3 Japanese Saw Tricks You Should Know.

House Love
61 followers
6 Video Views·Nov 12, 2022
3 Japanese Saw Tricks You Should Know.
Today I want to show you my three favorite Japanese handsaw tricks.
As some of you may know, I am brand ambassador for Suizan saws.
And what comes as a really cool perk for that is I can now offer my favorite
Suizan saws in the Katzmoses store at a discounted rate for you.
And in fact, they are on presale now.
There's a link in the pinned comment and the description.
Now, as all of you have seen, I use my Suizan folding Dozuti and
folding Ryoba for just about everything.
And I wanted to show you some tricks with these.
That seem really intuitive, but really help kind of the minutia of woodworking
and solve some of the problems you may have in your day to day handsaw work.
So let's come to the bench and let me show you number one.
Now, number one is a depth guide, and I'm going to show you how this works
with a really cool acrylic see-through guide.
So you'll actually be able to see me sawing, but you can see at
the tip of each one of these saws.
This is the small Dozuti, and these are all the ones that are in my store.
The small Ryoba, the small flush cut saw that does both hard and soft wood.
The folding Dozuti and the folding Ryoba, they all have this final tooth
here at the end that is very big and is used as a depth guide.
Now let me show you how that works.
Okay.
So when you look at the end of a Japanese saw, all of them have this flat part
here, and the end of that tooth is exactly even with the length of the first
cutting tooth in your saw like this in this direction, and then of course,
the teeth are in a straight line.
So when you tip that up, that becomes a depth guide.
And let me show you.
So when you're cutting wood, you tend to cut down to your line
here and down to your line here.
Let's say that our line is right there.
That's our depth line.
And we end up cutting like this.
And then with these depth guide here, when you tilt the saw up and it rests
on this tooth, which is a non-cutting tooth, you can then use it to just go
right along your line and it's going to trim out the fibers in the middle
and leave you perfectly at your depth.
So let's look at that here.
We'll do a real close up here through some acrylic and you can
see it actually in action.
So when you're cutting and you can see our depth line there, when you're
cutting, what you have a tendency to do, especially with dovetails, is you
cut down to the front of your line.
And I'm exaggerating this a little bit.
And then you will look over your board and you'll cut down to your depth line
there, and you can see that there's a hump in the middle.
And here I'll change the acrylic here so that we get a nice clear look at this.
Actually, fun fact, these were a dovetail jig prototype.
We were trying to figure out what material to make them out of.
So you can see perfectly that is very typical of a dovetail cut because you're
so worried about the back of your line and the front of your line here that a
lot of times you leave a hump in the middle and then you have to clear it
out later with a chisel.
But here is just the easiest way in the world to do this.
So when you take the front of your saw, normally you would be cutting like this.
You're going to tilt it up so that it's perfectly sitting flat on that there.
And then what'll happen when you start to cut away at that bump, this little tip of
your saw is going to catch at the lowest part of your line and keep you from going
any further.
You can see that it just perfectly takes it down to that line.
All right, let's talk about number two.
Trick number two is how to saw squarely.
And I have a whole video on how to saw correctly, but this is just a trick you
have to know so it bears repeating.
And I'll link that video right here in the corner.
But when you're rip cutting and on a Ryoba saw, these are for cross cutting,
these smaller teeth to sever the fibers of the board.
And these are for rip cutting because it's much easier because you're going with
the grain.
And here's a little tip within a tip, which is start with your cross cut side
just to get the line going and then switch over to your rip teeth.
Tends to work a lot better.
But the real trick here is to look at the saw's reflection.
So when you look at your board in the saw, you can see that when I move my saw,
the reflection of the board starts to move.
And so you want that board to look like the full board in the reflection.
So you don't want those lines to be crooked.
So I check the reflection of my saw and make sure that the board is in a straight
line when I'm cutting.
So I'll start it with my cross cut teeth here and then flip over to my rip side.
And then I'm just going to watch the reflection of the board.
And look, you can see when I angle too far this way, the reflection changes as
well.
So you want it to just look like a real board without any distortion up or down
or left or right.
And that's how you know you're cutting perfectly square.
And then once it gets down a little bit, you're not going to have a problem
because it's going to stay square.
If you look at that cut without even trying that hard, we've got a square cut.
All right, let's talk about number three.
All right.
Trick number three is kind of the opposite of trick number one, and it's about
using the first tooth on the saw.
So we have our knife line and you've watched my how to saw correctly video.
So we're going to make a little knife wall, but that knife wall is going to be a
little bit angled and a little bit difficult to get your saw to sit this way
correctly.
So you can use this last tooth the same way we did the other one and just drag it
across and it's going to clean out any of the chisel waste that you couldn't
remove with your chisel and it's going to create a perfect knife wall.
And so that way, when you start cutting, and of course it's on both sides of the
saw, so it's just real easy to just clean out the waste, sort of like making your
marking gauge line just a little bit deeper, but it squares up that little
crevasse there.
Crevasse.
I'm so fancy.
And then you can just start getting a perfectly straight cut.
When you start angling your saw, just like that.
So that's trick number three, guys.
Remember to go down and check out that pre-sale.
I have five saws, the two folding Ryoba and Dozuki, which the Dozuki is the one
for dovetails.
And then I also have the smaller versions of those same two saws, which are very
economical.
The flush cut saw, which does hard and soft wood, they just released.
This is very, very good.
And if you pair that with some of my other products, like a dovetail jig or a
stop block, there's going to be massive discounts.
So go check out that pre-sale down below.
They're all going to ship out next week before Thanksgiving.
So thanks for watching guys.
Stay safe in the shop and have a wonderful day.
