been replaced by a Shimano Duo XT and it's still running the original
crankset, front derailleur, pedals and brakes. In fact the wheels are original as well. It's
got the original mountain LX hubs on. Now the plan with this is going to be a bit of a retro
marb. Is that what you call it? I'm going to strip it back, hopefully get the spray cans out
and tidy it all up. Get it running a 1x10 I reckon just so it looks nice and clean,
nice and tidy. Things I'm going to need. I think maybe a nice saddle although I might have one in
the drawer. I'm tempted to actually change the brakes to V-brakes so I'll get a new set there.
Well not a new set, I'll get a used set. That crankset should still be useful to me. I'll be
able to swap out the rings and put a 1x ring on there, narrow wide. Front derailleur, obviously
can get rid of. Rear derailleur, I'll put a sort of modern Shimano or SRAM on there as well as a
matching shifter. And the wheelset, well I think I've got a spare wheelset knocking about that I
and it'll be a nice, it's got good geometry. It'll be a nice old steel 1x10 cruiser if you want,
commuter if you want, adventure bike. It's going to take a while to get this all back
to its former glory. The rust on there I think I should be able to just sand back, treat and then
spray. Obviously I don't usually spray the bikes. I have done in the past but I always like a nice
baked on finish and spraying at home doesn't give that toughened, braked on finish. But I'm going
to give it a go because people have asked. Oh that's tight. Oh well, nice. If you chose caged
you were right. And yes I have bought the proper tool for this now and it does make it so much
easier. Bets on this being loose? Let's see. Oh I've got so lucky. Straight in the bin. Okay so the
seat post was free, the stem's free, oh the pedal's free. Yes. But before I just take this off let's
just see with this actual length what the chain line is. I've got about four, what do you call that as?
So the middle ring because this is a triple, let's call it a 48mm or 47mm.
Yeah so when I change the rings around, stick a narrow wide in place of the middle, I'll have a
47mm chain line. However if I move it around to the outside and shorten the axle, buddy
this is really nasty. So that's stripped and this is obviously the worst area around the bottom
bracket I guess where all the mud has built up and I've just left it there. It's probably where you
should clean your bikes. So I intend to actually get this sandblasted just to check what's under
there and it will be a hell of a lot easier for me. Saves all the sanding. So yeah we'll see what
happens then. So I hope you've seen that video where I've gone through everything about spraying
this bike with sprayed up bike paint but here it is and I'm more than happy with the design I've
and how it looks. I'm a little bit unhappy with the quality of the finish of the recommended finish
so next time I do this I'll definitely be adding a bit more to it but yeah it looks awesome.
If you haven't seen that video go and check it out but I'm going to continue with the build and
go through all that. I think this flex stem will be better but I do need to change the
horizontal part. Now with the bottom bracket I've actually downsized it slightly.
Originally it was a 122.5 and if I'm moving the chain ring in because I'm using the original
crankset so I want to put it on the outer. I want to sort of put the middle ring on the outer if
that makes sense. I've got to move it in 5mm so 5mm per side 10mm I'm using a 113mm bottom bracket.
So bringing that bottom bracket in and using this HUP chain ring which fits on perfectly.
It's narrow wide 34 tooth and 38 tooth sorry 110 BCD and let's put the British flag out.
Now I want to hide that there and I'm going to use some of these narrow wide not narrow wide
oil slick bolts for a bit of bling and that should give me the right chain line.
Torvey hey Torvey come here you little monster yeah not bad. Now would you look at that it's
done it's there glistening in all this winter light and I've got to say I really enjoyed
this project really did enjoy it turning this old rusty 1989 or 1990 I think it's 89
marine palisades and just giving it a bit of a resto mod a restoration and a modification.
It's gone from the 3x7 21 speed with the cantilever brakes to this more modern 1x10
with v-brakes so it should work a bit more efficiently maybe all round it's definitely
a lot cleaner now there's no more rust on the frame it was all shot blasted off
and I've got the girving flex stem on there as well which I was gonna convert it to a
threadless headset not headset threadless adapter for the stem but it just didn't look right so
the girving looks great on there especially as the fluoro pink but yeah I'm just super stoked
with how this has come out hopefully I get to use some more of this sprayed up bike they seem to be
interested in you know how this paint job has come out and yeah I definitely although it isn't
the best finish on this particular bike because I only use limited cans I do want to do it again
especially on the scott team racing that I've got and restore that with some sprayed up bike
not modify it like this one just restore it and see what effects I can get but yeah I really like
this I'm actually thinking of my original plan was to sell it but I think I might keep it
and either switch over the maguras from my scott and sell that or refurbish you know those old
maguras that I've got and then put them on this and then keep them both we'll see what the future
holds but yeah I really love this color scheme really do so yeah I hope you've enjoyed this
build if you haven't seen the sprayed up bike separate video I would go and check that out
that's doing quite well at the moment and if you've used sprayed up bike and got some honest
feedback as well leave it on there but yeah all my feedback is mainly on that video from the paints
parts on this were great if you do need any I will try and link as many as I can in the
links in the description they're all amazon links but I get a little kick back so that helps me
Toby's just jumped on the wall and yeah subscribe if you want to see more hit the like button
share it around because the shares really help and I'll see you in the next video thanks for watching

