CORRECTION! I state in this video, "sharpen only on the flat side of the cutter - NOT CORRECT. I said the opposite of what I meant to say - you sharpen on the angled side of the cutter. Sharpening in the flat side will lead to a short life of the cutters. My Mistake!
Any maturing or long-term yardscapes is going to have sizable shrubs and trees to maintain. That means having the tools to prune and trim them, including “Lopping Shears”, also called “loppers.”
Loppers are typically designed and rated to cut green branches up to 2” in diameter. They are able to accomplish this, even when the user is only of moderate strength, by creating high leverage due to the length of the handles, and the very small area where cutting force is generated.
All this mechanical advantage comes at a price; the handles need to be swung apart fairly wide to make a cut, and then pulled or pushed together. When working in a shrub or tree that is quite congested with growth, you’ll need to strategize the best way to approach the cut so that you can move the handles together. As further cuts are made, space will open up and this will be less of an issue.
Loppers come in two basic types; bypass and anvil. Bypass are scissor-like, with the sharpened blade moving past the roughly perpendicular edge of a stationary hooked piece. This piece serves both to somewhat grasp the branch as it is being cut, as well as giving an edge for the sharpened blade to shear material against. An anvil lopper works by landing a sharpened edge against a flat surface; the anvil.
These types of pruners also come with a simple single fulcrum point, or assisted with gears and sometimes ratchets. The cutting head assembly can be made from stamped steel or cast. Most consumer level models are stamped.
After damaging our lopping shear, we needed to replace it and ended up buying the Fiskars® PowerGear®2 Lopping shear. It’s a good homeowner level shear, with a price point under $40, good serviceability, and moderate weight and reach. For the amount we use it, we think it’s a good buy and most users of the tools that use it from time to time will be pleased. Even so, professionals probably would be better served to buy commercial grade tools.
Do you have a favorite lopper that you use? Do you have some insights to offer? If so, won’t you share your knowledge by commenting below? THANKS!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. If you have even a moderate size landscape,
you're going to end up doing a lot of pruning. And as that landscape matures, those branches are
going to get bigger and bigger. And sooner or later, you're going to have to invest in a lopping
shear. Well, we're going to review the Fiskars Power Gear 2. What about the price for this?
The value you get? Is it serviceable? Will it last? Stay tuned and we'll let you know if this
is the right lopper for you. Hey, Dirt Farmer Jay here from DirtFarmerJay.com. Thanks for joining
us today. In this episode today, we're going to review the Fiskars Power Gear 2 Lopping Shear.
Now, this is the product card that came with the lopping shear when we bought it. And as you can
see, it makes some claims on there, such as three times more cutting power. It talks about titanium.
And then down here, it says for cutting up to two inches of branches. Well, that is true. All of
those items are accurate. But we need to tell you what that means. When you look down at one of
these types of lopping shears, you can see that this is a compound type of lopping shear. There
is a gear. And when you open this, there is a double fulcrum that forms here. And there's a lot
of leverage that is applied through the handle system to the cutting area right here. And when
they say that it cuts three times more, what they're saying is three times more powerful than
a non-compound type. So if you have a single bolt type of lopping shear, you won't have the same
amount of leverage applied when you operate the handles. And it takes a lot more muscle power
to get a cut through a branch, especially something that's drier or large diameter.
All this cutting power comes at a price, though. To get all of that force concentrated right here
in the cutting area on the bottom hook and the bypass cutter right here, you have to move the
handles a wide distance. So to get this to open to two inches of cutting, I've got to have those
handles all the way out, almost 180 degrees. Now, that means, as you can see, when you go to
cut up in trees, you have to kind of figure out a path where you can get the handles to swing
clearly and you're not colliding with other branches. And when you're cutting in a congested
tree like this one, then you've really got to think through which way you're going to approach the cut
so that you don't jam up against the tree and you can complete the cut cleanly. Now, as you get
longer into the pruning job and the job gets less congested, then that's not so much of an issue.
But initially, when you're working to do, let's say, rehabilitation on an overgrown tree or something
that's been neglected for some time, that is an issue you want to take into account. Now, there
are a couple of different kinds of pruners that are most commonly found in the market. What you're
looking at right here is called a bypass pruner. Why is that called a bypass? Well, it's very
scissors-like. Your cutting blade right here, which is very sharp, so I've got to be careful right
there, comes across a cutting surface, much like a scissor does, that is almost perpendicular. And
this creates a very sharp cutting plane right there. So it's very scissors-like. Again, called
bypass. The different type, called an anvil, is where the blade, let's call my hand the blade,
and this is the sharp edge, comes down on a flat plate that has a little groove in it, and that's
called an anvil cutter. So the cutter comes down, and in some cases it works really well, but it's
more prone to smashing the cut or leaving a ragged cut on the tree. What's the advantage? Well, they
don't tend to gum up as much with the material, and they clear themselves faster, but most people
use bypass types. Now, there's something else I want you to notice on this. The claim card said
titanium, and you can see right on this blade assembly here, it says titanium. That is a titanium
coating. This is not an entirely through and through titanium piece of metal. It is coated
with titanium for a couple of reasons. One, it makes the metal a little bit more slippery,
so as it cuts, it runs nicer for a longer period of time. It also does not gum up as readily. Things
don't stick to it as much, and it holds a nice edge when you sharpen on the back edge. And you
sharpen on the flat side, not on the beveled sides. Now, one of the things that we'll mention to you
is that since there is a gear system in this, that it's entirely appropriate to use some white
grease or something like that to just lubricate that from time to time. However, there's a trade
off with that as well. Grease tends to attract dust and dirt, and you can get a kind of a dirt ball
forming there. But from time to time, you can wipe that off, apply new grease, and that'll help this
lopping shear to run smoother and longer. This lopping shear cost us about $40 all set. One last
claim that is on the product card is it says that it cuts up to two inches in diameter. And as you
can see, the bottom hook right here, when this is fully extended, a two-inch branch indeed would fit
inside of that. The reason this is shaped this way is to grasp onto the branch so it doesn't
run away from you, so to speak, when you shut this in. It'll hold on to it and allow the blade to cut
through it. Will it cut up to two inches? Absolutely. And in this shot, you'll see an older fallen branch
that was quite dry being cut. And it also works really well for cutting branches that you've
already lopped off and they're on the ground and you're cutting them to smaller sections. You can
just step and repeat and cut along on the ground facing down this way and cutting as you go. So the
two-inch claim is a valid one, and you can really get some leverage by grasping on the handles,
moving them together, even if you just have only moderate strength. So for the price under $40,
will we buy it? Yeah, we did. We think it's a good value overall. If you have a favorite
lopping shear that you'd like to share with the rest of our viewer family, comment in the comments
below and let everybody else know about the great experience or product that you have found.
If you found this video to be helpful, won't you please like it? And better yet, subscribe to our
channel. That allows us to continue to put out great product reviews, videos about the garden,
the shop, and the kitchen. Hey, thanks for watching today. Until the next time,
this is Dirt Farmer Jay from DirtFarmerJay.com.